 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MVTX2804 Managed 8-Port 1000 Mbps Ethernet Switch Data Sheet Features * 8 Gigabit Ports with GMII and PCS interface * Gigabit Port can also support 100/10 Mbps MII interface * Provide Hot plug support for GMII/PCS module February 2003 Ordering Information MVTX2804AG 596 Pin HSBGA -40C to +85 oC * * * * High Performance Layer 2 Packet Forwarding (23.808M packets per second) and Filtering at Full-Wire Speed Maximum throughput is 8 Gbps non-blocking Centralized shared-memory architecture Consists of two Memory Domains at 133 MHz * Frame Buffer Domain: Two banks of ZBT-SRAM with 2M/4MB total * Switch Database Domain with 256K/512K SRAM Traffic Classification * * * Classify traffic into 8 transmission priorities per port Supports Delay Bounded, Strict Priority, and WFQ Provides 2 level dropping precedence with WRED mechanism * User controlled thresholds for WRED * * * Up to 64K MAC addresses to provide large node aggregation in wiring closet switches Provides Port based and ID Tagged VLAN (IEEE802.1Q) up to 4K VLAN Support IP Multicast with IGMP snooping up to 64K groups. * Classification based on layer 2, 3 markings * VLAN Priority field in VLAN tagged frame * DS/TOS field in IP packet * The precedence of above two classifications can be programmable Frame Data Buffer A ZBT-SRAM (1M/2MB) Frame Data Buffer B ZBT-SRAM (1M/2MB) SRAM 256/512K SW Database MAC Table 32bit SDB Interface LED MVTX2804 64bit FDB Interface 64bit Frame Engine Scheduler NM Database Search Engine Management Module GMII /PCS Port 0 GMII /PCS Port 1 GMII /PCS Port 2 GMII /PCS Port 3 GMII /PCS Port 4 GMII /PCS Port 5 GMII /PCS Port 6 GMII /PCS Port 7 16/8bitBus/ Serial CPU Figure 1 - MVTX2804 Functional Block Diagram 1 MVTX2804 QoS Support * * * * * * * * * * * Supports IEEE 802.1p/Q Quality of Service with 8 Priority Buffer Management: reserve buffers on per class and per port basis Port-based Priority: VLAN Priority with Tagged frame can be overwritten by the priority of PVID QoS features can be configured on a per port basis Packet Filtering and Port Security Static addressing filtering for source and/or destination MAC address Static learned MAC addresses will not be aged out Secure mode per port: Prevent learning for port in a secure mode Support per MAC per Port filtering Full Duplex Ethernet IEEE 802.3x Flow Control Provides Ethernet Multicast and Broadcast Control * Data Sheet * * * * * * * * * * 4 Port Trunking groups, 8 ports per group (Trunking can be based on source MAC and/or destination MAC and source port) LED signals provided by a serial or parallel interface CPU interface supports 16/8-bit CPU bus in managed mode and a synchronous Serial Interface and I2C interface in unmanaged mode SNMP/RMON support with CPU Built-in MIB counter Spanning tree with CPU Multiple Spanning trees (Per Spanning Tree Per VLAN) Hardware auto-negotiation through serial management interface (MDIO) for Gigabit Ethernet ports, supports 10/100/1000 Mbps BIST for internal and external SRAM-ZBT I2C EEPROM or synchronous serial port for configuration Packaged in 596-pin BGA Description The MVTX2800 family is a group of 1000 Mbps non-blocking Ethernet switch chips with on-chip address memory. A single chip provides a maximum of eight 1000 Mbps ports and a dedicated CPU interface with a 16/8-bit bus for managed and unmanaged switch applications. The MVTX2800 family consists of the following four products: * * * * MVTX2804 MVTX2803 MVTX2802 MVTX2801 8 8 4 4 Gigabit Gigabit Gigabit Gigabit ports ports ports ports Managed Unmanaged Managed Unmanaged The MVTX2804 supports up to 64K MAC addresses to aggregate traffic from multiple wiring closet stacks. The centralized shared-memory architecture allows a very high performance packet-forwarding rate of 11.904M packets per second at full wire speed. The chip is optimized to provide a low-cost, high performance workgroup, and wiring closet, layer 2 switching solution with 8 Gigabit Ethernet ports. Two Frame Buffer Memory domains utilize cost effective, high-performance ZBT-SRAM with aggregated bandwidth of 16Gbps to support full wire speed on all external ports simultaneously. With Strict priority, Delay Bounded, and WRR transmission scheduling, plus WRED memory congestion scheme, the chip provides powerful QoS functions for convergent network multimedia and mission-critical applications. The chip provides 8 transmission priorities and 2 level drop precedence. Traffic is assigned its transmission priority and dropping precedence based on the frame VLAN Tag priority or DS/TOS fields in IP packets. IP multicast snooping provides up to 64k simultaneous IP Multicast groups. With 4K IEEE 802.1Q VLANs, the MVTX2804 provides the ability to logically group users to control multicast traffic. 2 Zarlink Semiconductor Inc. Data Sheet MVTX2804 The MVTX2804 supports port trunking/load sharing on the 1000 Mbps ports with fail-over capability. The port trunking/load sharing can be used to group ports between interlinked switches to increase the effective network bandwidth. In full-duplex mode, IEEE 802.3x flow control is provided. The Physical Coding Sublayer (PCS) is integrated on-chip to provide a direct 10-bit GMII interface, or the PCS can be bypassed to provide an interface to existing fiber-based Gigabit Ethernet transceivers. Statistical information for Etherstat SNMP and Remote Monitoring Management Information Base (RMON MIB) are collected independently for each of the eight ports. Access to these statistical counter/registers is provided via the CPU interface. SNMP Management frames can be received and transmitted via the CPU interface, creating a complete network management solution. The MVTX2804 is fabricated using 0.25mm technology. Inputs, however, are 3.3V tolerant and the outputs are capable of directly interfacing to LVTTL levels. The MVTX2804 is packaged in a 596-pin Ball Grid Array package. Zarlink Semiconductor Inc. 3 MVTX2804 Data Sheet 4 Zarlink Semiconductor Inc. Data Sheet MVTX2804 Table of Contents 1.0 Block Functionality ..........................................................................................................13 1.1 Frame Data Buffer (FDB) Interfaces..........................................................................................................13 1.2 Switch Database (SDB) Interface..............................................................................................................13 1.3 GMII/PCS MAC Module (GMAC) ..............................................................................................................13 1.4 CPU Interface Module ...............................................................................................................................13 1.5 Management Module.................................................................................................................................13 1.6 Frame Engine ............................................................................................................................................13 1.7 Search Engine ...........................................................................................................................................13 1.8 LED Interface.............................................................................................................................................13 1.9 Internal Memory.........................................................................................................................................14 2.0 System Configuration ......................................................................................................14 2.1 Management and Configuration ................................................................................................................14 2.2 Managed Mode..........................................................................................................................................14 2.3 Register Configuration, Frame Transmission, and Frame Reception .......................................................16 2.3.1 Ethernet Frames ..............................................................................................................................16 2.3.2 Control Frames ................................................................................................................................16 2.4 Unmanaged Mode .....................................................................................................................................17 2.5 I2C Interface ..............................................................................................................................................17 2.5.1 Start Condition .................................................................................................................................17 2.5.2 Address ............................................................................................................................................17 2.5.3 Data Direction ..................................................................................................................................18 2.5.4 Acknowledgment..............................................................................................................................18 2.5.5 Data..................................................................................................................................................18 2.5.6 Stop Condition..................................................................................................................................18 2.6 Synchronous Serial Interface ....................................................................................................................18 2.6.1 Write Command ...............................................................................................................................19 2.6.2 Read Command ...............................................................................................................................19 3.0 Data Forwarding Protocol ...............................................................................................19 3.1 Unicast Data Frame Forwarding................................................................................................................19 3.2 Multicast Data Frame Forwarding .............................................................................................................20 3.3 Frame Forwarding To and From CPU .......................................................................................................20 4.0 Memory Interface..............................................................................................................21 4.1 Overview....................................................................................................................................................21 4.2 Detailed Memory Information ....................................................................................................................21 5.0 Search Engine ..................................................................................................................22 5.1 Search Engine Overview ...........................................................................................................................22 5.2 Basic Flow .................................................................................................................................................22 5.3 Search, Learning, and Aging .....................................................................................................................22 5.3.1 MAC Search.....................................................................................................................................22 5.3.2 Learning ...........................................................................................................................................23 5.3.3 Aging ................................................................................................................................................23 5.3.4 Data Structure ..................................................................................................................................23 5.3.5 VLAN Port Association Table...........................................................................................................23 6.0 Frame Engine....................................................................................................................24 6.1 Data Forwarding Summary........................................................................................................................24 6.2 Frame Engine Details ................................................................................................................................24 6.2.1 FCB Manager...................................................................................................................................24 6.2.2 Rx Interface......................................................................................................................................24 6.2.3 RxDMA.............................................................................................................................................24 6.2.4 TxQ Manager ...................................................................................................................................24 Zarlink Semiconductor Inc. v MVTX2804 Table of Contents Data Sheet 6.3 Port Control............................................................................................................................................... 25 6.4 TxDMA ...................................................................................................................................................... 25 7.0 Quality of Service and Flow Control .............................................................................. 25 7.1 Model ........................................................................................................................................................ 25 7.2 Four QoS Configurations .......................................................................................................................... 26 7.3 Delay Bound ............................................................................................................................................. 27 7.4 Strict Priority and Best Effort..................................................................................................................... 27 7.5 Weighted Fair Queuing ............................................................................................................................. 27 7.6 Shaper ...................................................................................................................................................... 28 7.7 WRED Drop Threshold Management Support.......................................................................................... 28 7.8 Buffer Management .................................................................................................................................. 29 7.8.1 Dropping When Buffers Are Scarce ................................................................................................ 30 7.9 Flow Control Basics .................................................................................................................................. 30 7.9.1 Unicast Flow Control ....................................................................................................................... 30 7.9.2 Multicast Flow Control ..................................................................................................................... 30 7.10 Mapping to IETF Diffserv Classes .......................................................................................................... 31 8.0 Port Trunking ................................................................................................................... 32 8.1 Features and Restrictions ......................................................................................................................... 32 8.2 Unicast Packet Forwarding ....................................................................................................................... 32 8.3 Multicast Packet Forwarding..................................................................................................................... 32 8.4 Preventing Multicast Packets from Looping Back to the Source Trunk .................................................... 32 9.0 LED Interface.................................................................................................................... 33 9.1 Introduction ............................................................................................................................................... 33 9.2 Serial Mode............................................................................................................................................... 33 9.3 Parallel Mode ............................................................................................................................................ 34 9.4 LED Control Registers .............................................................................................................................. 34 10.0 Hardware Statistics Counter......................................................................................... 35 10.1 Hardware Statistics Counters List........................................................................................................... 35 10.2 IEEE 802.3 HUB Management (RFC 1213) ........................................................................................... 36 10.2.1 Event Counters.............................................................................................................................. 36 10.3 IEEE - 802.1 Bridge Management (RFC 1286) ...................................................................................... 38 10.3.1 Event Counters.............................................................................................................................. 38 10.4 RMON - Ethernet Statistic Group (RFC 1757)........................................................................................ 39 10.4.1 Event Counters.............................................................................................................................. 39 11.0 Register Definition......................................................................................................... 41 11.1 Register Description................................................................................................................................ 41 11.2 Directly Accessed Registers ................................................................................................................... 47 11.2.1 INDEX_REG0................................................................................................................................ 47 11.2.2 INDEX_REG1 (only needed for CPU 8-bit bus mode) .................................................................. 47 11.2.3 DATA_FRAME_REG .................................................................................................................... 47 11.2.4 CONTROL_FRAME_REG ............................................................................................................ 47 11.2.5 COMMAND&STATUS................................................................................................................... 48 11.2.6 Interrupt Register........................................................................................................................... 48 11.2.7 Control Frame Buffer1 Access Register........................................................................................ 48 11.2.8 Control Frame Buffer2 Access Register........................................................................................ 49 11.3 Group 0 Address..................................................................................................................................... 49 11.3.1 MAC Ports Group .......................................................................................................................... 49 11.4 Group 1 Address..................................................................................................................................... 54 11.4.1 VLAN Group .................................................................................................................................. 54 11.5 Port VLAN Map ....................................................................................................................................... 57 vi Zarlink Semiconductor Inc. Data Sheet MVTX2804 Table of Contents 11.5.1 PVMODE........................................................................................................................................57 11.6 Group 2 Address .....................................................................................................................................58 11.6.1 Port Trunking Group.......................................................................................................................58 11.6.2 Multicast Hash Registers ...............................................................................................................68 11.7 Group 3 Address .....................................................................................................................................71 11.7.1 CPU Port Configuration Group.......................................................................................................71 11.7.2 RQS - Receive Queue Select ........................................................................................................74 11.7.3 RQSS - Receive Queue Status......................................................................................................75 11.7.4 TX_AGE - Tx Queue Aging timer...................................................................................................75 11.8 Group 4 Address .....................................................................................................................................75 11.8.1 Search Engine Group.....................................................................................................................75 11.9 Group 5 Address .....................................................................................................................................77 11.9.1 Buffer Control/QOS Group .............................................................................................................77 11.9.2 BMRC - Broadcast/Multicast Rate Control.....................................................................................81 11.9.3 UCC - Unicast Congestion Control ...............................................................................................81 11.9.4 MCC - Multicast Congestion Control..............................................................................................83 11.9.5 PRG - Port Reservation for Giga ports...........................................................................................83 11.9.6 FCB Reservation............................................................................................................................83 11.9.7 Classes Byte Gigabit Port 0 ...........................................................................................................86 11.9.8 Classes Byte Gigabit Port 1 ...........................................................................................................87 11.9.9 Classes Byte Gigabit Port 2 ...........................................................................................................88 11.9.10 Classes Byte Gigabit Port 3 .........................................................................................................89 11.9.11 Classes Byte Gigabit Port 4 .........................................................................................................90 11.9.12 Classes Byte Gigabit Port 5 .........................................................................................................91 11.9.13 Classes Byte Gigabit Port 6 .........................................................................................................92 11.9.14 Classes Byte Gigabit Port 7 .........................................................................................................93 11.9.15 Classes Byte Limit CPU ...............................................................................................................94 11.9.16 Classes WFQ Credit Set 0 ...........................................................................................................94 11.9.17 Classes WFQ Credit Port G1 .......................................................................................................96 11.9.18 Classes WFQ Credit Port G2 .......................................................................................................98 11.9.19 Classes WFQ Credit Port G3 .....................................................................................................100 11.9.20 Classes WFQ Credit Port G4 .....................................................................................................102 11.9.21 Classes WFQ Credit Port G5 .....................................................................................................104 11.9.22 Classes WFQ Credit Port G6 .....................................................................................................106 11.9.23 Classes WFQ Credit Port G7 .....................................................................................................108 11.9.24 Class 6 Shaper Control Port G0.................................................................................................110 11.9.25 Class 6 Shaper Control Port G1.................................................................................................111 11.9.26 Class 6 Shaper Control Port G2.................................................................................................111 11.9.27 Class 6 Shaper Control Port G3.................................................................................................111 11.9.28 Class 6 Shaper Control Port G4.................................................................................................112 11.9.29 Class 6 Shaper Control Port G5.................................................................................................112 11.9.30 Class 6 Shaper Control Port G6.................................................................................................113 11.9.31 Class 6 Shaper Control Port G7.................................................................................................113 11.9.32 RDRC0 - WRED Rate Control 0 ................................................................................................113 11.9.33 RDRC1 - WRED Rate Control 1 ................................................................................................115 11.10 Group 6 Address .................................................................................................................................115 11.10.1 MISC Group ...............................................................................................................................115 11.10.2 CHECKSUM - EEPROM Checksum..........................................................................................119 11.10.3 LED User....................................................................................................................................120 11.10.4 MIINP0 - MII Next Page Data Register 0 ...................................................................................124 11.10.5 MIINP1 - MII Next Page Data Register 1 ...................................................................................124 11.11 .............................................................................................................................................................124 Zarlink Semiconductor Inc. vii MVTX2804 Table of Contents Data Sheet 11.12 Group F Address ................................................................................................................................ 124 11.12.1 CPU Access Group ................................................................................................................... 124 11.12.2 DTST - Data Read Back Register ............................................................................................. 128 12.0 BGA and Ball Signal Description ............................................................................... 129 12.1 BGA Views (Top-View) ......................................................................................................................... 129 12.2 Power and Ground Distribution............................................................................................................. 130 12.3 Ball-Signal Descriptions ........................................................................................................................ 131 12.3.1 Ball Signal Description in Managed Mode................................................................................... 131 12.3.2 Ball - Signal Description in Unmanaged Mode........................................................................... 142 12.4 Ball Signal Name .................................................................................................................................. 154 12.5 AC/DC Timing ...................................................................................................................................... 160 12.5.1 Absolute Maximum Ratings......................................................................................................... 160 12.5.2 DC Electrical Characteristics....................................................................................................... 160 12.5.3 Recommended Operation Conditions ......................................................................................... 160 12.5.4 Typical CPU Timing Diagram for a CPU Write Cycle .................................................................. 161 12.5.5 Typical CPU Timing Diagram for a CPU Read Cycle.................................................................. 162 12.6 Local Frame Buffer ZBT SRAM Memory Interface ............................................................................... 163 12.6.1 Local ZBT SRAM Memory Interface A ........................................................................................ 163 12.6.2 Local ZBT SRAM Memory Interface B ........................................................................................ 164 12.7 Local Switch Database SBRAM Memory Interface............................................................................... 164 12.7.1 Local SBRAM Memory Interface ................................................................................................. 164 12.8 AC Characteristics ................................................................................................................................ 166 12.8.1 Media Independent Interface....................................................................................................... 166 12.8.2 Gigabit Media Independent Interface .......................................................................................... 167 12.8.3 PCS Interface .............................................................................................................................. 168 12.8.4 LED Interface .............................................................................................................................. 169 12.8.5 MDIO Input Setup and Hold Timing ............................................................................................ 169 12.8.6 I2C Input Setup Timing ................................................................................................................ 170 12.8.7 Serial Interface Setup Timing ...................................................................................................... 171 viii Zarlink Semiconductor Inc. Data Sheet MVTX2804 List of Figures Figure 1 - MVTX2804 Functional Block Diagram .................................................................................................... 1 Figure 2 - Overview of the MTVTX2804AG CPU Interface ................................................................................... 15 Figure 3 - Data Transfer Format for I2C Interface ................................................................................................. 17 Figure 4 - MVTX2804 SRAM Interface Block Diagram (DMAs for Gigaport Ports) .............................................. 21 Figure 5 - Buffer Partition Scheme Used in the MVTX2804 .................................................................................. 29 Figure 6 - Timing diagram for serial mode in LED interface. ................................................................................. 33 Figure 7 - Typical CPU Timing Diagram for a CPU Write Cycle ......................................................................... 161 Figure 8 - Typical CPU Timing Diagram for a CPU Read Cycle ......................................................................... 162 Figure 9 - Local Memory Interface - Output valid delay timing ............................................................................ 163 Figure 10 - Local Memory Interface - Input setup and hold timing ..................................................................... 164 Figure 11 - Local Memory Interface - Output valid delay timing .......................................................................... 164 Figure 12 - Local Memory Interface - Input setup and hold timing ..................................................................... 165 Figure 13 - Local Memory Interface - Output valid delay timing .......................................................................... 165 Figure 14 - AC Characteristics - Media Independent Interface .......................................................................... 166 Figure 15 - AC Characteristics - Media Independent Interface .......................................................................... 166 Figure 16 - AC Characteristics - GMII ................................................................................................................. 167 Figure 17 - AC Characteristics - Gigabit Media Independent Interface .............................................................. 167 Figure 18 - AC Characteristics - PCS Interface .................................................................................................. 168 Figure 19 - AC Characteristics - PCS Interface .................................................................................................. 168 Figure 20 - AC Characteristics - LED Interface .................................................................................................. 169 Figure 21 - MDIO Input Setup and Hold Timing .................................................................................................. 169 Figure 22 - MDIO Output Delay Timing .............................................................................................................. 170 Figure 23 - I2C Input Setup Timing ..................................................................................................................... 170 Figure 24 - I2C Output Delay Timing ................................................................................................................... 170 Figure 25 - Serial Interface Setup Timing ........................................................................................................... 171 Figure 26 - Serial Interface Output Delay Timing ................................................................................................ 171 Zarlink Semiconductor Inc. ix MVTX2804 Data Sheet x Zarlink Semiconductor Inc. Data Sheet MVTX2804 List of Tables Table 1 - Two-dimensional World Traffic ...............................................................................................................26 Table 2 - Four QoS configurations per port. ..........................................................................................................26 Table 3 - WRED Dropping Scheme. ......................................................................................................................28 Table 4 - Mapping between MVTX2804 and IETF Diffserv Classes for Gigabit Ports...........................................31 Table 5 - MVTX2804 Features Enabling IETF Diffserv Standards ........................................................................31 Table 6 - CPU Write Cycle...................................................................................................................................161 Table 7 - CPU Read Cycle...................................................................................................................................162 Table 8 - Local Memory Interface - Input setup and hold timing .........................................................................163 Table 9 - AC Characteristics - Local frame buffer ZBT-SRAM Memory Interface A ...........................................163 Table 10 - AC Characteristics - Local frame buffer ZBT-SRAM Memory Interface B .........................................164 Table 11 - AC Characteristics - Local Switch Database SBRAM Memory Interface...........................................165 Table 12 - AC Characteristics - Media Independent Interface ............................................................................166 Table 13 - AC Characteristics - Gigabit Media Independent Interface ................................................................168 Table 14 - AC Characteristics - PCS Interface....................................................................................................169 Table 15 - AC Characteristics - LED Interface ....................................................................................................169 Table 16 - MDIO Timing.......................................................................................................................................170 Table 17 - I2C Timing ..........................................................................................................................................171 Table 18 - Serial Interface Timing ........................................................................................................................171 Zarlink Semiconductor Inc. xi MVTX2804 Data Sheet xii Zarlink Semiconductor Inc. Data Sheet 1.0 1.1 MVTX2804 Block Functionality Frame Data Buffer (FDB) Interfaces The FDB interface supports pipelined ZBT-SRAM memory at 133 MHz. To ensure a non-blocking switch, two memory domains are required. Each domain has a 64-bit wide memory bus. At 133 MHz, the aggregate memory bandwidth is 17 Gbps, which is enough to support 8 Gigabit ports at full wire speed switching. A patent pending scheme is used to access the FDB memory. Each slot has one tick to read or write 8 bytes. 1.2 Switch Database (SDB) Interface A pipelined synchronous burst SRAM (SBRAM) memory is used to store the switch database information including MAC Table, VLAN Table and IP Multicast Table. Search Engine accesses the switch database via SDB interface. The SDB memory has 32-bit wide bus at 133MHz. 1.3 GMII/PCS MAC Module (GMAC) The GMII/PCS Media Access Control (MAC) module provides the necessary buffers and control interface between the Frame Engine (FE) and the external physical device (PHY). The MVTX2804 has two interfaces, GMII or PCS. The MAC of the MVTX2804 meets the IEEE 802.3z specification and supports the MII interface. It is able to operate in 10M/100M/1G in Full Duplex mode with a flow control mechanism. It has the options to insert Source Address/CRC/VLAN ID to each frame. The GMII/PCS Module also supports hot plug detection. 1.4 CPU Interface Module One extra port is dedicated to the CPU via the CPU interface module. The CPU interface utilizes a 16/8-bit bus in managed mode. It also supports a serial and an I2C interface, which provides an easy way to configure the system if unmanaged. 1.5 Management Module The CPU can send a control frame to access or configure the internal network management database. The Management Module decodes the control frame and executes the functions requested by the CPU. 1.6 Frame Engine The main function of the frame engine is to forward a frame to its proper destination port or ports. When a frame arrives, the frame engine parses the frame header (64 bytes) and formulates a switching request, which is sent to the search engine to resolve the destination port. The arriving frame is moved to the FDB. After receiving a switch response from the search engine, the frame engine performs transmission scheduling based on the frame's priority. The frame engine forwards the frame to the MAC module when the frame is ready to be sent. 1.7 Search Engine The Search Engine resolves the frame's destination port or ports according to the destination MAC address (L2) or IP multicast address (IP multicast packet) by searching the database. It also performs MAC learning, priority assignment, and trunking functions. 1.8 LED Interface The LED interface can be operated in a serial mode or a parallel mode. In the serial mode, the LED interface uses 3 pins for carrying 8 port status signals. In the parallel mode, the interface can drive LEDs by 8 status pins. The LED port is shared with bootstrap pins. In order to avoid mis-reading a buffer must be used to isolate the LED circuitry from the bootstrap pins during bootstrap cycle (the bootstraps are sampled at the rising edge of the #Reset). Zarlink Semiconductor Inc. 13 MVTX2804 1.9 Internal Memory Data Sheet Several internal tables are required and are described as follows: * * * * Frame Control Block (FCB) - Each FCB entry contains the control information of the associated frame stored in the FDB, e.g. frame size, read/write pointer, transmission priority, etc. Network Management (NM) Database - The NM database contains the information in the statistics counters and MIB. MCT Link Table - The MCT Link Table stores the linked list of MCT entries that have collisions in the external MAC Table. VLAN Port Aging Table - This table provides the aging status of VLAN Port association status. Search Engine maintains this table and informs the CPU when the entry is ready to age out. 2.0 2.1 System Configuration Management and Configuration Two modes are supported in the MVTX2804: managed and unmanaged. In managed mode, the MVTX2804 uses an 8- or 16-bit CPU interface very similar to the Industry Standard Architecture (ISA) specification. In unmanaged mode, the MVTX2804 has no CPU but can be configured by EEPROM using an I2C interface at bootup, or via a synchronous serial interface otherwise. 2.2 Managed Mode In managed mode, the MVTX2804 uses an 8- or 16-bit CPU interface very similar to the ISA bus. The MVTX2804 CPU interface provides for easy and effective management of the switching system. The figure below provides an overview of the CPU interface. 14 Zarlink Semiconductor Inc. Data Sheet CPU Interface 8/16-bit Data Bus 3-bit Addr I/O MUX MVTX2804 Index Reg 1 (Addr = 001) Index Reg 0 (Addr = 000) Config Data Reg (Addr = 010) 8-bit Data Bus CPU Frame Data Reg (Addr = 011) 8/16-bit Data Bus Command/ Status Reg (Addr = 100) Interrupt Reg (Addr = 101) Control Frame Data Reg (Addr = 110) Response Reg (RO) (Addr = 111) 16-bit Address 8/16-bit Data Bus Internal Registers Synchronous Serial Interface CPU Frame CPU Frame Receiver Transmit FIFO FIFO Frame Recent FIFO Frame Transmit FIFO1 Frame Transmit FIFO2 Interrupt Process MUX Search Engine Q0 Q1 RD_CYC, WR_CYC To Rate Control RAM Statistic Counter RAM FCB RAM MCT RAM External SRAM VLAN Index Figure 2 - Overview of the MTVTX2804AG CPU Interface Zarlink Semiconductor Inc. 15 MVTX2804 2.3 Register Configuration, Frame Transmission, and Frame Reception Data Sheet The MVTX2804 has many programmable parameters, covering such functions as QoS weights, VLAN control. In managed mode, the CPU interface provides an easy way of configuring these parameters. The parameters are contained in 8-bit configuration registers. The MVTX2804 allows indirect access to these registers, as follows: ! Two "index" registers (addresses 000 and 001) need to be written, to indicate the desired 16-bit register address. ! To indirectly configure the register addressed by the two index registers, a "configure data" register (address 010) must be written with the desired 8-bit data. ! Similarly, to read the value in the register addressed by the two index registers, the "configure data" register can now simply be read. In summary, access to the many internal registers is carried out simply by directly accessing only three registers - two registers to indicate the address of the desired parameter, and one register to read or write a value. Of course, because there is only one bus master, there can never be any conflict between reading and writing the configuration registers. 2.3.1 Ethernet Frames The CPU interface is also responsible for receiving and transmitting standard Ethernet frames to and from the CPU. To transmit a frame from the CPU ! The CPU writes a "data frame" register (address 011) with the data it wants to transmit. After writing all the data, it then writes the frame size, destination port number, and frame status. ! The MVTX2804 forwards the Ethernet frame to the desired destination port, no longer distinguishing the fact that the frame originated from the CPU. To receive a frame into the CPU ! ! The CPU receives an interrupt when an Ethernet frame is available to be received. Frame information arrives first in the data frame register. This includes source port number, frame size, and VLAN tag. ! The actual data follows the frame information. The CPU uses the frame size information to read the frame out. In summary, receiving and transmitting frames to and from the CPU is a simple process that uses one direct access register only. 2.3.2 Control Frames In addition to standard Ethernet frames described in the preceding section, the CPU is also called upon to handle special "Control frames," generated by the MVTX2804 and sent to the CPU. These proprietary frames are related to such tasks as statistics collection, MAC address learning, aging, etc. All Control frames are 64 bytes long. Transmitting and receiving these frames is similar to transmitting and receiving Ethernet frames, except that the register accessed is the "Control frame data" register (address 110). Specifically, there are eight types of control frames generated by the CPU and sent to the MVTX2804: * * * * * * * * Memory read request Memory write request Learn MAC address Delete MAC address Search MAC address Learn IP Multicast address Delete IP Multicast address Search IP Multicast address 16 Zarlink Semiconductor Inc. Data Sheet MVTX2804 Note: Memory read and write requests by the CPU may include VLAN table, spanning tree, statistic counters, and similar updates. In addition, there are nine types of Control Frames generated by the MVTX2804 and sent to the CPU: * * * * * * * * * Interrupt CPU when statistics counter rolls over Response to memory read request from CPU Learn MAC address Delete MAC address Delete IP Multicast address New VLAN port Age out VLAN port Response to search MAC address request from CPU Response to search IP Multicast address request from CPU Note: Deleting IP Multicast address requests by the MVTX2804 occur when the CPU issues a Learn IP Multicast address command but the search engine discovers no RAM space for storage. The format of the Control Frame is described in the processor interface application note. 2.4 Unmanaged Mode In unmanaged mode, the MVTX2804 can be configured by EEPROM (24C02 or compatible) via an I2C interface at boot time, or via a synchronous serial interface during operation. When the bootstrap Td[8] is set to `0' meaning EEPROM installed, the MVTX2804, acting as a master starts the data transfer from the memory to the switch. 2.5 I2C Interface The I2C interface uses two bus lines, a serial data line (SDA) and a serial clock line (SCL). The SCL line carries the control signals that facilitate the transfer of information from EEPROM to the switch. Data transfer is 8-bit serial and bi-directional, at 50 Kbps. Data transfer is performed between master and slave IC using a request / acknowledgment style of protocol. The master IC generates the timing signals and terminates data transfer. The figure below shows the data transfer format. START SLAVE ADDRESS R/W ACK DATA 1 (8 bits) ACK DATA 2 ACK DATA M ACK STOP Figure 3 - Data Transfer Format for I2C Interface 2.5.1 Start Condition Generated by the master, the MVTX2804. The bus is considered to be busy after the Start condition is generated. The Start condition occurs if while the SCL line is High, there is a High-to-Low transition of the SDA line. Other than in the Start condition (and Stop condition), the data on the SDA line must be stable during the High period of SCL. The High or Low state of SDA can only change when SCL is Low. In addition, when the I2C bus is free, both lines are High. 2.5.2 Address The first byte after the Start condition determines which slave the master will select. The slave in our case is the EEPROM. The first seven bits of the first data byte make up the slave address. Zarlink Semiconductor Inc. 17 MVTX2804 2.5.3 Data Direction Data Sheet The eighth bit in the first byte after the Start condition determines the direction (R/W) of the message. A master transmitter sets this bit to W; a master receiver sets this bit to R. 2.5.4 Acknowledgment Like all clock pulses, the master generates the acknowledgment-related clock pulse. However, the transmitter releases the SDA line (High) during the acknowledgment clock pulse. Furthermore, the receiver must pull down the SDA line during acknowledge pulse so that it remains stable Low during the High period of this clock pulse. An acknowledgment pulse follows every byte transfer. If a slave receiver does not acknowledge after any byte, then the master generates a Stop condition and aborts the transfer. If a master receiver does not acknowledge after any byte, then the slave transmitter must release the SDA line to let the master generate the Stop condition. 2.5.5 Data After the first byte containing the address, all bytes that follow are data bytes. Each byte must be followed by an acknowledge bit. Data is transferred MSB-first. 2.5.6 Stop Condition Generated by the master. The bus is considered to be free after the Stop condition is generated. The Stop condition occurs if while the SCL line is High, there is a Low-to-High transition of the SDA line. The I2C interface serves the function of configuring the MVTX2804 at boot time. The master is the MVTX2804, and the slave is the EEPROM memory. 2.6 Synchronous Serial Interface The synchronous serial interface serves the function of configuring the MVTX2804 not at boot time but via a PC. The PC serves as master and the MVTX2804 serves as slave. The protocol for the synchronous serial interface is nearly identical to the I2C protocol. The main difference is that there is no acknowledgment bit after each byte of data transferred. The unmanaged MVTX2804 uses a synchronous serial interface to program the internal registers. To reduce the number of signals required, the register address, command and data are shifted in serially through the PS_DO pin. PS_STROBE- pin is used as the shift clock. PS_DI- pin is used as data return path. Each command consists of four parts. * START pulse * Register Address * Read or Write command * Data to be written or read back Any command can be aborted in the middle by sending an ABORT pulse to the MVTX2804. A START command is detected when PS_DO is sampled high at PS_STROBE - leading edge, and PS_DO is sampled low when PS_STROBE- falls. An ABORT command is detected when PS_DO is sampled low at PS_STROBE - leading edge, and PS_DO is sampled high when PS_STROBE - falls. 18 Zarlink Semiconductor Inc. Data Sheet 2.6.1 Write Command MVTX2804 PS-STROBE2 Extra clocks after last 2 Extra clocks after last transfer transfer PS_DO A0 A1 A2 ... A9 A10 A11 A9 A10 A11 W D0 D1 D2 D3 D4 D5 D6 D7 DATA START ADDRESS COMMAND 2.6.2 Read Command PS_STROBE- PS_DO A0 A1 A2 ... A9 A10 A11 R A0 A1 A2 ... A9 A10 A11 R A1 A2 ... A9 A10 A11 START PS_DI ADDRESS COMMAND DATA D0 D1 D2 D3 D4 D5 D6 D0 D1 D2 D3 D4 D5 D6 D7 All registers in the MVTX2804 can be modified through this synchronous serial interface. 3.0 3.1 Data Forwarding Protocol Unicast Data Frame Forwarding When a frame arrives, it is assigned a handle in memory by the Frame Control Buffer Manager (FCB Manager). An FCB handle will always be available, because of advance buffer reservations. The memory (ZBT-SRAM) interface is two 64-bit buses, connected to two ZBT-SRAM domains, A and B. The Receive DMA (RxDMA) is responsible for multiplexing the data and the address. On a port's "turn," the RxDMA will move 8 bytes (or up to the end-of-frame) from the port's associated RxFIFO into memory (Frame Data Buffer, or FDB). Once an entire frame has been moved to the FDB, and a good end-of-frame (EOF) has been received, the Rx interface makes a switch request. The RxDMA arbitrates among multiple switch requests. The switch request consists of the first 64 bytes of a frame, containing among other things, the source and destination MAC addresses of the frame. The search engine places a switch response in the switch response queue of the frame engine when done. Among other information, the search engine will have resolved the destination port of the frame and will have determined that the frame is unicast. After processing the switch response, the Transmission Queue Manager (TxQ manager) of the frame engine is responsible for notifying the destination port that it has a frame to forward to it. But first, the TxQ manager has Zarlink Semiconductor Inc. 19 MVTX2804 Data Sheet to decide whether or not to drop the frame, based on global FDB reservations and usage, as well as TxQ occupancy at the destination. If the frame is not dropped, then the TxQ manager links the frame's FCB to the correct per-port-per-class TxQ. Unicast TxQ's are linked lists of transmission jobs, represented by their associated frames' FCBs. There is one linked list for each transmission class for each port. There are 8 classes for each of the 8 Gigabit ports - a total of 32 unicast queues. The TxQ manager is responsible for scheduling transmission among the queues representing different classes for a port. When the port control module determines that there is room in the MAC Transmission FIFO (TxFIFO) for another frame, it requests the handle of a new frame from the TxQ manager. The TxQ manager chooses among the head-of-line (HOL) frames from the per-class queues for that port, using a Zarlink Semiconductor scheduling algorithm. As at the transmit end, each of the 8 ports has time slots devoted solely to reading data from memory at the address calculated by port control. The Transmission DMA (TxDMA) is responsible for multiplexing the data and the address. On a port's turn, the TxDMA will move 8 bytes (or up to the EOF) from memory into the port's associated TxFIFO. After reading the EOF, the port control requests a FCB release for that frame. The TxDMA arbitrates among multiple buffer release requests. The frame is transmitted from the TxFIFO to the line. 3.2 Multicast Data Frame Forwarding After receiving the switch response, the TxQ manager has to make the dropping decision. A global decision to drop can be made, based on global FDB utilization and reservations. If so, then the FCB is released and the frame is dropped. In addition, a selective decision to drop can be made, based on the TxQ occupancy at some subset of the multicast packet's destinations. If so, then the frame is dropped at some destinations but not others, and the FCB is not released. If the frame is not dropped at a particular destination port, then the TxQ manager formats an entry in the multicast queue for that port and class. Multicast queues are physical queues (unlike the linked lists for unicast frames). There are 4 multicast queues for each of the 8 Gigabit ports. There is one multicast queue for every two unicast classes. During scheduling, the TxQ manager treats the unicast queue and the multicast queue of the same class as one logical queue. The port control requests a FCB release only after the EOF for the multicast frame has been read by all ports to which the frame is destined. 3.3 Frame Forwarding To and From CPU Frame forwarding from the CPU port to a regular transmission port is nearly the same as forwarding between transmission ports. The only difference is that the physical destination port must be indicated in addition to the destination MAC address. If an invalid port is indicated the frame is forwarded accordingly to the destination MAC address. Frame forwarding to the CPU port is nearly the same as forwarding to a regular transmission port. The only difference is in frame scheduling. Instead of using the patent-pending scheduling algorithms, scheduling for the CPU port is simply based on strict priority. That is, a frame in a high priority queue will always be transmitted before a frame in a lower priority queue. There are four output queues to the CPU and one receive queue. 20 Zarlink Semiconductor Inc. Data Sheet 4.0 4.1 MVTX2804 Memory Interface Overview The figure below illustrates the first part of the ZBT-SRAM interface for the MVTX2804. As shown, two ZBT-SRAM banks A and B are used, with a 64-bit bus connected to each. Each DMA can read and write from both bank A and bank B. During each tick, two memory operations will take place in parallel - one for bank A, and one for bank B. Because the clock frequency is 133 MHz, the total memory bandwidth is 128 bits 133 MHz = 17 Gbps, for frame data buffer (FDB) access. In addition, the figure shows that the 8 Gigabit ports are actually grouped into sets of 4. If TxDMA 0 is using bank B during a given memory slot, then TxDMA's 1-3 will never be using bank A during this same slot. As a result, TxDMA's 0-3 can share the same bank selector. Not shown in the figure are the CPU port RxDMA's and TxDMA's, each separately connected to its own bank selector. ZBT-SRAM Bank A ZBT-SRAM Bank B TxDMA 0-1 TxDMA 2-3 TxDMA 4-5 TxDMA 6-7 RxDMA 0-1 RxDMA 2-3 RxDMA 4-5 RxDMA 6-7 Figure 4 - MVTX2804 SRAM Interface Block Diagram (DMAs for Gigaport Ports) 4.2 Detailed Memory Information Because the bus for each bank is 64 bits wide, frames are broken into 8-byte granules, written to and read from memory. The first 8-byte granule gets written to Bank A, the second 8-byte granule gets written to Bank B, and so on in alternating fashion. When reading frames from memory, the same procedure is followed, first from A, then from B, and so on. The reading and writing from alternating memory banks can be performed with minimal waste of memory bandwidth. What's the worst case? For any speed port, in the worst case, a 1-byte-long EOF granule gets written to Bank A. This means that a 7-byte segment of Bank A bandwidth is idle, and furthermore, the next 8-byte segment of Bank B bandwidth is idle, because the first 8 bytes of the next frame will be written to Bank A, not B. This scenario results in a maximum 15 bytes of waste per frame, which is always acceptable because the interframe gap is 20 bytes. The CPU management port gets treated like any other port, reading and writing to alternating memory banks starting with Bank A. Search engine data is written to both banks in parallel. In this way, a search engine read operation could be performed by either bank at any time without a problem. Zarlink Semiconductor Inc. 21 MVTX2804 5.0 5.1 Data Sheet Search Engine Search Engine Overview The MVTX2804 search engine is optimized for high throughput searching, with enhanced features to support: * * * * * * * * * Up to 64K MAC addresses Up to 4K VLAN Up to 64K IP Multicast groups 4 groups of port trunking Traffic classification into 8 transmission priorities, and 2 drop precedence levels Packet filtering Security IP Multicast Per port, per VLAN Spanning Tree 5.2 Basic Flow Shortly after a frame enters the MVTX2804 and is written to the Frame Data Buffer (FDB), the frame engine generates a Switch Request, which is sent to the search engine. The switch request consists of the first 64 bytes of the frame, which contain all the necessary information for the search engine to perform its task. When the search engine is done, it writes to the Switch Response Queue, and the frame engine uses the information provided in that queue for scheduling and forwarding. In performing its task, the search engine extracts and compresses the useful information from the 64-byte switch request. Among the information extracted are the source and destination MAC addresses, the transmission and discard priorities, whether the frame is unicast or multicast, and VLAN ID. Requests are sent to the external SRAM Switch Database to locate the associated entries in the external MCT table. When all the information has been collected from external SRAM, the search engine has to compare the MAC address on the current entry with the MAC address for which it is searching. If it is not a match, the process is repeated on the internal MCT Table. All MCT entries other than the first of each linked list are maintained internal to the chip. If the desired MAC address is still not found, then the result is either learning (source MAC address unknown) or flooding (destination MAC address unknown). In addition, VLAN information is used to select the correct set of destination ports for the frame (for multicast), or to verify that the frame's destination port is associated with the VLAN (for unicast). If the destination MAC address belongs to a port trunk, then the trunk number is retrieved instead of the port number. But on which port of the trunk will the frame be transmitted? This is easily computed using a hash of the source and destination MAC addresses. When all the information is compiled, the switch response is generated, as stated earlier. The search engine also interacts with the CPU with regard to learning and aging. 5.3 5.3.1 Search, Learning, and Aging MAC Search The search block performs source MAC address and destination MAC address (or destination IP address for IP multicast) searching. As we indicated earlier, if a match is not found, then the next entry in the linked list must be examined, and so on until a match is found or the end of the list is reached. In tag based VLAN mode, if the frame is unicast, and the destination port is not a member of the correct VLAN, then the frame is dropped; otherwise, the frame is forwarded. If the frame is multicast, this same table is used to indicate all the ports to which the frame will be forwarded. Moreover, if port trunking is enabled, this block selects the destination port (among those in the trunk group). 22 Zarlink Semiconductor Inc. Data Sheet MVTX2804 In port based VLAN mode, a bitmap is used to determine whether the frame should be forwarded to the outgoing port. The main difference in this mode is that the bitmap is not dynamic. Ports cannot enter and exit groups because of real-time learning made by a CPU. The MAC search block is also responsible for updating the source MAC address timestamp and the VLAN port association timestamp, used for aging. 5.3.2 Learning The learning module learns new MAC addresses and performs port change operations on the MCT database. The goal of learning is to update this database as the networking environment changes over time. When CPU reporting is enabled, learning and port change will be performed when the CPU request queue has room, and a memory slot is available, and a "Learn MAC Address" message is sent to the CPU. When CPU reporting is disabled, learning and port change will be performed based on memory slot availability only. In tag based VLAN mode, if the source port is not a member of a classified VLAN, a "New VLAN Port" message is sent to the CPU. The CPU can decide whether or not the source port can be added to the VLAN. 5.3.3 Aging Aging time is controlled by register 400h and 401h. The aging module scans and ages MCT entries based on a programmable "age out" time interval. As we indicated earlier, the search module updates the source MAC address and VLAN port association timestamps for each frame it processes. When an entry is ready to be aged, the entry is removed from the table, and a "Delete MAC Address" message is sent to inform the CPU. Supported entry types are dynamic, static, source filter, destination filter, IP multicast, source and destination filter, and secure MAC address. Only dynamic entries can be aged; whether an entry is static or dynamic is maintained in the "status" field of the MCT data structure. 5.3.4 Data Structure The MCT data structure is used for searching for MAC addresses. The structure is maintained by hardware in the search engine. The CPU can make requests to add to, delete from, or search the MCT database. The database is essentially a hash table, with collisions resolved by chaining. The database is partially external, and partially internal, as described earlier: the first MCT entry of each linked list is always located in the external SRAM, and the subsequent MCTs are located internally. 5.3.5 31 Valid VLAN Port Association Table 30 Route 29 27 26 Port 8 to 0 is VLAN status Port 8 VLAN status Port 7 VLAN status Port 6 VLAN status Port 5 VLAN status Port 4 VLAN status Port 3 VLAN status Port 2 VLAN status Port 1 VLAN status Port 0 VLAN status 0 Reserved VLAN STATUS [2:0] * * * * * * 000:Not a valid entry 001:Blocking status, no RX and TX 010:Not a VLAN member, spanning tree learn status 011:VLAN member, spanning tree learn status 100:Not a VLAN member, spanning tree forward status 101:VLAN member and is subject to aging, spanning tree forward status (Don't use) Zarlink Semiconductor Inc. 23 MVTX2804 * 110:VLAN member and is subject to aging, spanning tree forward status * 111:VLAN member and is not subject to aging, spanning tree forward status CPU can create static VLAN port by writing the static status to the VLAN- PORT status entry. Data Sheet Dynamic VLAN and Port association can be created by writing "110" to the VLAN STATUS. Hardware will age and refresh the entry based on the VLAN - PORT activity. When the VLAN - PORT is ready to be aged out, a message is sent to CPU and CPU can remove the VLAN - PORT association by writing "000" to the VLAN STATUS. As a result, the VLAN and PORT are no long associated and the VLAN domain is shrunk. 6.0 6.1 * * * * Frame Engine Data Forwarding Summary * * Enters the device at the RxMAC, the RxDMA will move the data from the MAC RxFIFO to the FDB. Data is moved in 8-byte granules in conjunction with the scheme for the SRAM interface. A switch request is sent to the Search Engine. The Search Engine processes the switch request. A switch response is sent back to the Frame Engine and indicates whether the frame is unicast or multicast, and its destination port or ports. A VLAN table lookup is performed as well. A Transmission Scheduling Request is sent in the form of a signal notifying the TxQ manager. Upon receiving a Transmission Scheduling Request, the device will format an entry in the appropriate Transmission Scheduling Queue (TxSch Q) or Queues. There is 8 transmission queues per Gigabit port, one for each priority. Creation of a queue entry either involves linking a new job to the appropriate linked list if unicast, or adding an entry to a physical queue if multicast. When the port is ready to accept the next frame, the TxQ manager will get the head-of-line (HOL) entry of one of the TxSch Qs, according to the transmission scheduling algorithm (so as to ensure per-class quality of service). The unicast linked list and the multicast queue for the same port-class pair are treated as one logical queue. The TxDMA will pull frame data from the memory and forward it granule-by-granule to the MAC TxFIFO of the destination port. 6.2 Frame Engine Details This section briefly describes the functions of each of the modules of the MVTX2804 frame engine. 6.2.1 FCB Manager The FCB manager allocates FCB handles to incoming frames, and releases FCB handles upon frame departure. The FCB manager is also responsible for enforcing buffer reservations and limits. The default values can be determined by referring to Chapter 8. In addition, the FCB manager is responsible for buffer aging, and for linking unicast forwarding jobs to their correct TxSch Q. The buffer aging can be enabled or disabled by the bootstrap pin and the aging time is defined in register FCBAT. 6.2.2 Rx Interface The Rx interface is mainly responsible for communicating with the RxMAC. It keeps track of the start and end of frame and frame status (good or bad). Upon receiving an end of frame that is good, the Rx interface makes a switch request. 6.2.3 RxDMA The RxDMA arbitrates among switch requests from each Rx interface. It also buffers the first 64 bytes of each frame for use by the search engine when the switch request has been made. 6.2.4 TxQ Manager First, the TxQ manager checks the per-class queue status and global Reserved resource situation, and using this information, makes the frame dropping decision after receiving a switch response. If the decision is not to drop, the TxQ manager requests that the FCB manager link the unicast frame's FCB to the correct per-port-per-class TxQ. If multicast, the TxQ manager writes to the multicast queue for that port and class. The 24 Zarlink Semiconductor Inc. Data Sheet MVTX2804 TxQ manager can also trigger source port flow control for the incoming frame's source if that port is flow control enabled. Second, the TxQ manager handles transmission scheduling; it schedules transmission among the queues representing different classes for a port. Once a frame has been scheduled, the TxQ manager reads the FCB information and writes to the correct port control module. 6.3 Port Control The port control module calculates the SRAM read address for the frame currently being transmitted. It also writes start of frame information and an end of frame flag to the MAC TxFIFO. When transmission is done, the port control module requests that the buffer be released. 6.4 TxDMA The TxDMA multiplexes data and address from port control, and arbitrates among buffer release requests from the port control modules. 7.0 7.1 Quality of Service and Flow Control Model Quality of service (QoS) is an all-encompassing term for which different people have different interpretations. In this chapter, by quality of service assurances, we mean the allocation of chip resources so as to meet the latency and bandwidth requirements associated with each traffic class. We do not presuppose anything about the offered traffic pattern. If the traffic load is light, then ensuring quality of service is straightforward. But if the traffic load is heavy, the MVTX2804 must intelligently allocate resources so as to assure quality of service for high priority data. We assume that the network manager knows his applications, such as voice, file transfer, or web browsing, and their relative importance. The manager can then subdivide the applications into classes and set up a service contract with each. The contract may consist of bandwidth or latency assurances per class. Sometimes it may even reflect an estimate of the traffic mix offered to the switch, though this is not required. The table below shows examples of QoS applications with eight transmission priorities, including best effort traffic for which we provide no bandwidth or latency assurances. Low Drop Subclass (If class is oversubscribed, these packets are the last to be dropped.) Sample application: control information Sample applications: phone calls; circuit emulation Sample application: interactive activities Sample application: web business Sample application: file backups Sample application: training video; other multimedia Sample application: non-critical interactive activities Sample application: non-critical interactive activities Class Example Assured Bandwidth (user defined) High Drop Subclass (If class is oversubscribed, these packets are the first to be dropped.) Highest transmission priorities, P7 Latency < 200 s Highest transmission priorities, P6 Latency < 200 s Middle transmission priorities, P5 Latency < 400 s Middle transmission priorities, P4 Latency < 800 s Low transmission priorities, P3 Latency < 1600 s 300 Mbps 200 Mbps 125 Mbps 250 Mbps 80 Mbps Zarlink Semiconductor Inc. 25 MVTX2804 Example Assured Bandwidth (user defined) Low Drop Subclass (If class is oversubscribed, these packets are the last to be dropped.) Sample application: email Data Sheet Class High Drop Subclass (If class is oversubscribed, these packets are the first to be dropped.) Sample application: web research Low transmission priorities, P2 Latency < 3200 s Best effort, P1-P0 TOTAL 45 Mbps - Sample application: casual web browsing 1 Gbps Table 1 - Two-dimensional World Traffic In our model, it is possible that a class of traffic may attempt to monopolize system resources by sending data at a rate in excess of the contractually assured bandwidth for that class. A well-behaved class offers traffic at a rate no greater than the agreed-upon rate. By contrast, a misbehaving class offers traffic that exceeds the agreed-upon rate. A misbehaving class is formed from an aggregation of misbehaving microflows. To achieve high link utilization, a misbehaving class is allowed to use any idle bandwidth. However, the quality of service (QoS) received by well-behaved classes must never suffer. As Table 1 illustrates, each traffic class may have its own distinct properties and applications. As shown, classes may receive bandwidth assurances or latency bounds. In the example, P7, the highest transmission class, requires that all frames be transmitted within 0.2 ms, and receives 30% of the 1 Gbps of bandwidth at that port. Best-effort (P1-P0) traffic forms a lower tier of service that only receives bandwidth when none of the other classes have any traffic to offer. In addition, each transmission class has two subclasses, high-drop and low-drop. Well-behaved users should not lose packets. But poorly behaved users - users who send data at too high a rate - will encounter frame loss, and the first to be discarded will be high-drop. Of course, if this is insufficient to resolve the congestion, eventually some low-drop frames are dropped as well. Table 1 shows that different types of applications may be placed in different boxes in the traffic table. For example, web search may fit into the category of high-loss, high-latency-tolerant traffic, whereas VoIP fits into the category of low-loss, low-latency traffic. 7.2 Four QoS Configurations There are four basic pieces to QoS scheduling in the MVTX2804: strict priority (SP), delay bound, weighted fair queuing (WFQ), and best effort (BE). Using these four pieces, there are four different modes of operation, as shown in Table 2. P7 Op1 (default) Op2 Op3 Op4 Delay Bound SP SP WFQ Table 2 - Four QoS configurations per port. The default configuration is six delay-bounded queues and two best-effort queues. The delay bounds per class are 0.16 ms for P7 and P6, 0.32 ms for P5, 0.64 ms for P4, 1.28 ms for P3, and 2.56 ms for P2. Best effort traffic is only served when there is no delay-bounded traffic to be served. P1 has strict priority over P0. Delay Bound WFQ P6 P5 P4 P3 P2 BE BE P1 P0 26 Zarlink Semiconductor Inc. Data Sheet MVTX2804 We have a second configuration in which there are two strict priority queues, four delay bounded queues, and two best effort queues. The delay bounds per class are 0.32 ms for P5, 0.64 ms for P4, 1.28 ms for P3, and 2.56 ms for P2. If the user is to choose this configuration, it is important that P7-P6 (SP) traffic be either policed or implicitly bounded (e.g. if the incoming SP traffic is very light and predictably patterned). Strict priority traffic, if not admission-controlled at a prior stage to the MVTX2804, can have an adverse effect on all other classes' performance. P7 and P6 are both SP classes, and P7 has strict priority over P6. The third configuration contains two strict priority queues and six queues receiving a bandwidth partition via WFQ. As in the second configuration, strict priority traffic needs to be carefully controlled. In the fourth configuration, all queues are served using a WFQ service discipline. 7.3 Delay Bound In the absence of a sophisticated QoS server and signalling protocol, the MVTX2804 may not be assured of the mix of incoming traffic ahead of time. To cope with this uncertainty, our delay assurance algorithm dynamically adjusts its scheduling and dropping criteria, guided by the queue occupancies and the due dates of their head-of-line (HOL) frames. As a result, we assure latency bounds for all admitted frames with high confidence, even in the presence of system-wide congestion. Our algorithm identifies misbehaving classes and intelligently discards frames at no detriment to well-behaved classes. Our algorithm also differentiates between high-drop and low-drop traffic with a weighted random early drop (WRED) approach. Random early dropping prevents congestion by randomly dropping a percentage of high-drop frames even before the chip's buffers are completely full, while still largely sparing low-drop frames. This allows high-drop frames to be discarded early, as a sacrifice for future low-drop frames. Finally, the delay bound algorithm also achieves bandwidth partitioning among classes. 7.4 Strict Priority and Best Effort When strict priority is part of the scheduling algorithm, if a queue has even one frame to transmit, it goes first. Two of our four QoS configurations include strict priority queues. The goal is for strict priority classes to be used for IETF expedited forwarding (EF), where performance guarantees are required. As we have indicated, it is important that strict priority traffic be either policed or implicitly bounded, so as to keep from harming other traffic classes. When best effort is part of the scheduling algorithm, a queue only receives bandwidth when none of the other classes have any traffic to offer. Two of our four QoS configurations include best effort queues. The goal is for best effort classes to be used for non-essential traffic, because we provide no assurances about best effort performance. However, in a typical network setting, much best effort traffic will indeed be transmitted, and with an adequate degree of expediency. Because we do not provide any delay assurances for best effort traffic, we do not enforce latency by dropping best effort traffic. Furthermore, because we assume that strict priority traffic is carefully controlled before entering the MVTX2804, we do not enforce a fair bandwidth partition by dropping strict priority traffic. To summarize, dropping to enforce quality of service (i.e. bandwidth or delay) does not apply to strict priority or best effort queues. We only drop frames from best effort and strict priority queues when global buffer resources become scarce. 7.5 Weighted Fair Queuing In some environments - for example, in an environment in which delay assurances are not required, but precise bandwidth partitioning on small time scales is essential - WFQ may be preferable to a delay-bounded scheduling discipline. The MVTX2804 provides the user with a WFQ option with the understanding that delay assurances cannot be provided if the incoming traffic pattern is uncontrolled. The user sets eight WFQ "weights" such that all weights are whole numbers and sum to 64. This provides per-class bandwidth partitioning with error within 2%. In WFQ mode, though we do not assure frame latency, the MVTX2804 still retains a set of dropping rules that helps to prevent congestion and trigger higher level protocol end-to-end flow control. Zarlink Semiconductor Inc. 27 MVTX2804 Data Sheet As before, when strict priority is combined with WFQ, we do not have special dropping rules for the strict priority queues, because the input traffic pattern is assumed to be carefully controlled at a prior stage. However, we do indeed drop frames from SP queues for global buffer management purposes. In addition, queues P1 and P0 are treated as best effort from a dropping perspective, though they still are assured a percentage of bandwidth from a WFQ scheduling perspective. What this means is that these particular queues are only affected by dropping when the global buffer count becomes low. 7.6 Shaper Although traffic shaping is not a primary function of the MVTX2804, the chip does implement a shaper for expedited forwarding (EF). Our goal in shaping is to control the peak and average rate of traffic exiting the MVTX2804. Shaping is limited to class P6 (the second highest priority). This means that class P6 will be the class used for EF traffic. (By contrast, we assume class P7 will be used for control packets only.) If shaping is enabled for P6, then P6 traffic must be scheduled using strict priority. With reference to Table 2, only the middle two QoS configurations may be used. Peak rate is set using a programmable whole number, no greater than 64 (register QOS-CREDIT_C6_Gn). For example, if the setting is 32, then the peak rate for shaped traffic is 32/64 1000 Mbps = 500 Mbps. Average rate is also a programmable whole number, no greater than 64, and no greater than the peak rate. For example, if the setting is 16, then the average rate for shaped traffic is 16/64 1000 Mbps = 250 Mbps. As a consequence of the above settings in our example, shaped traffic will exit the MVTX2804 at a rate always less than 500 Mbps, and averaging no greater than 250 Mbps. Also, when shaping is enabled, it is possible for a P6 queue to explode in length if fed by a greedy source. The reason is that a shaper is by definition not work-conserving; that is, it may hold back from sending a packet even if the line is idle. Though we do have global resource management, we do nothing to prevent this situation locally. We assume SP traffic is policed at a prior stage to the MVTX2804. 7.7 WRED Drop Threshold Management Support To avoid congestion, the Weighted Random Early Detection (WRED) logic drops packets according to specified parameters. The following table summarizes the behaviour of the WRED logic. P7 Level 1 N 240 Level 2 N 280 Level 3 N 320 Table 3 - WRED Dropping Scheme. P6 P5 P4 P3 P2 High Drop X% P7 A KB P6 B KB P5 C KB P4 D KB P3 E KB P2 F KB Y% 100% Low Drop 0% Z% 100% In the table, |Px| is the byte count in queue Px. The WRED logic has three drop levels, depending on the value of N, which is based on the number of bytes in the priority queues. If delay bound scheduling is used, N equals 16|P7| + 16|P6| + 8|P5| + 4|P4| + 2|P3| + |P2|. If WFQ scheduling is used, N equals |P7| + |P6| + |P5| + |P4| + |P3| + |P2|. Each drop level has defined high-drop and low-drop percentages, which indicate the percentage of high-drop and low-drop packets that will be dropped at that level. The X, Y, and Z percent parameters can be programmed using the registers RDRC0 and RDRC1. Parameters A-F are the byte count thresholds for each priority queue, and are also programmable. When using delay bound scheduling, the values selected for A-F also control the approximate bandwidth partition among the traffic classes; see application note. 28 Zarlink Semiconductor Inc. Data Sheet 7.8 Buffer Management MVTX2804 Because the number of frame data buffer (FDB) slots is a scarce resource, and because we want to ensure that one misbehaving source port or class cannot harm the performance of a well-behaved source port or class, we introduce the concept of buffer management into the MVTX2804. Our buffer management scheme is designed to divide the total buffer space into numerous reserved regions and one shared pool, (see Figure 4). As shown in the figure, the FDB pool is divided into several parts. A reserved region for temporary frames stores frames prior to receiving a switch response. Such a temporary region is necessary, because when the frame first enters the MVTX2804, its destination port and class are as yet unknown, and so the decision to drop or not needs to be temporarily postponed. This ensures that every frame can be received first before subjecting it to the frame drop discipline after classifying. Six reserved sections, one for each of the highest six priority classes, ensure a programmable number of FDB slots per class. The lowest two classes do not receive any buffer reservation. Another segment of the FDB reserves space for each of the 8 Gigabit ports and CPU port. These source port buffer reservations are programmable. These 9 reserved regions make sure that no well-behaved source port can be blocked by another misbehaving source port. In addition, there is a shared pool, which can store any type of frame. The registers related to the Buffer Management logic are * * * * * * * * PRG- Port Reservation for Gigabit Ports and CPU port SFCB- Share FCB Size C2RS- Class 2 Reserved Size C3RS- Class 3 Reserved Size C4RS- Class 4 Reserved Size C5RS- Class 5 Reserved Size C6RS- Class 6 Reserved Size C7RS- Class 7 Reserved Size Temporary Reservation RTMP Per-Class Reservations RP7, RP6,...RP2 Shared Pool S Per-Source Reservations 8-R1G Figure 5 - Buffer Partition Scheme Used in the MVTX2804 Zarlink Semiconductor Inc. 29 MVTX2804 7.8.1 Dropping When Buffers Are Scarce Data Sheet The following is a summary of the two examples of local dropping discussed earlier in this chapter: If a queue is a delay-bounded queue, we have a multi-level WRED drop scheme, designed to control delay and partition bandwidth in case of congestion. * If a queue is a WFQ-scheduled queue, we have a multi-level WRED drop scheme, designed to prevent congestion. In addition to these reasons for dropping, the MVTX2804 also drops frames when global buffer space becomes scarce. The function of buffer management is to ensure that such droppings cause as little blocking as possible. * 7.9 Flow Control Basics Because frame loss is unacceptable for some applications, the MVTX2804 provides a flow control option. When flow control is enabled, scarcity of buffer space in the switch may trigger a flow control signal; this signal tells a source port, sending a packet to this switch, to temporarily hold off. While flow control offers the clear benefit of no packet loss, it also introduces a problem for quality of service. When a source port receives an Ethernet flow control signal, all microflows originating at that port, well-behaved or not, are halted. A single packet destined for a congested output can block other packets destined for uncongested outputs. The resulting head-of-line blocking phenomenon means that quality of service cannot be assured with high confidence when flow control is enabled. In the MVTX2804, each source port can independently have flow control enabled or disabled. For flow control enabled ports, by default all frames are treated as lowest priority during transmission scheduling. This is done so that those frames are not exposed to the WRED Dropping scheme. Frames from flow control enabled ports feed to only one queue at the destination, the queue of lowest priority. What this means is that if flow control is enabled for a given source port, then we can guarantee that no packets originating from that port will be lost, but at the possible expense of minimum bandwidth or maximum delay assurances. In addition, these "downgraded" frames may only use the shared pool or the per-source reserved pool in the FDB; frames from flow control enabled sources may not use reserved FDB slots for the highest six classes (P2-P7). The MVTX2804 does provide a system-wide option of permitting normal QoS scheduling (and buffer use) for frames originating from flow control enabled ports. When this programmable option is active, it is possible that some packets may be dropped, even though flow control is on. The reason is that intelligent packet dropping is a major component of the MVTX2804's approach to ensuring bounded delay and minimum bandwidth for high priority flows. 7.9.1 Unicast Flow Control For unicast frames, flow control is triggered by source port resource availability. Recall that the MVTX2804's buffer management scheme allocates a reserved number of FDB slots for each source port. If a programmed number of a source port's reserved FDB slots have been used, then flow control Xoff is triggered. Xon is triggered when a port is currently being flow controlled, and all of that port's reserved FDB slots have been released. Note that the MVTX2804's per-source-port FDB reservations assure that a source port that sends a single frame to a congested destination will not be flow controlled. 7.9.2 Multicast Flow Control In unmanaged mode, a global buffer counter triggers flow control for multicast frames. When the system exceeds a programmable threshold of multicast packets, Xoff is triggered. Xon is triggered when the system returns below this threshold. MCC register programs the threshold. In managed mode, per-VLAN flow control is used for multicast frames. In this case, flow control is triggered by congestion at the destination. The MVTX2804 checks each destination to which a multicast packet is headed. For each destination port, the occupancy of the lowest-priority transmission queue (measured in number of 30 Zarlink Semiconductor Inc. Data Sheet MVTX2804 frames) is compared against a programmable congestion threshold. If congestion is detected at even one of the packet's destinations, then Xoff is triggered. In addition, each source port has an 8-bit port map recording which port or ports of the multicast frame's fanout were congested at the time Xoff was triggered. All ports are continuously monitored for congestion, and a port is identified as uncongested when its queue occupancy falls below a fixed threshold. When all those ports that were originally marked as congested in the port map have become uncongested, then Xon is triggered, and the 8-bit vector is reset to zero. The MVTX2804 also provides the option of disabling multicast flow control. Note: If port flow control is on, QoS performance will be affected. 7.10 Mapping to IETF Diffserv Classes The mapping between priority classes discussed in this chapter and elsewhere is shown below. MVTX2804 IETF P7 NM P6 EF P5 AF0 P4 AF1 P3 AF2 P2 AF3 P1 BE0 P0 BE1 Table 4 - Mapping between MVTX2804 and IETF Diffserv Classes for Gigabit Ports As the table illustrates, P7 is used solely for network management (NM) frames. P6 is used for expedited forwarding service (EF). Classes P2 through P5 correspond to an assured forwarding (AF) group of size 4. Finally, P0 and P1 are two best effort (BE) classes. Features of the MVTX2804 that correspond to the requirements of their associated IETF classes are summarized in the table below. Network management (NM) and Expedited forwarding (EF) * * * * * * * * * Best effort (BE) * * * * Global buffer reservation for NM and EF Shaper for EF traffic Option of strict priority scheduling No dropping if admission controlled Four AF classes Programmable bandwidth partition, with option of WFQ service Option of delay-bounded service keeps delay under fixed levels even if not admission-controlled Random early discard, with programmable levels Global buffer reservation for each AF class Two BE classes Service only when other queues are idle means that QoS not adversely affected Random early discard, with programmable levels Traffic from flow control enabled ports automatically classified as BE Assured forwarding (AF) Table 5 - MVTX2804 Features Enabling IETF Diffserv Standards Zarlink Semiconductor Inc. 31 MVTX2804 8.0 8.1 Data Sheet Port Trunking Features and Restrictions A port group (i.e. trunk) can include up to 8 physical ports, but all of the ports in a group must be in the same MVTX2804. In managed mode, there are four trunk groups total. In unmanaged mode, the MVTX2804 provides several pre-assigned trunk group options, containing as many as 4 ports per group, or alternatively, as many as 4 total groups. Load distribution among the ports in a trunk for unicast is performed using hashing based on source MAC address and destination MAC address. The other options include source MAC address only, destination MAC address only. Load distribution for multicast is performed similarly. If a VLAN includes any of the ports in a trunk group, all the ports in that trunk group should be in the same VLAN member map. The MVTX2804 also provides a safe fail-over mode for port trunking automatically. If one of the ports in the trunking group goes down, the MVTX2804 will automatically redistribute the traffic over to the remaining ports in the trunk in unmanaged mode. In managed mode, the software can perform similar tasks. 8.2 Unicast Packet Forwarding The search engine finds the destination MCT entry, and if the status field says that the destination address found belongs to a trunk, then the group number is retrieved instead of the port number. In addition, if the source address belongs to a trunk, then the source port's trunk membership register is checked to determine if the address has moved. A hash key is used to determine the appropriate forwarding port, based on some combination of the source and destination MAC addresses for the current packet. The search engine retrieves the VLAN member ports from the VLAN index table, which consists of 4K entries. The search engine retrieves the VLAN member ports from the ingress port's VLAN map. Based on the destination MAC address, the search engine determines the egress port from the MCT database. If the egress port is a member of a trunk group, the packet can be distributed to the other members of that trunk group. The VLAN map is used to check whether the egress port is a member of the VLAN, based on the ingress port. If it is a member, the packet is forwarded otherwise it is discarded. 8.3 Multicast Packet Forwarding For multicast packet forwarding, the device must determine the proper set of ports from which to transmit the packet based on the VLAN index and hash key. Two functions are required in order to distribute multicast packets to the appropriate destination ports in a port trunking environment. * * Determining one forwarding port per group. For multicast packets, all but one port per group, the forwarding port, must be excluded. 8.4 Preventing Multicast Packets from Looping Back to the Source Trunk The search engine needs to prevent a multicast packet from sending to a port that is in the same trunk group with the source port. This is because, when we select the primary forwarding port for each group, we do not take the source port into account. To prevent this, we simply apply one additional filter, so as to block that forwarding port for this multicast packet. 32 Zarlink Semiconductor Inc. Data Sheet 9.0 9.1 MVTX2804 LED Interface Introduction The MVTX2804 LED block provides two interfaces: a serial output channel, and a parallel time-division interface. The serial output channel provides port status information from the MVTX2804 chip in a continuous serial stream. This means that a low cost external device must be used to decode the serial data and to drive an LED array for display. By contrast, the parallel time-division interface supports a glueless LED module. Indeed, the parallel interface can directly drive low-current LEDs without any extra logic. The pin LED_PM is used to select serial or parallel mode. For some LED signals, the interface also provides a blinking option. Blinking may be enabled for LED signals TxD, RxD, COL, and FC (to be described later). The pin LED_BLINK is used to enable blinking, and the blinking frequency is around 160 ms. 9.2 Serial Mode In serial mode, the following pins are utilized: * * * LED_SYNCO - a sync pulse that defines the boundary between status frames LED_CLKO - the clock signal LED_DO - a continuous serial stream of data for all status LEDs that repeats once every frame time In each cycle (one frame of status information, or one sync pulse), 16x8 bits of data are transmitted on the LED_DO signal. The sequence of transmission of data bits is as shown in the figure below: LE_SYNCO LE_DO P0 info P1 info P2 info P3 info P4 info P5 info P6 info P7 info U0 U1 U2 U3 U4 U5 U6 U7 LE_CLKO 0 FC 1 TxD 2 RxD 3 LNK 4 SP0 5 SP1 6 FDX 7 COL Figure 6 - Timing diagram for serial mode in LED interface. The status bits shown in here are flow control (FC), transmitting data (TxD), receiving data (RxD), link up (LNK), speed (SP0 and SP1), full duplex (FDX), and collision (COL). Note that SP[1:0] is defined as 10 for 1 Gbps, 01 for 100 Mbps, and 00 for 10 Mbps. Also note that U0-U7 represent user-defined sub-frames in which additional status information may be embedded. We will see later that the MVTX2804 provides registers that can be written by the CPU to indicate this additional status information as it becomes available. Zarlink Semiconductor Inc. 33 MVTX2804 9.3 Parallel Mode Data Sheet In parallel mode, the following pins are utilized: * LED_PORT_SEL[9:0] - indicates which of the 8 Gigabit port status bytes or 2 user-defined status bytes is being read out * LED_BYTEOUT_[7:0] - provides 8 bits for 8 different port status indicators. Note that these bits are active low. By default, the system is in parallel mode. In parallel mode, the 10 status bytes are scanned in a continuous loop, with one byte read out per clock cycle, and the appropriate port select bit asserted. 9.4 LED Control Registers An LED Control Register can be used for programming the LED clock rate, sample hold time, and pattern in parallel mode. In addition, the MVTX2804 provides 8 registers called LEDUSER[7:0] for user-defined status bytes. During operation, the CPU can write values to these registers, which will be read out to the LED interface output (serial or parallel). Only LEDUSER[1:0] are used in parallel mode. The content of the LEDUSER registers will be sent out by the LED serial shift logic, or in parallel mode, a byte at a time. Because in parallel mode there are only two user-defined registers, LEDUSER[7:2] is shared with LEDSIG[7:2]. For LEDSIG[j], where j = 2, 3, ..., 6, the corresponding register is used for programming the LED pin LED_BYTEOUT_[j]. The format is as follows: 4 0 7 3 COL FDX SP1 SP0 COL FDX SP1 SP0 Bits [3:0]Signal polarity: 0: do not invert polarity (high true) 1: invert polarity Bits [7:4]Signal select: 0: do not select 1: select the corresponding bit For j = 2, 3, ..., 5, the value of LED_BYTEOUT_[j] equals the logical AND of all selected bits. For j = 6, the value is equal to the logical OR. Therefore, the programmable LEDSIG[5:2] registers allow any conjunctive formula including any of the 4 status bits (COL, FDX, SP1, SP0) or their negations to be sent to the LED_BYTEOUT_[5:2] pins. Similarly, the programmable LEDSIG[6] register allows any disjunctive formula including any of the 4 status bits or their negations to be sent to pin LED_BYTEOUT_[6]. LEDSIG[7] is used for programming both LED_BYTEOUT_[1] and LED_BYTEOUT_[0]. As we will see, it has other functions as well. The format is as follows: 4 0 7 3 GP RxD TxD FC P6 RxD TxD FC Bits [7] * Global output polarity: this bit controls the output polarity of all LED_BYTEOUT_ and LED_PORT_SEL pins. (Default 0) - 0: do not invert polarity (LED_BYTEOUT_[7:0] are high activated; LED_PORT_SEL[9:0] are low activated) - 1: invert polarity (LED_BYTEOUT_[7:0] are low activated; LED_PORT_SEL[9:0] are high activated) 34 Zarlink Semiconductor Inc. Data Sheet Bits [6:4] * Signal select: - 0: do not select - 1: select the corresponding bit * Bit [3] * MVTX2804 The value of LED_BYTEOUT_[1] equals the logical OR of all selected bits. (Default 110) Polarity control of LED_BYTEOUT_[6](Default 0) - 0: do not invert - 1: invert Bits [2:0] * Signal select: - 0: do not select - 1: select the corresponding bit * The value of LED_BYTEOUT_[0] equals the logical OR of all selected bits. (Default 001) 10.0 10.1 Hardware Statistics Counter Hardware Statistics Counters List MVTX2804 hardware provides a full set of statistics counters for each Ethernet port. The CPU accesses these counters through the CPU interface. All hardware counters are rollover counters. When a counter rolls over, the CPU is interrupted, so that long-term statistics may be kept. The MAC detects all statistics, except for the delay exceed discard counter (detected by buffer manager) and the filtering counter (detected by queue manager). The following is the wrapped signal sent to the CPU through the command block. 31 30 26 25 Status Wrapped Signal B[0] B[1] B[2] B[3] B[4] B[5] B[6] B[7] B[8] B[9] B[10] B[11] B[12] B[13] B[14] B[15] B[16] B[17] B[18] B[19] B[20] B[21] B[22] 0-d 1-L 1-U 2-I 2-u 3-d 4-d 5-d 6-L 6-U 7-l 7-u 8-L 8-U 9-L 9-U A-l A-u B-l B-u C-l C-U1 C-U Bytes Sent (D) Unicast Frame Sent Frame Send Fail Flow Control Frames Sent Non-Unicast Frames Sent Bytes Received (Good and Bad) (D) Frames Received (Good and Bad) (D) Total Bytes Received (D) Total Frames Received Flow Control Frames Received Multicast Frames Received Broadcast Frames Received Frames with Length of 64 Bytes Jabber Frames Frames with Length Between 65-127 Bytes Oversize Frames Frames with Length Between 128-255 Bytes Frames with Length Between 256-511 Bytes Frames with Length Between 512-1023 Bytes Frames with Length Between 1024-1528 Bytes Fragments Alignment Error Undersize Frames 0 Zarlink Semiconductor Inc. 35 MVTX2804 B[23] B[24] B[25] B[26] B[27] B[28] B[29] B[30] B[31] D-l D-u E-l E-u F-l F-U1 F-U CRC Short Event Collision Drop Filtering Counter Delay Exceed Discard Counter Late Collision Link Status Change Current link status Data Sheet Notation: X-Y X: Address in the contain memory Y: Size and bits for the counter d: L: U: U1: l: u: D Word counter 24 bits counter bit[23:0] 8 bits counter bit[31:24] 8 bits counter bit[23:16] 16 bits counter bit[15:0] 16 bits counter bit[31:16] 10.2 10.2.1 10.2.1.1 IEEE 802.3 HUB Management (RFC 1213) Event Counters READABLEOCTET Counts number of bytes (i.e. octets) contained in good valid frames received. Frame size: 64 bytes,< 1522 bytes if VLAN Tagged; 1518 bytes if not VLAN Tagged No FCS (i.e. checksum) error No collisions 10.2.1.2 READABLEFRAME Counts number of good valid frames received. Frame size: 64 bytes,< 1522 bytes if VLAN Tagged; 1518 bytes if not VLAN Tagged No FCS error No collisions 10.2.1.3 FCSERRORS Counts number of valid frames received with bad FCS. Frame size: 64 bytes, 1522 bytes if VLAN Tagged; 1518 bytes if not VLAN Tagged No framing error 36 Zarlink Semiconductor Inc. Data Sheet No collisions MVTX2804 10.2.1.4 ALIGNMENTERRORS Counts number of valid frames received with bad alignment (not byte-aligned). Frame size: 64 bytes, 1522 bytes if VLAN Tagged; 1518 bytes if not VLAN Tagged No framing error No collisions 10.2.1.5 FRAMETOOLONGS Counts number of frames received with size exceeding the maximum allowable frame size. Frame size: 64 bytes, 1522 bytes if VLAN Tagged; 1518 bytes if not VLAN Tagged FCS error:don't care Framing error:don't care No collisions 10.2.1.6 SHORTEVENTS Counts number of frames received with size less than the length of a short event. Frame size: 64 bytes, 10 bytes FCS error:don't care Framing error:don't care No collisions 10.2.1.7 RUNTS Counts number of frames received with size under 64 bytes, but greater than the length of a short event. Frame size: 10 bytes, 64 bytes FCS error:don't care Framing error:don't care No collisions 10.2.1.8 COLLISIONS Counts number of collision events. Frame size:any size 10.2.1.9 LATEEVENTS Counts number of collision events that occurred late (after LateEventThreshold = 64 bytes). Frame size:any size Events are also counted by collision counter Zarlink Semiconductor Inc. 37 MVTX2804 10.2.1.10 VERYLONGEVENTS Counts number of frames received with size larger than Jabber Lockup Protection Timer (TW3). Frame size:> Jabber Data Sheet 10.2.1.11 DATARATEMISATCHES For repeaters or HUB application only. 10.2.1.12 AUTOPARTITIONS For repeaters or HUB application only. 10.2.1.13 TOTALERRORS Sum of the following errors: FCS errors Alignment errors Frame too long Short events Late events Very long events 10.3 10.3.1 10.3.1.1 IEEE - 802.1 Bridge Management (RFC 1286) Event Counters INFRAMES Counts number of frames received by this port or segment. Note: this counter only counts a frame received by this port if and only if it is for a protocol being processed by the local bridge function. 10.3.1.2 OUTFRAMES Counts number of frames transmitted by this port. Note: this counter only counts a frame transmitted by this port if and only if it is for a protocol being processed by the local bridge function. 10.3.1.3 INDISCARDS Counts number of valid frames received which were discarded (i.e., filtered) by the forwarding process. 10.3.1.4 DELAYEXCEEDEDDISCARDS Counts number of frames discarded due to excessive transmit delay through the bridge. 10.3.1.5 MTUEXCEEDEDDISCARDS Counts number of frames discarded due to excessive size. 38 Zarlink Semiconductor Inc. Data Sheet 10.4 10.4.1 10.4.1.1 RMON - Ethernet Statistic Group (RFC 1757) Event Counters DROP EVENTS MVTX2804 Counts number of times a packet is dropped, because of lack of available resources. DOES NOT include all packet dropping -- for example, random early drop for quality of service support. 10.4.1.2 OCTETS Counts the total number of octets (i.e. bytes) in any frames received. 10.4.1.3 BROADCASTPKTS Counts the number of good frames received and forwarded with broadcast address. Does not include non-broadcast multicast frames. 10.4.1.4 MULTICASTPKTS Counts the number of good frames received and forwarded with multicast address. Does not include broadcast frames. 10.4.1.5 CRCALIGNERRORS Frame size: 64 bytes,< 1522 bytes if VLAN tag (1518 if no VLAN) No collisions: Counts number of frames received with FCS or alignment errors 10.4.1.6 UNDERSIZEPKTS Counts number of frames received with size less than 64 bytes. Frame size:< 64 bytes, No FCS error No framing error No collisions 10.4.1.7 OVERSIZEPKTS Counts number of frames received with size exceeding the maximum allowable frame size. Frame size:>1522 bytes if VLAN tag (1518 bytes if no VLAN) FCS errordon't care Framing errordon't care No collisions 10.4.1.8 FRAGMENTS Counts number of frames received with size less than 64 bytes and with bad FCS. Zarlink Semiconductor Inc. 39 MVTX2804 Frame size:< 64 bytes Framing error don't care No collisions Data Sheet 10.4.1.9 JABBERS Counts number of frames received with size exceeding maximum frame size and with bad FCS. Frame size:> 1522 bytes if VLAN tag (1518 bytes if no VLAN) Framing errordon't care No collisions 10.4.1.10 COLLISIONS Counts number of collision events detected. Only a best estimate since collisions can only be detected while in transmit mode, but not while in receive mode. Frame size:any size 10.4.1.11 PACKET COUNT FOR DIFFERENT SIZE GROUPS Six different size groups - one counter for each: Pkts64Octetsfor any packet with size = 64 bytes Pkts65to127Octetsfor any packet with size from 65 bytes to 127 bytes Pkts128to255Octetsfor any packet with size from 128 bytes to 255 bytes Pkts256to511Octetsfor any packet with size from 256 bytes to 511 bytes Pkts512to1023Octetsfor any packet with size from 512 bytes to 1023 bytes Pkts1024to1518Octetsfor any packet with size from 1024 bytes to 1518 bytes counts both good and bad packets. Miscellaneous Counters In addition to the statistics groups defined in previous sections, the MVTX2804 has other statistics counters for its own purposes. We have two counters for flow control - one counting the number of flow control frames received, and another counting the number of flow control frames sent. We also have two counters, one for unicast frames sent, and one for non-unicast frames sent. A broadcast or multicast frame qualifies as non-unicast. Furthermore, we have a counter called "frame send fail." This keeps track of FIFO under-runs, late collisions, and collisions that have occurred 16 times. 40 Zarlink Semiconductor Inc. Data Sheet 11.0 11.1 MVTX2804 Register Definition Register Description Register Description CPU Addr (Hex) 000 + 2N 001 + 2N 010 011 012 013 014 015 016 100 101 102 + 4N 103 + 4N 105 + 4N 126 200 201 202 203 204 205 R/W I2C Addr (Hex) 000+2N 001+2N 010 011 N/A N/A N/A N/A N/A 012 013 014+4N 015+4N 017+4N 038 NA NA NA NA NA NA Default Notes 0. ETHERNET Port Control Registers - Substitute [N] with Port number (0..7) ECR1P"N" ECR2P"N" ECRMISC1 ECRMISC2 GGCONTROL0 GGCONTROL1 GGCONTROL2 GGCONTROL3 ACTIVELINK AVTCL AVTCH PVMAP"N"_0 PVMAP"N"_1 PVMAP"N"_3 PVMODE TRUNK0 TRUNK1 TRUNK2 TRUNK3 SINGLE_RING TRUNK_RING Port Control Register 1 for Port N (N=0-7) Port Control Register 2 for Port N (N=0-7) Port Control Misc1 Port Control Misc 2 Extra Gigabit Port Control -port 0,1 Extra Gigabit Port Control -port 2,3 Extra Gigabit Port Control -port 4,5 Extra Gigabit Port Control -port 6,7 Active Link status port 7:0 VLAN Type Code Register Low VLAN Type Code Register High Port "N" Configuration Register 0 (N=0-8) Port "N" Configuration Register 1 (N=0-8) Port "N" Configuration Register 3 (N=0-8) VLAN Operating Mode Trunk group 0 Member Trunk group 1 Member Trunk group 2 Member Trunk group 3 Member Single ring port map Trunk ring port map R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W c0 00 c0 00 00 00 00 00 00 00 81 ff ef 00 00 00 00 00 00 Reserved Reserved 1. VLAN Control Registers - Substitute [N] with Port number (0..8) 2. TRUNK Control Registers Zarlink Semiconductor Inc. 41 MVTX2804 CPU Addr (Hex 206 207 208 209 20A 20B 20C 20D 20E 20F 210 211 212 213 214 215 216 217 218 219 21A 21B I2C Addr (Hex) NA 039 NA NA NA NA NA NA 03A NA NA NA NA NA NA NA NA NA NA NA NA NA Data Sheet Register TRUNK_HASH_M ODE TRUNK0_MODE TRUNK0_HASH0 TRUNK0_HASH1 TRUNK0_HASH2 TRUNK0_HASH3 TRUNK0_HASH4 TRUNK0_HASH5 TRUNK1_MODE TRUNK1_HASH0 TRUNK1_HASH1 TRUNK1_HASH2 TRUNK1_HASH3 TRUNK1_HASH4 TRUNK1_HASH5 TRUNK2_HASH0 TRUNK2_HASH1 TRUNK2_HASH2 TRUNK2_HASH3 TRUNK2_HASH4 TRUNK2_HASH5 TRUNK3_HASH0 Description Trunk hash mode Trunk Group 0 Mode Trunk Group 0 Hash 0, 1, 2 Destination Port Trunk Group 0 Hash 2, 3, 4, 5 Destination Port Trunk Group 0 Hash 5, 6, 7 Destination Port Trunk Group 0 Hash 8, 9, 10 Destination Port Trunk Group 0 Hash 10, 11, 12, 13 Destination Port Trunk Group 0 Hash 13, 14, 15 Destination Port Trunk Group 1 Mode Trunk Group 1 Hash 0, 1, 2 Destination Port Trunk Group 1 Hash 2, 3, 4, 5 Destination Port Trunk Group 1 Hash 5, 6, 7 Destination Port Trunk Group 1 Hash 8, 9, 10 Destination Port Trunk Group 1 Hash 10, 11, 12, 13 Destination Trunk Group 1 Hash 13, 14, 15 Destination Trunk Group 2 Hash 0, 1, 2 Destination Port Trunk Group 2 Hash 2, 3, 4, 5 Destination Port Trunk Group 2 Hash 5, 6, 7 Destination Port Trunk Group 2 Hash 8, 9, 10 Destination Port Trunk Group 2 Hash 10, 11, 12, 13 Destination Port Trunk Group 2 Hash 13, 14, 15 Destination Port Trunk Group 3 Hash 0, 1, 2 Destination Port R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Default 00 00 08 82 20 08 82 20 00 08 82 20 08 82 20 2c cb b2 2c cb b2 2c Notes 42 Zarlink Semiconductor Inc. Data Sheet CPU Addr (Hex 21C 21D 21E 21F 220 221 222 223 224 225 226 227 228 229 22A 22B 22C 22D 22E 22F 230 231 I2C Addr (Hex) NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA MVTX2804 Description Trunk Group 3 Hash 2, 3, 4, 5 Destination Port Trunk Group 3 Hash 5, 6, 7 Destination Port Trunk Group 3 Hash 8, 9, 10 Destination Port Trunk Group 3 Hash 10, 11, 12, 13 Destination Port Trunk Group 3 Hash 13, 14, 15 Destination Port Multicast hash result 0 mask bit[7:0] Multicast hash result 1 mask bit[7:0] Multicast hash result 2 mask bit[7:0] Multicast hash result 3 mask bit[7:0] Multicast hash result 4 mask bit[7:0] Multicast hash result 5 mask bit[7:0] Multicast hash result 6 mask bit[7:0] Multicast hash result 7 mask bit[7:0] Multicast hash result 8 mask bit[7:0] Multicast hash result 9 mask bit[7:0] Multicast hash result 10 mask bit[7:0] Multicast hash result 11 mask bit[7:0] Multicast hash result 12 mask bit[7:0] Multicast hash result 13 mask bit[7:0] Multicast hash result 14 mask bit[7:0] Multicast hash result 15 mask bit[7:0] Multicast hash bit[8] for result 7-0 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Default cb b2 2c Bc b2 ff ff ff ff ff ff ff ff ff fff ff ff ff ff ff ff ff Notes Register TRUNK3_HASH1 TRUNK3_HASH2 TRUNK3_HASH3 TRUNK3_HASH4 TRUNK3_HASH5 Multicast_HASH00 Multicast_HASH01 Multicast_HASH02 Multicast_HASH03 Multicast_HASH04 Multicast_HASH05 Multicast_HASH06 Multicast_HASH07 Multicast_HASH08 Multicast_HASH09 Multicast_HASH10 Multicast_HASH11 Multicast_HASH12 Multicast_HASH13 Multicast_HASH14 Multicast_HASH15 Multicast_HASHML Zarlink Semiconductor Inc. 43 MVTX2804 CPU Addr (Hex 232 I2C Addr (Hex) NA Data Sheet Register Description R/W R/W Default ff Notes Multicast_HASHMH Multicast hash bit[8] for result 15-8 3. CPU Port Configuration MAC0 MAC1 MAC2 MAC3 MAC4 MAC5 INT_MASK0 INT_MASK1 INT_MASK2 INT_MASK3 INT_STATUS0 INT_STATUS1 INTP_MASK"N" RQS RQSS TX_AGE CPU MAC Address byte 0 CPU MAC Address byte 1 CPU MAC Address byte 2 CPU MAC Address byte 3 CPU MAC Address byte 4 CPU MAC Address byte 5 Interrupt Mask 0 Interrupt Mask 1 Interrupt Mask 2 Interrupt Mask 3 Status of Masked Interrupt Register0 Status of Masked Interrupt Register1 Interrupt Mask for MAC Port 2n, 2n+1 ( n=0-3) Receive Queue Select Receive Queue Status Transmission Queue Aging Time MAC Address Aging Time Low MAC Address Aging Time High VLAN to Port Aging Time Search Engine operation mode Scan Control Register FCB Aging Timer QOS Control Flooding Control Register VLAN Priority Map Low VLAN Priority Map Middle VLAN Priority Map High TOS Priority Map Low 300 301 302 303 304 305 306 307 308 309 30A 30B 30C-30F 310 311 312 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W RO RO R/W R/W RO R/W NA NA NA NA NA NA NA NA NA NA NA NA NA NA 03B NA 00 00 00 00 00 ff ff ff ff 00 ff 00 08 4. Search Engine Configurations AGETIME_LOW AGETIME_HIGH V_AGETIME SE_OPMODE SCAN FCBAT QOSC FCR AVPML AVPMM AVPMH TOSPML 400 401 402 403 404 500 501 502 503 504 505 506 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W 03C 03D NA NA NA 03E 03F 040 041 042 043 044 2c 00 ff 00 00 ff 00 08 88 c6 fa 88 5. Buffer Control and QOS Control 44 Zarlink Semiconductor Inc. Data Sheet CPU Addr (Hex 507 508 509 50A 50B 50C 50D 50E 50F 510 511 512 513 514 515 516 517-546 547-599 59A 59B 600 601 602 603 604 605 606 607 608 609 60B 60C 60D I2C Addr (Hex) 045 046 047 048 049 04A 04B 04C 04D 04E 04F 050 051 052 053 054 055-084 NA 085 086 0B1 0B2 0B3 N/A N/A N/A N/A N/A N/A 0B4 0C5 0BB 0BC 8e 68 00 00 10 00 00 00 00 00 00 38 00 00 00 MVTX2804 Description TOS Priority Map Middle TOS Priority Map High VLAN Discard Map TOS Discard Map Broadcast/Multicast Rate Control Unicast Congestion Control Multicast Congestion Control Port Reservation for 10/100 Ports Port Reservation for Giga Ports Share FCB Size Class 2 Reserved Size Class 3 Reserved Size Class 4 Reserved Size Class 5 Reserved Size Class 6 Reserved Size Class 7 Reserved Size QOS Control (N=0 - 2F) QOS Control (N=30 - 82) WRED Rate Control 0 WRED Rate Control 1 MII Register Option 0 MII Register Option 1 Feature Registers MII Command Register 0 MII Command Register 1 MII Command Register 2 MII Command Register 3 MII Data Register 0 MII Data Register 1 LED Control Register EEPROM Checksum Register LED User Define Register 0 LED User Define Register 1 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W RO RO R/W R/W R/W R/W Default c6 fa 00 00 00 07 48 00 26 37 00 00 00 00 00 00 Notes Register TOSPMM TOSPMH AVDM TOSDML BMRC UCC MCC PR100 PRG SFCB C2RS C3RS C4RS C5RS C6RS C7RS QOSC"N" QOSC"N" RDRC0 RDRC1 MII_OP0 MII_OP1 FEN MIIC0 MIIC1 MIIC2 MIIC3 MIID0 MIID1 LED CHECKSUM LEDUSER0 LEDUSER1 6. MISC Configuration Registers Zarlink Semiconductor Inc. 45 MVTX2804 CPU Addr (Hex 60E 60F 610 611 612 613 614 615 I2C Addr (Hex) 0BD 0BE 0BF 0C0 0C1 0C2 0C3 0C4 Data Sheet Register LEDUSER2 LEDUSER3 LEDUSER4 LEDUSER5 LEDUSER6 LEDUSER7 MIINP0 MIINP1 Description LED User Define Reg. 2/LED_byte pin 2 LED User Define Reg. 3/LED_byte pin 3 LED User Define Reg. 4/LED_byte pin 4 LED User Define Reg. 5/LED_byte pin 5 LED User Define Reg. 6/LED_byte pin 6 LED User Define Reg. 7/LED_byte pin 1 & 0 MII NEXT PAGE DATA REGISTER0 MII NEXT PAGE DATA REGISTER1 Test Register Low Test Register Medium Test Register High TEST MUX read back register [7:0] TEST MUX read back register [15:8] Test Counter Register MASK Timeout 0 MASK Timeout 1 MASK Timeout 2 MASK Timeout 3 MASK Timeout 4 Global Control Register Device Status and Signature Register Gigabit Port0 Port1 Status Register Gigabit Port2 Port3 Status Register Gigabit Port4 Port5 Status Register Gigabit Port6 Port7 Status Register R/W R/W R/W R/W R/W R/W R/W R/W R/W Default 80 33 32 20 40 61 00 00 Notes E. Test Group Control DTSRL DTSRM DTSRH TDRB0 TDRB1 DTCR MASK0 MASK1 MASK2 MASK3 MASK4 GCR DCR DCR01 DCR23 DCR45 DCR67 E00 E01 E02 E03 E04 E05 E06 E07 E08 E09 E0A F00 F01 F02 F03 F04 F05 R/W R/W R/W RO RO R/W R/W R/W R/W R/W R/W R/W RO RO RO RO RO N/A N/A N/A N/A N/A N/A 0B6 0B7 0B8 0B9 0BA N/A N/A NA NA NA NA 00 00 00 00 00 00 00 00 01 00 F. Device Configuration Register 46 Zarlink Semiconductor Inc. Data Sheet CPU Addr (Hex F06 F07 F08 F09 F0A F0B F0C F0D F0E F0F F10 FFF I2C Addr (Hex) N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A DA MVTX2804 Description Device Port Status Register Data read back register PLL Control Register LCLK Control Register BCLK Control Register BOOT STRAP read back register 0 BOOT STRAP read back register 1 BOOT STRAP read back register 2 BOOT STRAP read back register 3 BOOT STRAP read back register 4 BOOT STRAP read back register 5 DA Register R/W R/W RO R/W R/W R/W RO RO RO RO RO RO RO Default 00 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Notes Register DPST DTST PLLCR LCLKCR BCLKCR BSTRRB0 BSTRRB1 BSTRRB2 BSTRRB3 BSTRRB4 BSTRRB5 DA Note Note Note Note Note 1: 2: 3: 4: 5: 1. 2. 3. 4. 5. se = Search Engine fe = Frame Engine pgs = Port Group01, 23, 45, and 67 mc = MAC Control tm = timer 11.2 11.2.1 * * * * * * Directly Accessed Registers INDEX_REG0 Address bits [7:0] for indirectly accessed register addresses Address = 0 (write only) 11.2.2 INDEX_REG1 (only needed for CPU 8-bit bus mode) Address bits [15:8] for indirectly accessed register addresses Address = 1 (write only) 11.2.3 DATA_FRAME_REG Data of indirectly accessed registers. (8 bits) Address = 2 (read/write) 11.2.4 CONTROL_FRAME_REG * CPU transmit/receive switch frames. (8/16 bits) * Address = 3 (read/write) * Format: (see processor interface application note for more information) - Send frame from CPU: (In sequence) Frame Data (size should be in multiple of 8-byte) 8-byte of Frame status (Frame size, Destination port #, Frame O.K. status) Zarlink Semiconductor Inc. 47 MVTX2804 - CPU Received frame: (In sequence) 8-byte of Frame status (Frame size, Source port #, VLAN tag) Frame Data Data Sheet 11.2.5 * * * COMMAND&STATUS CPU interface commands (write) and status Address = 4 (read/write) When the CPU reads this register: Bit [0]: Transmit Control Command 1 Ready; Must read true before CPU writes new Control Command 1. Bit [1]: Receive Control Command 1 Ready; Must read true before CPU reads a new Control Command 1. Bit [2]: Receive Control Command 2 Ready; Must read true before CPU reads a new Control Command 2. Bit [3]: Receive CPU Frame Ready; Must read true before receiving a CPU frame and at every 8-byte boundary within a CPU frame. * Bit [4]: Transmit CPU Frame Ready; Must read true before transmitting a CPU frame and at every 16-byte boundary within a CPU frame. * Bit [5]: End of Receive CPU Frame to indicate that the last 8 bytes need to be read. * Bit [15:6]: Reserved. * * * * * When the CPU writes to this register: * Bit [0]: End of Transmit Control Command indicator; Set after CPU writes a Control Command Frame into Rx buffer. * Bit [1]: End of Receive Control Command 1 indicator; Set after CPU reads out a Control Command 1 Frame from Tx buffer 1. * Bit [2]: End of Receive Control Command 2 indicator; Set after CPU reads out a Control Command 2 Frame from Tx buffer 2. * Bit [3]: End of Receive CPU Frame indicator. Set after CPU reads out a CPU frame or to flush out the rest of CPU frame. * Bit [4]: End of Transmit CPU Frame indicator. Set before writing the last byte of CPU frame. * Bit [7:5]: Reserved and always write 0's. * Bit [15:8]: Reserved and write 0's in 16-bit mode. 11.2.6 * * * Bit Bit Bit Bit Bit Interrupt Register Interrupt sources (8 bits) Address = 5 (read only) When CPU reads this register [0]: *CPU frame interrupt [1]:*Control Frame 1 interrupt. Control Frame receive buffer1 has data for CPU to read [2]:*Control Frame 2 interrupt. Control Frame receive buffer2 has data for CPU to read [3]**From any of the gigabit port interrupt [7:4]:*Reserve Note: This register is not self-cleared. After reading CPU has to clear the bit writing 0 to it 11.2.7 * * * Control Frame Buffer1 Access Register Address = 6 (read/write) When CPU writes to this register, data is written to the Control Command Frame Receive Buffer When CPU reads this register, data is read from the Control Command Frame Transmit Buffer1 48 Zarlink Semiconductor Inc. Data Sheet 11.2.8 * * MVTX2804 Control Frame Buffer2 Access Register Address = 7 (read only) When CPU reads this register, data is read from the Control Command Frame transmit Buffer 2 Indirectly Accessed Registers 11.3 11.3.1 11.3.1.1 * * Group 0 Address MAC Ports Group ECR1PN: PORT N CONTROL REGISTER I2C Address h00+2n; CPU Address:h000+2n (n=0 to 7) Accessed by CPU, serial interface and I2C (R/W) 7 Sp State 6 5 A-FC 4 3 2 1 Port Mode 0 Bit [4:0] Bit [4:3] * Port Mode (Default 2'b00) * 00 - Automatic Enable Auto-Negotiation - This enables hardware state machine for auto-negotiation. * 01 - Limited Disable auto-Negotiation - This disables hardware auto-negotiation. Hardware only Polls MII for link status. Use bit [2:0] for config. * 10 - Link Down - Force link down (disable the port). Does not talk to PHY. * 11 - Link Up - Does not talk to PHY. User ERC1 [2:0] for config. * 1 - 10Mbps (Default 1'b0) * 0 - 100Mbps Bit [2] Bit 2 is used only when the port is in MII mode. Bit [1] Bit [0] * 1 - Half Duplex (Do not use) (Default 1'b0) * 0 - Full Duplex * 1 - Flow Control Off (Default 1'b0) * 0 - Flow Control On * When flow control is on: * In full duplex mode, the MAC transmitter sends Flow Control Frames when necessary. The MAC receiver interprets and processes incoming flow control frames. The Flow Control Frame Received counter is incremented whenever a flow control frame is received. * When flow control is off: * In full duplex mode, the MAC transmitter does not send flow control frames. The MAC receiver does not interpret or process the flow control frames. The Flow Control Frame Receiver counter is not incremented. Zarlink Semiconductor Inc. 49 MVTX2804 Bit [5] * Asymmetric Flow Control Enable. * 0 - Disable asymmetric flow control * 1 - Enable asymmetric flow control Data Sheet * When this bit is set, and flow control is on (bit[0] = 0), don't send out a flow control frame. But MAC receiver interprets and process flow control frames. (Default is 0) SS - Spanning tree state (802.1D spanning tree protocol). (Default 2'b11) * * * * 00 - Blocking: Frame is dropped 01 - Listening: Frame is dropped 10 - Learning: Frame is dropped. Source MAC address is learned. 11 - Forwarding: Frame is forwarded. Source MAC address is learned. Bit [7:6] * 11.3.1.2 * * I2C ECR2PN: PORT N CONTROL REGISTER Address: 01+2n; CPU Address:h001+2n (n=0to7) Accessed by CPU and serial interface (R/W): 7 Security EN Bit[0] * Filter untagged frame (Default 0) * 0: Disable * 1: Enable - All untagged frames from this port are discarded or follow security option when security is enable 6 5 3 2 DisL 1 Ftf 0 Futf Bit[1] * Filter Tag frame (Default 0) * 0: Disable * 1: Enable - All tagged frames from this port are discarded or follow security option when security is enable Bit[2] * Learning Disable (Default 0) * 0: Learning is enabled on this port * 1: Learning is disabled on this port Bit [5:3:] * Reserved 50 Zarlink Semiconductor Inc. Data Sheet Bit[7:6] * MVTX2804 Security Enable (Default 00). The MVTX2804 checks the incoming data for one of the following conditions: 1. If the source MAC address of the incoming packet is in the MAC table and is defined as secure address but the ingress port is not the same as the port associated with the MAC address in the MAC table. A MAC address is defined as secure when its entry at MAC table has static status and bit 0 is set to 1. MAC address bit 0 (the first bit transmitted) indicates whether the address is unicast or multicast. As source addresses are always unicast bit 0 is not used (always 0). MVTX2804 uses this bit to define secure MAC addresses. 2. If the port is set as learning disable and the source MAC address of the incoming packet is not defined in the MAC address table. 3. If the port is configured to filter untagged frames and an untagged frame arrives or if the port is configured to filter tagged frames and a tagged frame arrives. If one of these three conditions occurs, the packet will be handled according to one of the following specified options: * CPU installed * * * * 00 - Disable port security 01 - Discard violating packets 10 - Send packet to CPU and destination port 11 - Send packet to CPU only * CPU not installed * 00 - Disable port security * 01 - Enable port security. Port will be disabled when security violation is detected * 10 - N/A * 11 - N/A 11.3.1.3 * * ECRMISC1 - CPU PORT CONTROL REGISTER MISC1 I2C Address h10, CPU Address:h010 Access by CPU, serial interface and I2C (R/W) 7 SS state Bit [5:0] Bit [7:6] * * Reserved SS - Spanning tree state (802.1D spanning tree protocol). (Default 2'b11) * * * * 00 - Blocking: Frame is dropped 01 - Listening: Frame is dropped 10 - Learning: Frame is dropped. Source MAC address is learned. 11 - Forwarding: Frame is forwarded. Source MAC address is learned. 6 5 Reserved 0 Zarlink Semiconductor Inc. 51 MVTX2804 11.3.1.4 * * Data Sheet ECRMISC2 - CPU PORT CONTROL REGISTER MISC2 (I2C Address h11, CPU Address:h011) Access by CPU, serial interface and I2C (R/W) 7 Security EN Bit [0] * Filter untagged frame (Default 0) * 0: Disable * 1: Enable - All untagged frames from the CPU are discarded or follow security option when security is enable Security does not make much sense for CPU! 6 5 3 2 DisL 1 Ftf Futf 0 Bit[1] * Filter Tagged frame (Default 0) * 0: Disable * 1: Enable - All tagged frames from the CPU are discarded or follow security option when security is enable Security does not make much sense for CPU! Bit[2] * Learning Disable (Default 0) * 1 - Learning is disabled on this port * 0 - Learning is enabled on this port Bit [5:3] Bit[7:6] * * * Reserved (Default 0) Security Enable (Default 2'b00) CPU installed * * * * 00 - Disable port security 01 - Discard violation packet 10 - Send packet to CPU and port 11 - Send packet to CPU only 11.3.1.5 * * GGCONTROL 0- EXTRA GIGA PORT CONTROL CPU Address:h012 Accessed by CPU and serial interface (R/W) 7 6 5 MII1 Bit[0]: * 4 Rst1 3 2 1 MII0 0 Rst0 Reset GIGA port 0 Default is 0 * 0: Normal operation * 1: Reset Gigabit port 0. Example: used when a new Why is connected (Hot swap) Bit[1]: * GIGA port 0 use MII interface (10/100M) Default is 0 * 0: Gigabit port operation at 1000M mode * 1: Gigabit port operation at 10/100M mode (MII) Bit[3:2]: Bit[4]: * * Reserved - Must be '0' Reset GIGA port 1 Default is 0 * 0: Normal operation * 1: Reset Gigabit port 1. Example: used when a new Phy is connected (Hot swap) 52 Zarlink Semiconductor Inc. Data Sheet Bit[5]: * GIGA port 1 use MII interface (10/100M) Default is 0 * 0: Gigabit port operation at 1000M mode * 1: Gigabit port operation at 10/100M mode (MII) MVTX2804 Bit[7:6]: * Reserved - Must be '0' 11.3.1.6 * * GGCONTROL 1- EXTRA GIGA PORT CONTROL CPU Address:h013 Accessed by CPU and serial interface (R/W) 7 6 5 MII3 Bit[0]: * 4 Rst3 3 2 1 MII2 0 Rst2 Reset GIGA port 2 Default is 0 * 0: Normal operation * 1: Reset Gigabit port 2. Example: used when a new Phy is connected (Hot swap) Bit[1]: * GIGA port 2 use MII interface (10/100M) Default is 0 * 0: Gigabit port operation at 1000M mode * 1: Gigabit port operation at 10/100M mode (MII) Bit[3:2]: Bit[4]: * * Reserved - must be '0' Reset GIGA port 3 Default is 0 * 0: Normal operation * 1: Reset Gigabit port 3. Example: used when a new Phy is connected (Hot swap) Bit[5]: * GIGA port 3 use MII interface (10/100M) Default is 0 * 0: Gigabit port operation at 1000M mode * 1: Gigabit port operation at 10/100M mode (MII) Bit[7:6]: * Reserved - Must be '0' 11.3.1.7 * * GGCONTROL 2- EXTRA GIGA PORT CONTROL CPU Address:h014 Accessed by CPU and serial interface (R/W) 7 6 5 MII5 Bit[0]: * 4 Rst5 3 2 1 MII4 0 Rst4 Reset GIGA port 4 Default is 0 * 0: Normal operation * 1: Reset Gigabit port 4. Example: used when a new Phy is connected (Hot swap) Bit[1]: * GIGA port 4 use MII interface (10/100M) Default is 0 * 0: Gigabit port operation at 1000M mode * 1: Gigabit port operation at 10/100M mode (MII) Bit[3:2]: * Reserved - Must be '0 Zarlink Semiconductor Inc. 53 MVTX2804 Bit[4]: * Reset GIGA port 5 Default is 0 Data Sheet * 0: Normal operation * 1: Reset Gigabit port 5. Example: used when a new Phy is connected (Hot swap) Bit[5] * GIGA port 5 use MII interface (10/100M) Default is 0 * 0: Gigabit port operation at 1000M mode * 1: Gigabit port operation at 10/100M mode (MII) Bit[7:6]: * Reserved - Must be '0' 11.3.1.8 * * GGCONTROL 3- EXTRA GIGA PORT CONTROL CPU Address:h015 Accessed by CPU and serial interface (R/W) 7 6 5 MII7 Bit[0]: * 4 Rst7 3 2 1 MII6 0 Rst6 Reset GIGA port 6 Default is 0 * 0: Normal operation * 1: Reset Gigabit port 6. Example: used when a new Phy is connected (Hot swap) Bit[1]: * GIGA port 6 use MII interface (10/100M) Default is 0 * 0: Gigabit port operation at 1000M mode * 1: Gigabit port operation at 10/100M mode (MII) Bit[3:2]: Bit[4]: * * Reserved - Must be '0 Reset GIGA port 7 Default is 0 * 0: Normal operation * 1: Reset Gigabit port 7. Example: used when a new Phy is connected (Hot swap) Bit[5] * GIGA port 7 use MII interface (10/100M) Default is 0 * 0: Gigabit port operation at 1000M mode * 1: Gigabit port operation at 10/100M mode (MII) Bit[7:6]: * Reserved - Must be '0' 11.4 11.4.1 11.4.1.1 I 2C Group 1 Address VLAN Group AVTCL - VLAN TYPE CODE REGISTER LOW * Address h12; CPU Address:h100 * Accessed by CPU, serial interface and I2C (R/W) Bit[7:0]:VLANType_LOW: Lower 8 bits of the VLAN type code (Default 00) 11.4.1.2 * * Bit AVTCH - VLAN TYPE CODE REGISTER HIGH I2C Address h13; CPU Address:h101 Accessed by CPU, serial interface and I2C (R/W) [7:0] VLANType_HIGH: Upper 8 bits of the VLAN type code (Default is 81) 54 Zarlink Semiconductor Inc. Data Sheet 11.4.1.3 * * MVTX2804 PVMAP00_0 - PORT 00 CONFIGURATION REGISTER 0 I2C Address h14, CPU Address:h102) Accessed by CPU, serial interface and I2C (R/W) In Port Based VLAN Mode This register indicates the legal egress ports. Example: A "1" on bit 7 means that packets arriving on port 0 can be sent to port 7. A "0" on bit 7 means that any packet destined to port 7 will be discarded. Bit[7:0]: * VLAN Mask for ports 7 to 0 (Default FF) * 0 - Disable * 1 - Enable In Tag Based VLAN Mode This is the default VLAN tag. It works with configuration register PVMAP00_1 [7:5] [3:0] to form the default VLAN tag. If the received packed is untagged, it receives the default VLAN tag. If the packet has a VLAN ID of 0, then PVID is used to replace the packet's VLAN. Bit[7:0]: PVID [7:0] (Default is FF) 11.4.1.4 * * PVMAP00_1 - PORT 00 CONFIGURATION REGISTER 1 I2C Address h15, CPU Address:h103 Accessed by CPU, serial interface and I2C (R/W) In Port Based VLAN Mode Bit[7:0]: VLAN Mask for port 8 - CPU port (Default is FF) In Tag Based VLAN Mode 7 5 Unitag Port Priority Bit[3:0]: Bit [4]: * 4 Ultrust 3 PVID 0 PVID [11:8] (Default is F) * Untrusted Port. (Default is 0) This register is used to change the VLAN priority field of a packet to a predetermined priority. * 1: VLAN priority field is changed to Bit[7:5] at ingress port * 0: Keep VLAN priority field Bit [7:5]: * Untag Port Priority (Default 7) Zarlink Semiconductor Inc. 55 MVTX2804 11.4.1.5 PVMAP00_3 - PORT 00 CONFIGURATION REGISTER 3 Data Sheet * I2C Address h17, CPU Address:h105 * Accessed by CPU, serial interface and I2C (R/W) In Port Based Mode 7 FP en Bit [1:0]: Bit [2]: 6 Drop 5 Default TX priority 3 2 FNT 1 IF Reserved 0 Reserved (Default 0) Force untagged out (Default 0) * 0 Disable * 1 Force untag output All packets transmitted from this port are untagged. This register is used when this port is connected to legacy equipment that does not support VLAN tagging. Bit [5:3]: Fixed Transmit priority. Used when bit[7] = 1 (Default 0) * * * * * * * * 000 001 010 011 100 101 110 111 Transmit Priority Level 0 (Lowest) Transmit Priority Level 1 Transmit Priority Level 2 Transmit Priority Level 3 Transmit Priority Level 4 Transmit Priority Level 5 Transmit Priority Level 6 Transmit Priority Level 7 (Highest) Bit [6]: Fixed Discard priority (Default 0) * 0 - Discard Priority Level 0 (Lowest) * 1 - Discard Priority Level 7(Highest) Bit [7]: Enable Fix Priority (Default 0) * 0 Disable fix priority. All frames are analyzed. Transmit Priority and Drop Priority are based on VLAN Tag or TOS. * 1 Transmit Priority and Discard Priority are based on values programmed in bit [6:3] In Tag based VLAN Mode Bit [1]: Ingress filter enable (Default 1) * 0 Disable - Ingress filter. Packets with VLAN not belonging to source port are forwarded if destination port belongs to the VLAN. Symmetric VLAN. * Enable - Packets are discarded when source port is not a VLAN member. Asymmetric VLAN. Bit [2]: Force untagged out (Default 1). * 0 Disable * 1 Force untagged output. All packets transmitted from this port are untagged. This register is used when this port is connected to legacy equipment that does not support VLAN tagging. 56 Zarlink Semiconductor Inc. Data Sheet Bit [5:3]: Fixed Transmit priority (Default 0) Used When Bit [7] = 1 * * * * * * * * 000 001 010 011 100 101 110 111 Transmit Priority Level 0 (Lowest) Transmit Priority Level 1 Transmit Priority Level 2 Transmit Priority Level 3 Transmit Priority Level 4 Transmit Priority Level 5 Transmit Priority Level 6 Transmit Priority Level 7 (Highest) MVTX2804 Bit [6]: Fixed Discard priority (Default 0) Used When Bit [7] = 1 * 0 - Discard Priority Level 0 (Lowest) * 1 Discard Priority Level 1 (Highest) Bit [7]: Enable Fix Priority (Default 0) * 0 Disable fix priority. All frames are analyzed. Transmit Priority and Drop Priority are based on VLAN Tag or TOS. * 1 Transmit Priority and Discard Priority are based on values programmed in bit [6:3] 11.5 Port VLAN Map PVMAP00_0,1,3 I2C Address h14,15,17; CPU Address:h102,103,105) PVMAP01_0,1,3 I2C Address h18,19,1B; CPU Address:h106,107,109) PVMAP02_0,1,3 I2C Address h1C,1D,1F; CPU Address:h10A, 10B,10D) PVMAP03_0,1,3 I2C Address h20,21,23; CPU Address:h10E, 10F,111) PVMAP04_0,1,3 I2C Address h24,25,27; CPU Address:h112, 113,115) PVMAP05_0,1,3 I2C Address h28,29,2B; CPU Address:h116, 117,119) PVMAP06_0,1,3 I2C Address h2C,2D,2F; CPU Address:h11A, 11B,11D) PVMAP07_0,1,3 I2C Address h30,31,33; CPU Address:h11E, 11F,121) 11.5.1 * * PVMODE I2C Address: h038, CPU Address:h126 Accessed by CPU, serial interface (R/W) 7 RO Bit [0]: * 6 MP 5 BPDU 4 DM 3 Reserved 1 Vmod 0 VLAN Mode (vlan_enable) (Default = 0) * 1: Tag Based VLAN Mode * 0: Port Based VLAN Mode Bit [4]: * Disable MAC address 0 * 0: MAC address 0 is not leaned. * 1: MAC address 0 is leaned. Zarlink Semiconductor Inc. 57 MVTX2804 Bit [5]: * Force BPDU as multicast frame (Default 0) * 1: Enable. * 0: Disable. BPDU packet is forwarded to CPU. Data Sheet Bit [6]: * MAC/PORT * 0: Single MAC address per system * 1: Single MAC address per port Bit [7]: * Routing option (force frame as switched frame) * 1: Routing Frame to CPU is independent of ingress port spanning tree state * 0: Routing Frame to CPU is dependent of ingress port spanning tree state 11.6 11.6.1 11.6.1.1 * * * * Group 2 Address Port Trunking Group TRUNK0 - TRUNK GROUP 0 MEMBER (MANAGED MODE ONLY) CPU Address:h200 Accessed by CPU, serial interface (R/W) Bit [7:0] Port7-0 bit map of trunk 0. (Default 00) TRUNK0 provides a bitmap for trunk0 membership. Example: To trunk ports 0 and 2 in trunk group 0, bits 0 and 2 of TRUNK0 must be set to 1. All others must be cleared to "0" to indicate that they are not members of the trunk 0. 11.6.1.2 * * * TRUNK1 - TRUNK GROUP 1 MEMBER (MANAGED MODE ONLY) CPU Address:h201 Accessed by CPU, serial interface (R/W) Bit [7:0] Port7-0 bit map of trunk 1. (Default 00) 11.6.1.3 * * * TRUNK2- TRUNK GROUP 2 MEMBER (MANAGED MODE ONLY) CPU Address:h202 Accessed by CPU, serial interface (R/W) Bit [7:0] Port7-0 bit map of trunk 2. (Default 00) 11.6.1.4 * * * TRUNK3- TRUNK GROUP 3 MEMBER (MANAGED MODE ONLY) CPU Address:h203 Accessed by CPU, serial interface (R/W) Bit [7:0] Port7-0 bit map of trunk 3. (Default 00) 11.6.1.5 TRUNK_HASH_MODE - TRUNK HASH MODE * CPU Address:h206 * Accessed by CPU, serial interface (R/W) Hash Select. The hash selected is valid for Trunk 0, 1, 2 and 3. 7 2 1 Hash sel 0 58 Zarlink Semiconductor Inc. Data Sheet Bit [1:0] * (Default 2'b00) * * * * 00 - Use Source and Destination Mac address for hashing. 01 - Use Source Mac Address for hashing. 10 - Use Destination Mac Address for hashing. 11 - Not Used. MVTX2804 11.6.1.6 TRUNK0_MODE - TRUNK GROUP 0 MODE (UNMANAGED MODE) * I2C Address: h039, CPU Address:h207 * Accessed by serial interface and I2C (R/W) Port Selection in unmanaged mode. Trunk group 0 and trunk group 1 are enable accordingly to bits [1:0] when input pin P_d[9] = 0 (external pull down). 7 2 1 Port sel Bit [1:0] * Port member selection for Trunk 0 and 1 in unmanaged mode (Default 2'b00) * 00 - Only trunk group 0 is enable. Port 0 and 1 are used for trunk group0 * 01 - Only trunk group 0 is enable. Port 0,1 and 2 are used for trunk group0 * 10 - Only trunk group 0 is enable. Port 0,1,2 and 3 are used for trunk group0 * 11 - Trunk group 0 and 1 are enable. Port 0, 1 are used for trunk group0, and port 2 and 3 are used for trunk group1 0 TRUNK HASH * * * * Trunk Trunk Trunk Trunk group group group group 0 1 2 3 achieve achieve achieve achieve load load load load balance balance balance balance by by by by TRUNK0_HASH0 TRUNK1_HASH0 TRUNK2_HASH0 TRUNK3_HASH0 to 5. to 5. to 5. to 5. (only (only (only (only in in in in managed managed managed managed mode) mode) mode) mode) 11.6.1.7 TRUNK0_HASH0 - TRUNK GROUP 0 HASH RESULT 0,1,2 DESTINATION PORT NUMBER * * CPU Address:h208 Accessed by CPU, serial interface (R/W) Bit [2:0]: Bit [5:3] Bit [7:6] * * * Hash result 0 destination port number[2:0] (Default 000) Hash result 1 destination port number[2:0] (Default 001) Hash result 2 destination port number[1:0] (Default 00) 11.6.1.8 TRUNK0_HASH1 - TRUNK GROUP 0 HASH RESULT 2,3,4,5 DESTINATION PORT NUMBER * * CPU Address:h209 Accessed by CPU, serial interface (R/W) Bit [0]: Bit [3:1]: * * Hash result 2 destination port number[2] (Default 0) Hash result 3 destination port number[2:0] (Default 001) Zarlink Semiconductor Inc. 59 MVTX2804 Bit [6:4]: Bit [7]: * * Hash result 4 destination port number[2:0] (Default 000) Hash result 5 destination port number[0] (Default 1) Data Sheet 11.6.1.9 TRUNK0_HASH2 - TRUNK GROUP 0 HASH RESULT 5,6,7 DESTINATION PORT NUMBER * * CPU Address:h20A Accessed by CPU, serial interface (R/W) Bit [1:0]: Bit [4:2] Bit [7:5] * * * Hash result 5 destination port number[2:1] (Default 00) Hash result 6 destination port number[2:0] (Default 000) Hash result 7 destination port number[2:0] (Default 001) 11.6.1.10 TRUNK0_HASH3 - TRUNK GROUP 0 HASH RESULT 8,9,10 DESTINATION PORT NUMBER * * CPU Address:h20B Accessed by CPU, serial interface (R/W) Bit [2:0]: Bit [5:3] Bit [7:6] * * * Hash result 8 destination port number[2:0] (Default 000) Hash result 9 destination port number[2:0] (Default 001) Hash result 10 destination port number[1:0] (Default 00) 11.6.1.11 TRUNK0_HASH4 - TRUNK GROUP 0 HASH RESULT 10,11,12,13 DESTINATION PORT NUMBER * * CPU Address:h20C Accessed by CPU, serial interface (R/W) Bit [0]: Bit [3:1] Bit[6:4] Bit [7] * * * * Hash result 10 destination port number[2] (Default 0) Hash result 11 destination port number[2:0] (Default 001) Hash result 12 destination port number[2:0] (Default (000) Hash result 13 destination port number[2:0] (Default (1) 11.6.1.12 TRUNK0_HASH5 - TRUNK GROUP 0 HASH RESULT 13,14,15 DESTINATION PORT NUMBER * * CPU Address:h20D Accessed by CPU, serial interface (R/W) Bit [1:0]: Bit [4:2] Bit [7:5] Hash result 13 destination port number[2:1] (Default 00) Hash result 14 destination port number[2:0] (Default 000) Hash result 15 destination port number[2:0] (Default 001) 60 Zarlink Semiconductor Inc. Data Sheet 11.6.1.13 TRUNK1_MODE - TRUNK GROUP 1 MODE (UNMANAGED MODE) * * * MVTX2804 I2C Address h03A; CPU Address:20E Accessed by CPU, serial interface and I2C (R/W) Port Selection in unmanaged mode. Trunk group 2 and trunk group 3 are enable accordingly to bits [1:0] when input pin P_d[10] = 0. 7 2 1 Port Select Bit [1:0]: * Port member selection for Trunk 2 and 3 in unmanaged mode * * * * 00 - Only trunk group 2 is enable. Port 4 and 5 are used for trunk group 2 01 - Only trunk group 2 is enable. Port 4, 5 and 6 are used for trunk group 2 10 - Only trunk group 2 is enable. Port 4, 5, 6 and 7 are used for trunk group 2 11 - Trunk group 2 and trunk group 3 are enable. Port 4 and 5 are used for trunk group 2, and port 6 and 7 are used for trunk group 3 0 11.6.1.14 TRUNK1_HASH0 - TRUNK GROUP 1 HASH RESULT 0, 1, 2 DESTINATION PORT NUMBER * * CPU Address:h20F Accessed by CPU, serial interface (R/W) Bit [2:0]: Bit [7:6] Bit [5:3] * * * Hash result 0 destination port number[2:0] (Default 000) Hash result 2 destination port number[1:0] (Default 00) Hash result 1 destination port number[2:0] (Default 001) 11.6.1.15 TRUNK1_HASH1 - TRUNK GROUP 1 HASH RESULT 2, 3, 4, 5 DESTINATION PORT NUMBER * * CPU Address:h210 Accessed by CPU, serial interface (R/W) Bit [0]: Bit [3:1 Bit [6:4] Bit [7] * * * * Hash result 2 destination port number[2] (Default 0) Hash result 3 destination port number[2:0] (Default 001) Hash result 4 destination port number[2:0] (Default 000) Hash result 5 destination port number[0] (Default 1) 11.6.1.16 TRUNK1_HASH2 - TRUNK GROUP 1 HASH RESULT 5, 6, 7 DESTINATION PORT NUMBER * * CPU Address:h211 Accessed by CPU, serial interface (R/W) Bit [1:0]: Bit [4:2] Bit [7:5] * * * Hash result 5 destination port number[2:1] (Default 00) Hash result 6 destination port number[2:0] (Default 000) Hash result 7 destination port number[2:0] (Default 001) Zarlink Semiconductor Inc. 61 MVTX2804 Data Sheet 11.6.1.17 TRUNK1_HASH3 - TRUNK GROUP 1 HASH RESULT 8, 9, 10 DESTINATION PORT NUMBER * * CPU Address:h212 Accessed by CPU, serial interface (R/W) Bit [2:0] Bit [5:3] Bit [7:6] * * * Hash result 8 destination port number[2:0] (Default 000) Hash result 9 destination port number[2:0] (Default 001) Hash result 10 destination port number[1:0] (Default 00) 11.6.1.18 TRUNK1_HASH4- TRUNK GROUP 1 HASH RESULT 11, 12, 13 DESTINATION PORT NUMBER * * CPU Address:h213 Accessed by CPU, serial interface (R/W) Bit [0]: Bit [3:1] Bit [6:4] Bit [7] * * * * Hash result 10 destination port number[2] (Default 0) Hash result 11 destination port number[2:0] (Default 001) Hash result 12 destination port number[2:0] (Default (000) Hash result 13 destination port number[0] (Default (1) 11.6.1.19 TRUNK1_HASH5 - TRUNK GROUP 1 HASH RESULT 13, 14, 15 DESTINATION PORT NUMBER * * CPU Address:h214 Accessed by CPU, serial interface (R/W) Bit [1:0]: Bit [4:2] Bit [7:5] * * * Hash result 13 destination port number[2:1] (Default 00) Hash result 14 destination port number[2:0] (Default 000) Hash result 15 destination port number[2:0] (Default 001) 11.6.1.20 TRUNK2_HASH0 - TRUNK GROUP 2 HASH RESULT 0, 1, 2 DESTINATION PORT NUMBER * * CPU Address:h215 Accessed by CPU, serial interface (R/W) Bit [2:0]: Bit [5:3] Bit [7:6] * * * Hash result 0 destination port number[2:0] (Default 100) Hash result 1 destination port number[2:0] (Default 101) Hash result 2 destination port number[1:0] (Default 00) 11.6.1.21 TRUNK2_HASH1 - TRUNK GROUP 2 HASH RESULT 2, 3, 4, 5 DESTINATION PORT NUMBER * * CPU Address:h216 Accessed by CPU, serial interface (R/W) Bit [0]: Bit [3:1] * * Hash result 2 destination port number[2] (Default 1) Hash result 3 destination port number[2:0] (Default 101) 62 Zarlink Semiconductor Inc. Data Sheet Bit [6:4] Bit [7] * * Hash result 4 destination port number[2:0] (Default 100) Hash result 5 destination port number[0] (Default 1) MVTX2804 11.6.1.22 TRUNK2_HASH2 - TRUNK GROUP 2 HASH RESULT 5, 6, 7 DESTINATION PORT NUMBER * * CPU Address:h217 Accessed by CPU, serial interface (R/W) Bit [1:0]: Bit [4:2] Bit [7:5] * * * Hash result 5 destination port number[2:1] (Default 10) Hash result 6 destination port number[2:0] (Default 100) Hash result 7 destination port number[2:0] (Default 101) 11.6.1.23 TRUNK2_HASH3 - TRUNK GROUP 2 HASH RESULT 8, 9, 10 DESTINATION PORT NUMBER * * CPU Address:h218 Accessed by CPU, serial interface (R/W) Bit [2:0]: Bit [5:3] Bit [7:6] * * * Hash result 8 destination port number[2:0] (Default 000) Hash result 9 destination port number[2:0] (Default 001) Hash result 10 destination port number[1:0] (Default 00) 11.6.1.24 TRUNK0_HASH3 - TRUNK GROUP 0 HASH RESULT 8,9,10 DESTINATION PORT NUMBER * * CPU Address:h20B Accessed by CPU, serial interface (R/W) Bit [2:0]: Bit [5:3] Bit [7:6] * * * Hash result 8 destination port number[2:0] (Default 000) Hash result 9 destination port number[2:0] (Default 001) Hash result 10 destination port number[1:0] (Default 00) 11.6.1.25 TRUNK0_HASH4 - TRUNK GROUP 0 HASH RESULT 10,11,12,13 DESTINATION PORT NUMBER * * CPU Address:h20C Accessed by CPU, serial interface (R/W) Bit [0]: Bit [3:1] Bit[6:4] Bit [7] * * * * Hash result 10 destination port number[2] (Default 0) Hash result 11 destination port number[2:0] (Default 001) Hash result 12 destination port number[2:0] (Default (000) Hash result 13 destination port number[2:0] (Default (1) Zarlink Semiconductor Inc. 63 MVTX2804 Data Sheet 11.6.1.26 TRUNK0_HASH5 - TRUNK GROUP 0 HASH RESULT 13,14,15 DESTINATION PORT NUMBER * * CPU Address:h20D Accessed by CPU, serial interface (R/W) Bit [1:0]: Bit [4:2] Bit [7:5] Hash result 13 destination port number[2:1] (Default 00) Hash result 14 destination port number[2:0] (Default 000) Hash result 15 destination port number[2:0] (Default 001) 11.6.1.27 TRUNK1_MODE - TRUNK GROUP 1 MODE (UNMANAGED MODE) * * * I2C Address h03A; CPU Address:20E Accessed by CPU, serial interface and I2C (R/W) Port Selection in unmanaged mode. Trunk group 2 and trunk group 3 are enable accordingly to bits [1:0] when input pin P_d[10] = 0. 7 2 1 Port Select Bit [1:0]: * Port member selection for Trunk 2 and 3 in unmanaged mode * * * * 00 - Only trunk group 2 is enable. Port 4 and 5 are used for trunk group 2 01 - Only trunk group 2 is enable. Port 4, 5 and 6 are used for trunk group 2 10 - Only trunk group 2 is enable. Port 4, 5, 6 and 7 are used for trunk group 2 11 - Trunk group 2 and trunk group 3 are enable. Port 4 and 5 are used for trunk group 2, and port 6 and 7 are used for trunk group 3 0 11.6.1.28 TRUNK1_HASH0 - TRUNK GROUP 1 HASH RESULT 0, 1, 2 DESTINATION PORT NUMBER * * CPU Address:h20F Accessed by CPU, serial interface (R/W) Bit [2:0]: Bit [7:6] Bit [5:3] * * * Hash result 0 destination port number[2:0] (Default 000) Hash result 2 destination port number[1:0] (Default 00) Hash result 1 destination port number[2:0] (Default 001) 11.6.1.29 TRUNK1_HASH1 - TRUNK GROUP 1 HASH RESULT 2, 3, 4, 5 DESTINATION PORT NUMBER * * CPU Address:h210 Accessed by CPU, serial interface (R/W) Bit [0]: Bit [3:1 Bit [6:4] Bit [7] * * * * Hash result 2 destination port number[2] (Default 0) Hash result 3 destination port number[2:0] (Default 001) Hash result 4 destination port number[2:0] (Default 000) Hash result 5 destination port number[0] (Default 1) 64 Zarlink Semiconductor Inc. Data Sheet MVTX2804 11.6.1.30 TRUNK1_HASH2 - TRUNK GROUP 1 HASH RESULT 5, 6, 7 DESTINATION PORT NUMBER * * CPU Address:h211 Accessed by CPU, serial interface (R/W) Bit [1:0]: Bit [4:2] Bit [7:5] * * * Hash result 5 destination port number[2:1] (Default 00) Hash result 6 destination port number[2:0] (Default 000) Hash result 7 destination port number[2:0] (Default 001) 11.6.1.31 TRUNK1_HASH3 - TRUNK GROUP 1 HASH RESULT 8, 9, 10 DESTINATION PORT NUMBER * * CPU Address:h212 Accessed by CPU, serial interface (R/W) Bit [2:0] Bit [5:3] Bit [7:6] * * * Hash result 8 destination port number[2:0] (Default 000) Hash result 9 destination port number[2:0] (Default 001) Hash result 10 destination port number[1:0] (Default 00) 11.6.1.32 TRUNK1_HASH4- TRUNK GROUP 1 HASH RESULT 11, 12, 13 DESTINATION PORT NUMBER * * CPU Address:h213 Accessed by CPU, serial interface (R/W) Bit [0]: Bit [3:1] Bit [6:4] Bit [7] * * * * Hash result 10 destination port number[2] (Default 0) Hash result 11 destination port number[2:0] (Default 001) Hash result 12 destination port number[2:0] (Default (000) Hash result 13 destination port number[0] (Default (1) 11.6.1.33 TRUNK1_HASH5 - TRUNK GROUP 1 HASH RESULT 13, 14, 15 DESTINATION PORT NUMBER * * CPU Address:h214 Accessed by CPU, serial interface (R/W) Bit [1:0]: Bit [4:2] Bit [7:5] * * * Hash result 13 destination port number[2:1] (Default 00) Hash result 14 destination port number[2:0] (Default 000) Hash result 15 destination port number[2:0] (Default 001) 11.6.1.34 TRUNK2_HASH0 - TRUNK GROUP 2 HASH RESULT 0, 1, 2 DESTINATION PORT NUMBER * * CPU Address:h215 Accessed by CPU, serial interface (R/W) Bit [2:0]: Bit [5:3] * * Hash result 0 destination port number[2:0] (Default 100) Hash result 1 destination port number[2:0] (Default 101) Zarlink Semiconductor Inc. 65 MVTX2804 Bit [7:6] * Hash result 2 destination port number[1:0] (Default 00) Data Sheet 11.6.1.35 TRUNK2_HASH1 - TRUNK GROUP 2 HASH RESULT 2, 3, 4, 5 DESTINATION PORT NUMBER * * CPU Address:h216 Accessed by CPU, serial interface (R/W) Bit [0]: Bit [3:1] Bit [6:4] Bit [7] * * * * Hash result 2 destination port number[2] (Default 1) Hash result 3 destination port number[2:0] (Default 101) Hash result 4 destination port number[2:0] (Default 100) Hash result 5 destination port number[0] (Default 1) 11.6.1.36 TRUNK2_HASH2 - TRUNK GROUP 2 HASH RESULT 5, 6, 7 DESTINATION PORT NUMBER * * CPU Address:h217 Accessed by CPU, serial interface (R/W) Bit [1:0]: Bit [4:2] Bit [7:5] * * * Hash result 5 destination port number[2:1] (Default 10) Hash result 6 destination port number[2:0] (Default 100) Hash result 7 destination port number[2:0] (Default 101) 11.6.1.37 TRUNK2_HASH3 - TRUNK GROUP 2 HASH RESULT 8, 9, 10 DESTINATION PORT NUMBER * * CPU Address:h218 Accessed by CPU, serial interface (R/W) Bit [2:0]: Bit [5:3] Bit [7:6] * * * Hash result 8 destination port number[2:0] (Default 000) Hash result 9 destination port number[2:0] (Default 001) Hash result 10 destination port number[1:0] (Default 00) 11.6.1.38 TRUNK2_HASH4 - TRUNK GROUP 2 HASH RESULT 10, 11, 12, 13 DESTINATION PORT NUMBER * * CPU Address:h219 Accessed by CPU, serial interface (R/W) Bit [0]: Bit [3:1] Bit [6:4] Bit [7] * * * * Hash result 10 destination port number[2] (Default 1) Hash result 11 destination port number[2:0] (Default 101) Hash result 12 destination port number[2:0] (Default 1000) Hash result 13 destination port number[2:0] (Default (1) 66 Zarlink Semiconductor Inc. Data Sheet MVTX2804 11.6.1.39 TRUNK2_HASH5 - TRUNK GROUP 2 HASH RESULT 13, 14, 15 DESTINATION PORT NUMBER * * CPU Address:h21A Accessed by CPU, serial interface (R/W) Bit [1:0]: Bit [4:2] Bit [7:5] * * * Hash result 13 destination port number[2:1] (Default 10) Hash result 14 destination port number[2:0] (Default 100) Hash result 15 destination port number[2:0] (Default 101) 11.6.1.40 TRUNK3_HASH0 - TRUNK GROUP 3 HASH RESULT 0, 1, 2 DESTINATION PORT NUMBER * * CPU Address:h21B Accessed by CPU, serial interface (R/W) Bit [2:0]: Bit [5:3] Bit [7:6] * * * Hash result 0 destination port number[2:0] (Default 100) Hash result 1 destination port number[2:0] (Default 101) Hash result 2 destination port number[1:0] (Default 00) 11.6.1.41 TRUNK3_HASH1 - TRUNK GROUP 3 HASH RESULT 2, 3, 4, 5 DESTINATION PORT NUMBER * * CPU Address:h21C Accessed by CPU, serial interface (R/W) Bit [0]: Bit [3:1] Bit [6:4] Bit [7] * * * * Hash result 2 destination port number[2] (Default 1) Hash result 3 destination port number[2:0] (Default 101) Hash result 4 destination port number[2:0] (Default 100) Hash result 5 destination port number[0] (Default 1) 11.6.1.42 TRUNK3_HASH2 - TRUNK GROUP 3 HASH RESULT 5, 6, 7 DESTINATION PORT NUMBER * * CPU Address:h21D Accessed by CPU, serial interface (R/W) Bit [1:0]: Bit [4:2] Bit [7:5] * * * Hash result 5 destination port number[2:1] (Default 10) Hash result 6 destination port number[2:0] (Default 100) Hash result 7 destination port number[2:0] (Default 101) 11.6.1.43 TRUNK3_HASH3 - TRUNK GROUP 3 HASH RESULT 8, 9, 10 DESTINATION PORT NUMBER * * CPU Address:h21E Accessed by CPU, serial interface (R/W) Bit [2:0]: Bit [5:3] Bit [7:6] * * * Hash result 8 destination port number[2:0] (Default 100) Hash result 9 destination port number[2:0] (Default 101) Hash result 10 destination port number[1:0] (Default 00) Zarlink Semiconductor Inc. 67 MVTX2804 Data Sheet 11.6.1.44 TRUNK3_HASH4 - TRUNK GROUP 3 HASH RESULT 10, 11, 12, 13 DESTINATION PORT NUMBER * * CPU Address:h21F Accessed by CPU, serial interface (R/W) Bit [0]: Bit [3:1] Bit [6:4] Bit [7] * * * * Hash result 10 destination port number[2] (Default 1) Hash result 11 destination port number[2:0] (Default 101) Hash result 12 destination port number[2:0] (Default (100) Hash result 13 destination port number[2:0] (Default (1) 11.6.1.45 TRUNK3_HASH5 - TRUNK GROUP 3 HASH RESULT 13, 14, 15 DESTINATION PORT NUMBER * * CPU Address:h220 Accessed by CPU, serial interface (R/W) Bit [1:0]: Bit [4:2] Bit [7:5] * * * Hash result 13 destination port number[2:1] (Default 10) Hash result 14 destination port number[2:0] (Default 100) Hash result 15 destination port number[2:0] (Default 101) 11.6.2 Multicast Hash Registers Multicast Hash registers are used to distribute multicast traffic. 16 + 2 registers are used to form a 16-entry array; each entry has 9 bits, with each bit representing one port. Any port not belonging to a trunk group should be programmed with 1. Ports belonging to the same trunk group should only have a single port set to "1" per entry. The port set to "1" is picked to transmit the multicast frame when the hash value is met. Bit Hash Result = 0 Hash Result = 1 Hash Result = 2 ... Hash Result = 13 Hash Result = 14 Hash Result = 15 Port 0 Port 3 Port 2 Port 1 8 7 6 5 4 3 2 1 0 CPU Port Port 7 Port 6 Port 5 Port 4 11.6.2.1 * * * MULTICAST_HASH00 - MULTICAST HASH RESULT0 MASK BYTE [7:0] CPU Address:h221 Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) 68 Zarlink Semiconductor Inc. Data Sheet 11.6.2.2 * * * MVTX2804 MULTICAST_HASH01 - MULTICAST HASH RESULT1 MASK BYTE [7:0] CPU Address:h222 Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) 11.6.2.3 * * * MULTICAST_HASH02 - MULTICAST HASH RESULT2 MASK BYTE [7:0] CPU Address:h223 Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) 11.6.2.4 * * * MULTICAST_HASH03 - MULTICAST HASH RESULT3 MASK BYTE [7:0] CPU Address:h224 Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) 11.6.2.5 * * * MULTICAST_HASH04 - MULTICAST HASH RESULT4 MASK BYTE [7:0] CPU Address:h225 Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) 11.6.2.6 * * * MULTICAST_HASH05 - MULTICAST HASH RESULT5 MASK BYTE [7:0] CPU Address:h226 Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) 11.6.2.7 * * * MULTICAST_HASH06 - MULTICAST HASH RESULT6 MASK BYTE [7:0] CPU Address:h227 Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) 11.6.2.8 * * * MULTICAST_HASH07 - MULTICAST HASH RESULT7 MASK BYTE [7:0] CPU Address:h228 Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) 11.6.2.9 * * * MULTICAST_HASH08 - MULTICAST HASH RESULT8 MASK BYTE [7:0] CPU Address:h229 Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) 11.6.2.10 MULTICAST_HASH09 - MULTICAST HASH RESULT9 MASK BYTE [7:0] * * * CPU Address:h22A Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) Zarlink Semiconductor Inc. 69 MVTX2804 11.6.2.11 MULTICAST_HASH10 - MULTICAST HASH RESULT10 MASK BYTE [7:0] * * * CPU Address:h22B Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) Data Sheet 11.6.2.12 MULTICAST_HASH11 - MULTICAST HASH RESULT11 MASK BYTE [7:0] * * * CPU Address:h22C Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) 11.6.2.13 MULTICAST_HASH12 - MULTICAST HASH RESULT12 MASK BYTE [7:0] * * * CPU Address:h22D Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) 11.6.2.14 MULTICAST_HASH13 - MULTICAST HASH RESULT13 MASK BYTE [7:0] * * * CPU Address:h22E Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) 11.6.2.15 MULTICAST_HASH14 - MULTICAST HASH RESULT14 MASK BYTE [7:0] * * * CPU Address:h22F Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) 11.6.2.16 MULTICAST_HASH15 - MULTICAST HASH RESULT15 MASK BYTE [7:0] * * * CPU Address:h230 Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) 11.6.2.17 MULTICAST_HASHML - MULTICAST HASH BIT[8] FOR RESULT7-0 * * * CPU Address:h231 Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) 11.6.2.18 MULTICAST_HASHML - MULTICAST HASH BIT[8] FOR RESULT 15-8 * * * CPU Address:h232 Accessed by CPU, serial interface (R/W) Bit [7:0] (Default FF) 70 Zarlink Semiconductor Inc. Data Sheet 11.7 11.7.1 Group 3 Address CPU Port Configuration Group MVTX2804 MAC5 to MAC0 registers form the CPU address. When a packet with destination address equal to MAC5[5:0] arrives, it is forwarded to the CPU. (MC bit) MAC5 MAC4 MAC3 MAC2 MAC1 MAC0 11.7.1.1 * * * MAC0 - CPU MAC ADDRESS BYTE 0 CPU Address:h300 Accessed by CPU Bit [7:0] Byte 0 of the CPU MAC address. (Default 8'00) 11.7.1.2 * * * MAC1 - CPU MAC ADDRESS BYTE 1 CPU Address:h301 Accessed by CPU Bit [7:0] Byte 1 of the CPU MAC address. (Default 8'00) 11.7.1.3 * * * MAC2 - CPU MAC ADDRESS BYTE 2 CPU Address:h302 Accessed by CPU Bit [7:0] Byte 2 of the CPU MAC address. (Default 8'00) 11.7.1.4 * * * MAC3 - CPU MAC ADDRESS BYTE 3 CPU Address:h303 Accessed by CPU Bit [7:0] Byte 3 of the CPU MAC address. (Default 8'00) 11.7.1.5 * * * MAC4 - CPU MAC ADDRESS BYTE 4 CPU Address:h304 Accessed by CPU Bit [7:0] Byte 4 of the CPU MAC address. (Default 8'00) 11.7.1.6 * * * MAC5 - CPU MAC ADDRESS BYTE 5 CPU Address:h305 Accessed by CPU Bit [7:0] Byte 5 of the CPU MAC address. (Default 8'00). These registers form the CPU MAC address Zarlink Semiconductor Inc. 71 MVTX2804 11.7.1.7 INT_MASK0 - INTERRUPT MASK 0 Data Sheet * CPU Address:h306 * Accessed by CPU, serial interface (R/W) * Mask off the interrupt source The CPU can dynamically mask the interruption when it is busy and doesn't want to be interrupted Bit [0]: Bit [1]: Bit [2]: Bit [7:3]: * * * * CPU frame interrupt. CPU frame buffer has data for CPU to read (Default 1'b1) Control Command Frame 1 interrupt. Control Command Frame buffer1 has data for CPU to read (Default 1'b1) Control Command Frame 2 interrupt. Control Command Frame buffer2 has data for CPU to read (Default 1'b1) Reserved * 1 - Mask the interrupt * 0 - Unmask the interrupt (Enable interrupt) 11.7.1.8 * * * INT_MASK1 - INTERRUPT MASK 1 CPU Address:h307 Accessed by CPU, serial interface (R/W) Mark off the interrupt source Bit [0]: Bit [1]: Bit [2]: Bit [3]: Bit [4]: Bit [5]: Bit [6]: Bit [7]: * * * * * * * * From Gigabit port 0 interrupt (Default 1'b1) From Gigabit port 1 interrupt (Default 1'b1) From Gigabit port 2 interrupt (Default 1'b1) From Gigabit port 3 interrupt (Default 1'b1) From Gigabit port 4 interrupt (Default 1'b1) From Gigabit port 5 interrupt (Default 1'b1) From Gigabit port 6 interrupt (Default 1'b1) From Gigabit port 7 interrupt (Default 1'b1) * 1 - Mask the interrupt * 0 - Unmask the interrupt (Enable interrupt) 11.7.1.9 * * * INT_STATUS0 - MASKED INTERRUPT STATUS REGISTER0 CPU Address:h30A Access by CPU, serial interface (RO) Indicate the source of the masked interrupt. Bit [0]: Bit [1]: Bit [2]: Bit [3]: Bit [7:4]: * * * * * CPU frame interrupt. Control Command Frame 1 interrupt. Control Command Frame 2 interrupt. From any of the Gigabit port interrupt. Reserved. 72 Zarlink Semiconductor Inc. Data Sheet 11.7.1.10 INT_STATUS1 - MASKED INTERRUPT STATUS REGISTER1 * * * (CPU Address:h30B) Access by CPU, serial interface (RO) Indicate the source of the masked interrupt. Bit [0]: Bit [1]: Bit [2]: Bit [3]: Bit [4]: Bit [5]: Bit [6]: Bit [7]: * * * * * * * * From Gigabit port 0 interrupt From Gigabit port 1 interrupt From Gigabit port 2 interrupt From Gigabit port 3 interrupt From Gigabit port 4 interrupt From Gigabit port 5 interrupt From Gigabit port 6 interrupt From Gigabit port 7 interrupt MVTX2804 11.7.1.11 INTP_MASK0 - INTERRUPT MASK FOR MAC PORT 0,1 * * CPU Address:h30C Accessed by CPU, serial interface (R/W) The CPU can dynamically mask the interruption when it is busy and doesn't want to be interrupted 7 6 5 P1 1 - Mask the Interrupt 0 - Unmask the Interrupt (Enable interrupt) 4 3 2 1 P0 0 Bit[0]: Port 0 statistic counter Wrap around interrupt mask. An interrupt is generated when a statistic counter gets to its maximum value and wraps around. Refer to hardware statistic counter for interrupt sources. (Default 1'b1) Bit [1]: Port 0 Link change mask. (Default 1'b1) Bit [4]: Port 1 statistic counter Wrap around interrupt mask. (Default 1'b1) Bit [5]: Port 1 Link change mask. (Default 1'b1) 11.7.1.12 INTP_MASK1 - INTERRUPT MASK FOR MAC PORT 2,3 * * CPU Address:h30D Accessed by CPU, serial interface (R/W) 7 6 5 P3 Bit [0]: Bit [1]: * * Port 2 WAS mask (Default 1'b1) Port 2 link change mask (Default 1'b1) 4 3 2 1 P2 0 Zarlink Semiconductor Inc. 73 MVTX2804 Bit [4]: Bit [5]: * * Port 3 WAS mask (Default 1'b1) Port 3 link change mask (Default 1'b1) Data Sheet 11.7.1.13 INTP_MASK4 - INTERRUPT MASK FOR MAC PORT 4,5 * * CPU Address:h30E Accessed by CPU, serial interface (R/W) 7 6 5 P4 Bit [0]: Bit [1]: Bit [4]: Bit [5]: * * * * Port 4 WAS mask (Default 1'b1) Port 4 link change mask (Default 1'b1) Port 5 WAS mask (Default 1'b1) Port 5 link change mask (Default 1'b1) 4 3 2 1 P5 0 11.7.1.14 INTP_MASK5 - INTERRUPT MASK FOR MAC PORT 6,7 * * CPU Address:h30F Accessed by CPU, serial interface (R/W) 7 6 5 P6 Bit [0]: Bit [1]* Bit [4]* Bit [5]: * * * * Port 6 WAS mask (Default 1'b1) Port 6 link change mask (Default 1'b1) Port 7 WAS mask (Default 1'b1) Port 7 link change mask (Default 1'b1) 4 3 2 1 P7 0 11.7.2 * * * RQS - Receive Queue Select CPU Address:h310 Accessed by CPU, serial interface (RW) This register selects which receive queue is enable to send data to the CPU. 7 FQ3 6 FQ2 5 FQ1 4 FQ0 3 SQ3 2 SQ2 1 SQ1 0 SQ0 Bit[0]: Select Queue 0. If set to one, this queue may be scheduled to CPU port. If set to zero, this queue will be blocked. If multiple queues are selected, a strict priority will be applied. Q3> Q2> Q1> Q0. Same applies to bits [3:1]. See QoS application note for more information. Bit[1]: Select Queue 1 Bit[2]: Select Queue 2 Bit[3]: Select Queue 3 Note: Strip priority applies between different selected queues (Q3>Q2>Q1>Q0) Bit[4]: Enable flush Queue 0 Bit[5]: Enable flush Queue 1 74 Zarlink Semiconductor Inc. Data Sheet Bit[6]: Enable flush Queue 2 Bit[7]: Enable flush Queue 3 MVTX2804 When flush (drop frames) is enable, it starts when queue is too long or entry is too old. A queue is too long when it reaches WRED thresholds. Queue 0 is not subject to early drop. Packets in queue 0 are dropped only when the queue is too old. An entry is too old when it is older than the time programmed in the register TX_AGE [5:0]. CPU can dynamically program this register reading register RQSS [7:4]. 11.7.3 * * RQSS - Receive Queue Status CPU Address:h311 Accessed by CPU, serial interface (RO) 7 LQ3 6 LQ2 5 LQ1 4 LQ0 3 NeQ3 2 NeQ2 1 NeQ1 0 NeQ0 CPU queue status: Bit[3:0]: Queue 3 to 0 not empty Bit[4]: Head of line entry for Queue 3 to 0 is valid for too long. CPU queue 0 has no WRED threshold Bit[7:5]: Head of line entry for Queue 3 to 0 is valid for too long or Queue length is longer than WRED threshold 11.7.4 * * I 2C TX_AGE - Tx Queue Aging timer Address: h03B;CPU Address:h312 Accessed by CPU, serial interface (RO) 7 6 5 4 Tx Queue Agent Bit[4:0]: Bit[5] Bit[7:6]: * * * Unit of 100ms (Default 8)Disable transmission queue aging if value is zero. Must be set to '0' Reserved 0 11.8 11.8.1 11.8.1.1 * * * * 2 Group 4 Address Search Engine Group AGETIME_LOW - MAC ADDRESS AGING TIME LOW I C Address h03C; CPU Address:h400 Accessed by CPU, serial interface and I2C (R/W) Bit [7:0] Low byte of the MAC address aging timer. (Default 2c) The 2800 removes the MAC address from the data base and sends a Delete MAC Address Control Command to the CPU. Mac address aging is enable/disable by boot strap T_d[9]. 11.8.1.2 * * AGETIME_HIGH -MAC ADDRESS AGING TIME HIGH I2C Address h03D; CPU Address:h401 Accessed by CPU, serial interface and I2C (R/W) Zarlink Semiconductor Inc. 75 MVTX2804 * Bit [7:0]: High byte of the MAC address aging timer. (Default 00) * Aging time is based on the following equation: {AGETIME_HIGH,AGETIME_LOW} X (# of MAC entries X100sec) Data Sheet Note: the number of entries= 66K when T_d[5] is pull down (SRAM memory size = 512K) and 34K when T_d[5] is pull up (SRAM memory size = 256K). 11.8.1.3 * * * V_AGETIME - VLAN TO PORT AGING TIME CPU Address:h402 Accessed by CPU (R/W) Bit [7:0] - 2msec/unit. (Default FF) 11.8.1.4 * * SE_OPMODE - SEARCH ENGINE OPERATION MODE CPU Address:h403 Accessed by CPU (R/W) 7 SL Bit [0]: * 6 DMS 5 ARP 4 DRA 3 DA 2 DRD 1 DRN 0 FL * Bit [1]: Bit [2]: * * 1 - Enable fast learning mode. In this mode, the hardware learns all the new MAC addresses at highest rate, and reports to the CPU while the hardware scans the MAC database. When the CPU report queue is full, the MAC address is learned and marked as "Not reported". When the hardware scans the database and finds a MAC address marked as "Not Reported" it tries to report it to the CPU. The scan rate must be set. SCAN Control register sets the scan rate. (Default 0) 0 - Search Engine learns a new MAC address and sends a message to the CPU report queue. If queue is full, the learning is temporarily halted. 1 - Disable report new VLAN port association (Default 0) 0 - Report new VLAN port association Report control * * 1 - Disable report MAC address deletion (Default 0) 0 - Report MAC address deletion (MAC address is deleted from MCT after aging time) Bit [3]: Delete Control * 1 - Disable aging logic from removing MAC during aging (Default 0) * 0 - MAC address entry is removed when it is old enough to be aged. However, a report is still sent to the CPU in both cases, when bit[2] = 0 Bit [4]: * * * * 1 - Disable report aging VLAN port association (Default 0) 0 - Enable Report aging VLAN. VLAN is not removed by hardware. The CPU needs to remove the VLAN -port association. 1 - Report ARP packet to CPU (Default 0) Disable MCT speedup aging (Default 0) * 1 - Disable speedup aging when MCT resource is low. * 0 - Enable speedup aging when MCT resource is low. Bit [5]: Bit [6]: 76 Zarlink Semiconductor Inc. Data Sheet Bit [7]: * Slow Learning (Default 0) MVTX2804 * 1- Enable slow learning. Learning is temporary disabled when search demand is high * 0 - Learning is performed independent of search demand 11.8.1.5 * * SCAN - SCAN CONTROL REGISTER CPU Address:h404 Accessed by CPU (R/W) 7 R 6 Ratio 0 SCAN is used when fast learning is enabled (SE_OP MODE bit 0). It is used for setting up the report rate for newly learned MAC addresses to the CPU. Bit [6:0]: Bit [7]: Examples: R= 0, Ratio = 0: R= 0, Ratio = 1: R= 1, Ratio = 7: R= 0, Ratio = 7: All aging rounds are used for aging Aging and scanning in every other aging round In eight rounds, one is used for scanning and seven is used for aging In eight rounds, one is used for aging and seven is used for scanning * * Ratio between database scanning and aging round (Default 00) Reverse the ratio between scanning round and aging round (Default 0) 11.9 11.9.1 11.9.1.1 * I 2C Group 5 Address Buffer Control/QOS Group FCBAT - FCB AGING TIMER Address h03E; CPU Address:h500 7 FCBAT Bit [7:0]: * * FCB Aging time. Unit of 1ms. (Default FF) FCBAT define the aging time out interval of FCB handle 0 11.9.1.2 * * I 2C QOSC - QOS CONTROL Address h03F; CPU Address:h501 Accessed by CPU, serial interface and I2C (R/W) 7 Tos-d Bit [0]: * 6 Tos-p 5 CPUQ 4 VF1c 3 1 0 QoS frame lost is OK. Priority will be available for flow control enabled source only when this bit is set (Default 0) Zarlink Semiconductor Inc. 77 MVTX2804 Bit [4]: * Per VLAN Multicast Flow Control (Default 0) * 0 - Disable * 1 - Enable Data Sheet Bit [5]: * CPU multicast queues size * 0 = 16 entries * 1 = 160 entries Bit [6]: * Select TOS bits for Priority (Default 0) * 0 - Use TOS [4:2] bits to map the transmit priority * 1 - Use TOS [5:3] bits to map the transmit priority Bit [7]: * select TOS bits for Drop (Default 0) * 0 - Use TOS [4:2] bits to map the drop priority * 1 - Use TOS [5:3] bits to map the drop priority 11.9.1.3 * * I 2C FCR - FLOODING CONTROL REGISTER Address h040; CPU Address:h502 Accessed by CPU, serial interface and I2C (R/W) 7 Tos Bit [3:0]: * 6 5 4 3 U2MR 0 TimeBase U2MR: Unicast to Multicast Rate. Units in terms of time base defined in bits [6:4]. This is used to limit the amount of flooding traffic. The value in U2MR specifies how many packets are allowed to flood within the time specified by bit [6:4]. To disable this function, program U2MR to 0. (Default = 4'h8) TimeBase: (Default = 000) * * * * * * * * 000 = 10us 001 = 20us 010 = 40us 011 = 80us 100 = 160us 01 = 320us 110 = 640us 111 = 10us, same as 000. Bit [6:4]: * Bit [7]: * Select VLAN tag or TOS field (IP packets) to be preferentially picked to map transmit priority and drop priority (Default = 0). * 0 - Select VLAN tag priority field over TOS field * 1 - Select TOS field over VLAN tag priority field 11.9.1.4 * * I 2C AVPML - VLAN PRIORITY MAP Address h041; CPU Address:h503 Accessed by CPU, serial interface and I2C (R/W) 7 VP2 6 5 VP1 3 2 VP0 0 Registers AVPML, AVPMM, and AVPMH allow the eight VLAN priorities to map into eight internal level transmit priorities. Under the internal transmit priority, "seven" is the highest priority where as "zero" is the lowest. This feature allows the user the flexibility of redefining the VLAN priority field. For example, programming a value of 78 Zarlink Semiconductor Inc. Data Sheet MVTX2804 7 into bit 2:0 of the AVPML register would map packet VLAN priority) into internal transmit priority 7. The new priority is used only inside the 2804. When the packet goes out it carries the original priority. Bit [2:0]: Bit [5:3]: Bit [7:6]: * * * Mapped priority of 0 (Default 000) Mapped priority of 1 (Default 001) Mapped priority of 2 (Default 10) 11.9.1.5 * * AVPMM - VLAN PRIORITY MAP I2C Address h042, CPU Address:h504 Accessed by CPU, serial interface and I2C (R/W) 7 VP5 6 VP4 4 3 VP3 1 VP2 0 Map VLAN priority into eight level transmit priorities: Bit [0]: Bit [3:1]: Bit [6:4]: Bit [7]: * * * * Mapped priority of 2 (Default 0) Mapped priority of 3 (Default 011) Mapped priority of 4 (Default 100) Mapped priority of 5 (Default 1) 11.9.1.6 * * AVPMH - VLAN PRIORITY MAP I2C Address h043, CPU Address:h505 Accessed by CPU, serial interface and I2C (R/W) 7 VP2 5 4 VP6 2 1 VP5 0 Map VLAN priority into eight level transmit priorities: Bit [1:0]: Bit [4:2]: Bit [7:5]: * * * Mapped priority of 5 (Default 10) Mapped priority of 6 (Default 110) Mapped priority of 7 (Default 111) 11.9.1.7 * * 2 TOSPML - TOS PRIORITY MAP I C Address h044, CPU Address:h506 Accessed by CPU, serial interface and I2C (R/W) 7 TP2 6 5 TP1 3 2 TP0 0 Map TOS field in IP packet into four level transmit priorities Bit [2:0]: * Mapped priority when TOS is 0 (Default 000) Zarlink Semiconductor Inc. 79 MVTX2804 Bit [5:3]: Bit [7:6] * * Mapped priority when TOS is 1 (Default 001) Mapped priority when TOS is 2 (Default 10) Data Sheet 11.9.1.8 * * TOSPMM - TOS PRIORITY MAP I2C Address h045, CPU Address:h507 Accessed by CPU, serial interface and I2C (R/W) 7 6 TP5 5 TP4 4 3 TP3 1 TP2 0 Map TOS field in IP packet into four level transmit priorities Bit [0]: Bit [3:1]: Bit [6:4]: Bit [7]: * * * * Mapped priority when TOS is 2 (Default 0) Mapped priority when TOS is 3 (Default 011) Mapped priority when TOS is 4 (Default 100) Mapped priority when TOS is 5 (Default 1) 11.9.1.9 * * I 2C TOSPMH - TOS PRIORITY MAP Address h046, CPU Address:h508 Accessed by CPU, serial interface and I2C (R/W) 7 TP7 54 TP6 21 TP5 0 Map TOS field in IP packet into four level transmit priorities: Bit [1:0]: Bit [4:2]: Bit [7:5]: * * * Mapped priority when TOS is 5 (Default 01) Mapped priority when TOS is 6 (Default 110) Mapped priority when TOS is 7 (Default 111) 11.9.1.10 AVDM - VLAN DISCARD MAP * * I2C Address h047, CPU Address:h509 Accessed by CPU, serial interface and I2C (R/W) 7 FDV7 6 FDV6 5 FDV5 4 FDV4 3 FDV3 2 FDV2 1 FDV1 0 FDV0 Map VLAN priority into frame discard when low priority buffer usage is above threshold. Frames with high discard (drop) priority will be discarded (dropped) before frames with low drop priority. * * 0 - Low discard priority 1 - High discard priority Bit [0]: Bit [1]: Bit [2]: * * * Frame discard priority for frames with VLAN transmit priority 0 (Default 0) Frame discard priority for frames with VLAN transmit priority 1 (Default 0) Frame discard priority for frames with VLAN transmit priority 2 (Default 0) 80 Zarlink Semiconductor Inc. Data Sheet Bit [3]: Bit [4]: Bit [5]: Bit [6]: Bit [7]: * * * * * MVTX2804 Frame discard priority for frames with VLAN transmit priority 3 (Default 0) Frame discard priority for frames with VLAN transmit priority 4 (Default 0) Frame discard priority for frames with VLAN transmit priority 5 (Default 0) Frame discard priority for frames with VLAN transmit priority 6 (Default 0) Frame discard priority for frames with VLAN transmit priority 7 (Default 0) 11.9.1.11 TOSDML - TOS DISCARD MAP * * I2C Address h048, CPU Address:h50A Accessed by CPU, serial interface and I2C (R/W) 7 FDT7 6 FDT6 5 FDT5 4 FDT4 3 FDT3 2 FDT2 1 FDT1 0 FDT0 Map TOS into frame discard when low priority buffer usage is above threshold Bit [0]: Bit [1]: Bit [2]: Bit [3]: Bit [4]: Bit [5]: Bit [6]: Bit [7]: Frame discard priority for frames with TOS transmit priority 0 (Default 0) Frame discard priority for frames with TOS transmit priority 1 (Default 0) Frame discard priority for frames with TOS transmit priority 2 (Default 0) Frame discard priority for frames with TOS transmit priority 3 (Default 0) Frame discard priority for frames with TOS transmit priority 4 (Default 0) Frame discard priority for frames with TOS transmit priority 5 (Default 0) Frame discard priority for frames with TOS transmit priority 6 (Default 0) Frame discard priority for frames with TOS transmit priority 7 (Default 0) 11.9.2 * * I 2C BMRC - Broadcast/Multicast Rate Control Address h049, CPU Address:h50B) Accessed by CPU, serial interface and I2C (R/W) 7 Broadcast Rate 4 3 0 Multicast Rate This broadcast and multicast rate defines for each port the number of incoming packet allowed to be forwarded within a specified time. Once the packet rate is reached, packets will be dropped. To turn off the rate limit, program the field to 0. Bit [3:0]: Bit [7:4]: Multicast Rate Control Number of multicast packets allowed within the time defined in bits 6 to 4 of the Flooding Control Register (FCR). (Default 0). Broadcast Rate Control Number of broadcast packets allowed within the time defined in bits 6 to 4 of the Flooding Control Register (FCR). (Default 0) 11.9.3 * * UCC - Unicast Congestion Control I2C Address h04A, CPU Address:h50C Accessed by CPU, serial interface and I2C (R/W) 7 0 Zarlink Semiconductor Inc. 81 MVTX2804 Unicast congest threshold Bit [7:0]: Data Sheet Number of frame count. Used for best effort dropping at B% when destination port's best effort queue reaches UCC threshold and shared pool is all in use. Granularity 16 frame. (Default: h07) 82 Zarlink Semiconductor Inc. Data Sheet 11.9.4 * * MVTX2804 MCC - Multicast Congestion Control I2C Address h0B7, CPU Address:h50D Accessed by CPU, serial interface and I2C (R/W) 7 FC reaction prd Bit [3:0]: Bit [4]: Bit [7:5]: 0 Multicast congest threshold In multiples of two. Used for triggering MC flow control when destination port's multicast best effort queue reaches MCC threshold. (Default 5'h08) Must be 0 Flow control reaction period. ([7:5] *4 uSec)+3 uSec (Default 3'h2). 11.9.5 * * PRG - Port Reservation for Giga ports I2C Address h0B9, CPU Address:h50F Accessed by CPU, serial interface and I2C (R/W) 7 Buffer low thd Bit [3:0]: 7 7 Per source buffer Reservation 0 Per source buffer reservation. Define the space in the FDB reserved for each port. Expressed in multiples of 16 packets. For each packet 1536 bytes are reserved in the memory. Default: 4'hA for 4MB memory 4'h6 for 2MB memory 4'h3 for 1MB memory Bits [7:4]: Expressed in multiples of 16 packets. Threshold for dropping all best effort frames when destination port best effort queues reach UCC threshold and shared pool is all used and source port reservation is at or below the PRG[7:4] level. Also the threshold for initiating UC flow control. Default: 4'h6 for 4MB memory 4'h2 for 2MB memory 4'h1 for 1MB memory 11.9.6 11.9.6.1 * * FCB Reservation SFCB - SHARE FCB SIZE I2C Address h04E), CPU Address:h510 Accessed by CPU, serial interface and I2C (R/W) 7 Shared buffer size 0 Zarlink Semiconductor Inc. 83 MVTX2804 Bits [7:0]: * Expressed in multiples of 8. Buffer reservation for shared pool. (Default 4G & 4M = 8'd62) (Default 4G & 2M = 8'd20) (Default 4G & 1M = 8'd08 (Default 8G & 4M = 8'd150) (Default 8G & 2M = 8'd55) (Default 8G & 1M = 8'd25 Data Sheet 84 Zarlink Semiconductor Inc. Data Sheet 11.9.6.2 * * MVTX2804 C2RS - CLASS 2 RESERVED SIZE I2C Address h04F, CPU Address:h511 Accessed by CPU, serial interface and I2C (R/W) 7 Class 2 FCB Reservation Bits [7:0]: * Buffer reservation for class 2 (third lowest priority). Granularity 2. (Default 8'h00) 0 11.9.6.3 * * 2 C3RS - CLASS 3 RESERVED SIZE I C Address h050, CPU Address:h512 Accessed by CPU, serial interface and I2C (R/W) 7 Class 3 FCB Reservation Bits [7:0]: * Buffer reservation for class 3. Granularity 2. (Default 8'h00) 0 11.9.6.4 * * C4RS - CLASS 4 RESERVED SIZE I2C Address h051, CPU Address:h513 Accessed by CPU, serial interface and I2C (R/W) 7 Class 4 FCB Reservation Bits [7:0]: * Buffer reservation for class 4. Granularity 2. (Default 8'h00) 0 11.9.6.5 * * C5RS - CLASS 5 RESERVED SIZE I2C Address h052; CPU Address:h514 Accessed by CPU, serial interface and I2C (R/W) 7 Class 5 FCB Reservation Bits [7:0]: * Buffer reservation for class 5. Granularity 2. (Default 8'h00) 0 11.9.6.6 * * I 2C C6RS - CLASS 6 RESERVED SIZE Address h053; CPU Address:h515 Accessed by CPU, serial interface and I2C (R/W) 7 Class 6 FCB Reservation Bits [7:0]: * Buffer reservation for class 6 (second highest priority). Granularity 2. (Default 8'h00) 0 Zarlink Semiconductor Inc. 85 MVTX2804 11.9.6.7 * * Data Sheet C7RS - CLASS 7 RESERVED SIZE I2C Address h054; CPU Address:h516 Accessed by CPU, serial interface and I2C (R/W) 7 Class 7 FCB Reservation Bits [7:0]: * Buffer reservation for class 7 (highest priority). Granularity 2. 8'h00) (Default 0 11.9.7 * Classes Byte Gigabit Port 0 Accessed by CPU; serial interface and I2C (R/W): 11.9.7.1 * QOSC00 - BYTE_C2_G0 I2C Address h055, CPU Address:h517 Bits [7:0]: * * * Byte count threshold for C2 queue WRED (Default 8'h28) (1024byte/unit when Delay Bound is used) (1024byte/unit when WFQ is used) 11.9.7.2 * I 2C QOSC01 - BYTE_C3_G0 Address h056, CPU Address:h518 Bits [7:0]: * * * Byte count threshold for C3 queue WRED (Default 8'h28) (512byte/unit when Delay Bound is used) (1024byte/unit when WFQ is used) 11.9.7.3 * QOSC02 - BYTE_C4_G0 I2C Address h057, CPU Address:h519 Bits [7:0]: * * * Byte count threshold for C4 queue WRED (Default 8'h28) (256byte/unit when Delay Bound is used) (1024byte/unit when WFQ is used) 11.9.7.4 * QOSC03 - BYTE_C5_G0 I2C Address h058, CPU Address:h51A Bits [7:0]: * * * Byte count threshold for C5 queue WRED (Default 8'h28) (128byte/unit when Delay Bound is used) (1024byte/unit when WFQ is used) 11.9.7.5 * I 2C QOSC04 - BYTE_C6_G0 Address h059, CPU Address:h51B Bits [7:0]: * * * Byte count threshold for C6 queue WRED (Default 8'h50) (64byte/unit when Delay Bound is used) (1024byte/unit when WFQ is used) 86 Zarlink Semiconductor Inc. Data Sheet 11.9.7.6 * MVTX2804 QOSC05 - BYTE_C7_G0 I2C Address h05A, CPU Address:h51C Bits [7:0]: * * * Byte count threshold for C6 queue WRED (Default 8'h50) (64byte/unit when Delay Bound is used) (1024byte/unit when WFQ is used) QOSC00 through QOSC05 represent the values F-A in Table 3 for Gigabit port 0. They are per-queue byte thresholds for weighted random early drop (WRED). QOSC05 represents A, and QOSC00 represents F. See QoS application note for more information. 11.9.8 * Classes Byte Gigabit Port 1 Accessed by CPU; serial interface and I2C (R/W): 11.9.8.1 * I 2C QOSC06 - BYTE_C2_G1 Address h05B, CPU Address:h51D Bits [7:0]: * * * Byte count threshold for C2 queue WRED (Default 8'h28) (1024byte/unit when Delay Bound is used) (1024byte/unit when WFQ is used) 11.9.8.2 * QOSC07 - BYTE_C3_G1 I2C Address h05C, CPU Address:h51E Bits [7:0]: * * * Byte count threshold for C3 queue WRED (Default 8'h28) (512 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.8.3 * I 2C QOSC08 - BYTE_C4_G1 Address h05D, CPU Address:h51F Bits [7:0]: * * * Byte count threshold for C4 queue WRED (Default 8'h28) (256 byte/unit when Delay Bound is used) (1024byte/unit when WFQ is used) 11.9.8.4 * QOSC09 - BYTE_C5_G1 I2C Address h05E, CPU Address:h520 Bits [7:0]: * * * Byte count threshold for C5 queue WRED (Default 8'h28) (128 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.8.5 * 2 QOSC0A - BYTE_C6_G1 I C Address h05F, CPU Address:h521 Bits [7:0]: * * * Byte count threshold for C6 queue WRED (Default 8'h50) (64 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) Zarlink Semiconductor Inc. 87 MVTX2804 11.9.8.6 * Data Sheet QOSC0B - BYTE_C7_G1 I2C Address h060, CPU Address:h522 Bits [7:0]: * * * Byte count threshold for C7 queue WRED (Default 8'h50) (64 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) QOSC06 through QOSC0B represent the values F-A in Table 3. They are per-queue byte thresholds for random early drop. QOSC0B represents A, and QOSC06 represents F. See QoS application note for more information 11.9.9 * Classes Byte Gigabit Port 2 Accessed by CPU; serial interface and I2C (R/W): 11.9.9.1 * QOSC0C - BYTE_C2_G2 I2C Address h061, CPU Address:h523 Bits [7:0]: * * * Byte count threshold for C2 queue WRED (Default 8'h28) (1024 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.9.2 * I 2C QOSC0D - BYTE_C3_G2 Address h062, CPU Address:h524 Bits [7:0]: * * * Byte count threshold for C3 queue WRED (Default 8'h28) (512 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.9.3 * QOSC0E - BYTE_C4_G2 I2C Address h063, CPU Address:h525 Bits [7:0]: * * * Byte count threshold for C4 queue WRED (Default 8'h28) (256 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.9.4 * I 2C QOSC0F - BYTE_C5_G2 Address h064, CPU Address:h526 Bits [7:0]: * * * Byte count threshold for C5 queue WRED (Default 8'h28) (128 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.9.5 * 2 QOSC10 - BYTE_C6_G2 I C Address h065, CPU Address:h527 Bits [7:0]: * * * Byte count threshold for C6 queue WRED (Default 8'h50) (64 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 88 Zarlink Semiconductor Inc. Data Sheet 11.9.9.6 * MVTX2804 QOSC11 - BYTE_C7_G2 I2C Address h066, CPU Address:h528 Bits [7:0]: * * * Byte count threshold for C7 queue WRED (Default 8'h50) (64 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) QOSC0C through QOSC11 represent the values F-A in Table 3. They are per-queue byte thresholds for random early drop. QOSC11 represents A, and QOSC0C represents F. See QoS application note for more information 11.9.10 Classes Byte Gigabit Port 3 * Accessed by CPU; serial interface and I2C (R/W): 11.9.10.1 QOSC12 - BYTE_C2_G3 * I2C Address h067, CPU Address:h529 Bits [7:0]: * * * Byte count threshold for C2 queue WRED (Default 8'h28) (1024 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.10.2 QOSC13 - BYTE_C3_G3 * I2C Address h068, CPU Address:h52A Bits [7:0]: * * * Byte count threshold for C3 queue WRED (Default 8'h28) (512 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.10.3 QOSC14 - BYTE_C4_G3 * I2C Address h069, CPU Address:h52B Bits [7:0]: * * * Byte count threshold for C4 queue WRED (Default 8'h28) (256 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.10.4 QOSC15 - BYTE_C5_G3 * I2C Address h06A, CPU Address:h52C Bits [7:0]: * * * Byte count threshold for C5 queue WRED (Default 8'h28) (128 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.10.5 QOSC16 - BYTE_C6_G3 * I2C Address h06B, CPU Address:h52D Bits [7:0]: * * * Byte count threshold for C6 queue WRED (Default 8'h50) (64 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) Zarlink Semiconductor Inc. 89 MVTX2804 11.9.10.6 QOSC17 - BYTE_C7_G3 * I2C Address h06C, CPU Address:h52E Bits [7:0]: * * * Byte count threshold for C7 queue WRED (Default 8'h50) (64 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) Data Sheet QOSC12 through QOSC17 represent the values F-A in Table 3. They are per-queue byte thresholds for random early drop. QOSC17 represents A, and QOSC12 represents F. See QoS application note for more information 11.9.11 Classes Byte Gigabit Port 4 * Accessed by CPU; serial interface and I2C (R/W): 11.9.11.1 QOSC18 - BYTE_C2_G4 * I2C Address h06D, CPU Address:h52F Bits [7:0]: * * * Byte count threshold for C2 queue WRED (Default 8'h28) (1024 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.11.2 QOSC019 - BYTE_C3_G4 * I2C Address h06E, CPU Address:h530 Bits [7:0]: * * * Byte count threshold for C3 queue WRED (Default 8'h28) (512 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.11.3 QOSC1A - BYTE_C4_G4 * I2C Address h06F, CPU Address:h531 Bits [7:0]: * * * Byte count threshold for C4 queue WRED (Default 8'h28) (256 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.11.4 QOSC1B - BYTE_C5_G4 * I2C Address h070, CPU Address:h532 Bits [7:0]: * * * Byte count threshold for C5 queue WRED (Default 8'h28) (128 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.11.5 QOSC1C - BYTE_C6_G4 * I2C Address h071, CPU Address:h533 Bits [7:0]: * * * Byte count threshold for C6 queue WRED (Default 8'h28) (64 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 90 Zarlink Semiconductor Inc. Data Sheet 11.9.11.6 QOSC1D- BYTE_C7_G4 * I2C Address h072, CPU Address:h534 Bits [7:0]: * * * Byte count threshold for C7 queue WRED (Default 8'h28) (64 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) MVTX2804 QOSC18 through QOSC1D represent the values F-A in Table 3. They are per-queue byte thresholds for random early drop. QOSC1D represents A, and QOSC18 represents F. See QoS application note for more information 11.9.12 Classes Byte Gigabit Port 5 * Accessed by CPU; serial interface and I2C (R/W): 11.9.12.1 QOSC1E- BYTE_C2_G5 * I2C Address h073, CPU Address:h535 Bits [7:0]: * * * Byte count threshold for C2 queue WRED (Default 8'h28) (1024 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.12.2 QOSC1F - BYTE_C3_G5 * I2C Address h074, CPU Address:h536 Bits [7:0]: * * * Byte count threshold for C3 queue WRED (Default 8'h28) (512 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.12.3 QOSC20 - BYTE_C4_G5 * I2C Address h075, CPU Address:h537 Bits [7:0]: * * * Byte count threshold for C4 queue WRED (Default 8'h28) (256 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.12.4 QOSC21 - BYTE_C5_G5 * I2C Address h076, CPU Address:h538 Bits [7:0]: * * * Byte count threshold for C5 queue WRED (Default 8'h28) (128 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.12.5 QOSC22 - BYTE_C6_G5 * I2C Address h077, CPU Address:h539 Bits [7:0]: * * * Byte count threshold for C6 queue WRED (Default 8'h50) (64 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) Zarlink Semiconductor Inc. 91 MVTX2804 11.9.12.6 QOSC23 - BYTE_C7_G5 * I2C Address h078, CPU Address:h53A Bits [7:0]: * * * Byte count threshold for C4 queue WRED (Default 8'h50) (64 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) Data Sheet QOSC1E through QOSC23 represent the values F-A in Table 3. They are per-queue byte thresholds for random early drop. QOSC23 represents A, and QOSC1E represents F. See QoS application note for more information 11.9.13 Classes Byte Gigabit Port 6 * Accessed by CPU; serial interface and I2C (R/W): 11.9.13.1 QOSC24 - BYTE_C2_G6 * I2C Address h079, CPU Address:h53B Bits [7:0]: * * * Byte count threshold for C2 queue WRED (Default 8'h28) (1024 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.13.2 QOSC25 - BYTE_C3_G6 * I2C Address h07A, CPU Address:h53C Bits [7:0]: * * * Byte count threshold for C3 queue WRED (Default 8'h28) (512 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.13.3 QOSC26 - BYTE_C4_G6 * I2C Address h07B, CPU Address:h53D Bits [7:0]: * * * Byte count threshold for C4 queue WRED (Default 8'h28) (256 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.13.4 QOSC27 - BYTE_C5_G6 * I2C Address h07C, CPU Address:h53E Bits [7:0]: * * * Byte count threshold for C5 queue WRED (Default 8'h28) (128 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.13.5 QOSC28 - BYTE_C6_G6 * I2C Address h07D, CPU Address:h53F Bits [7:0]: * * * Byte count threshold for C6 queue WRED (Default 8'h50) (64 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 92 Zarlink Semiconductor Inc. Data Sheet 11.9.13.6 QOSC29 - BYTE_C7_G6 * I2C Address h07E, CPU Address:h540 Bits [7:0]: * * * Byte count threshold for C7 queue WRED (Default 8'h50) (64 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) MVTX2804 QOSC24 through QOSC29 represent the values F-A in Table 3. They are per-queue byte thresholds for random early drop. QOSC29 represents A, and QOSC24 represents F. See QoS application note for more information. 11.9.14 Classes Byte Gigabit Port 7 * Accessed by CPU; serial interface and I2C (R/W): 11.9.14.1 QOSC2A - BYTE_C2_G7 * I2C Address h07F, CPU Address:h541 Bits [7:0]: * * * Byte count threshold for C2 queue WRED (Default 8'h28) (1024 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.14.2 QOSC2B - BYTE_C3_G7 * I2C Address h080, CPU Address:h542 Bits [7:0]: * * * Byte count threshold for C3 queue WRED (Default 8'h28) (512 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.14.3 QOSC2C - BYTE_C4_G7 * I2C Address h081, CPU Address:h543 Bits [7:0]: * * * Byte count threshold for C4 queue WRED (Default 8'h28) (256 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.14.4 1QOSC2D - BYTE_C5_G7 * I2C Address h082, CPU Address:h544 Bits [7:0]: * * * Byte count threshold for C5 queue WRED (Default 8'h28) (128 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) 11.9.14.5 QOSC2E - BYTE_C6_G7 * I2C Address h083, CPU Address:h545 Bits [7:0]: * * * Byte count threshold for C6 queue WRED (Default 8'h50) (64 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) Zarlink Semiconductor Inc. 93 MVTX2804 11.9.14.6 QOSC2F - BYTE_C7_G7 * I2C Address h084, CPU Address:h546 Bits [7:0]: * * * Byte count threshold for C5 queue WRED (Default 8'h50) (64 byte/unit when Delay Bound is used) (1024 byte/unit when WFQ is used) Data Sheet QOSC00 through QOSC05 represent the values F-A in Table 3. They are per-queue byte thresholds for random early drop. QOSC05 represents A, and QOSC00 represents F. See QoS application note for more information. 11.9.15 Classes Byte Limit CPU * Accessed by CPU; serial interface and I2C (R/W): 11.9.15.1 QOSC30 - BYTE_C01 * CPU Address:h547 Bits [7:0]: * Byte count threshold for C1 queue (256byte/unit) 11.9.15.2 QOSC31 - BYTE_C02 * CPU Address:h548 Bits [7:0]: * Byte count threshold for C2 queue (256byte/unit) 11.9.15.3 QOSC32 - BYTE_C03 * CPU Address:h549 Bits [7:0]: * Byte count threshold for C3 queue (256byte/unit) QOSC30 through QOSC32 represent the values C-A for CPU port. The values A-C are per-queue byte thresholds for random early drop. QOSC32 represents A, and QOSC30 represents C. Queue 0 does not have weighted random drop. See QoS application note for more information. 11.9.16 Classes WFQ Credit Set 0 * Accessed by CPU only 11.9.16.1 QOSC33 - CREDIT_C0_G0 * CPU Address:h54A Bits [5:0]: Bits [7:6]: * * * W0 - Credit register for WFQ. (Default 6'h04) Priority type. Define one of the four QoS mode of operation for port 0 (Default 2'00) See table below: Queue Option 1 Bit [7:6] = 2'B00 Option 2 Bit [7:6] = 2'B01 Option 3 Bit [7:6] = 2'B10 Option 4 Bit [7:6] = 2'B11 P7 P6 P5 P4 P3 P2 P1 BE BE P0 DELAY BOUND SP SP WFQ DELAY BOUND WFQ 94 Zarlink Semiconductor Inc. Data Sheet Queue Credit for WFQ - Bit [5:0] P7 W7 P6 W6 P5 W5 P4 W4 P3 W3 P2 W2 MVTX2804 P1 W1 P0 W0 11.9.16.2 QOSC34 - CREDIT_C1_G0 * CPU Address:h54B Bits [7]: * Flow control allow during WFQ scheme. (Default 1'b1) * 0 = Not support QoS when the Source port Flow control status is on. * 1= Always support QoS) Bits [6]: * Flow control BE Queue only. (Default 1'b1) * 0= DO NOT send any frames if the XOFF is on. * 1= the P7-P2 frames can be sent even the XOFF is ON Bits [5:0] Fc_allow * W1 - Credit register. (Default 4'h04) Lost_ok Ingress- for src fc status 0 1 0 1 0 1 Go to BE Queue if (Src FC or Des FC on) otherwise Normal Go to BE Queue if (Dest FC on) otherwise Normal (WFQ only) Go to BE Queue if (Src FC on) otherwise BAD (WFQ only) Always Normal Go to BE Queue if (Src FC on) Always Normal Fc_be_only Egress- for dest fc_status 0 0 1 1 X X 0 0 0 0 1 1 11.9.16.3 QOSC35 - CREDIT_C2_G0 * CPU Address:h54C Bits [5:0]: Bits [7:6]: * * W2 - Credit register. (Default 4'h04) Reserved 11.9.16.4 QOSC36 - CREDIT_C3_G0 * CPU Address:h54D Bits [5:0]: Bits [7:6]: * * W3 - Credit register. (Default 4'h04) Reserved 11.9.16.5 QOSC37 - CREDIT_C4_G0 * CPU Address:h54E Bits [5:0]: Bits [7:6]: * * W4 - Credit register. (Default 4'h04) Reserved Zarlink Semiconductor Inc. 95 MVTX2804 11.9.16.6 QOSC38 - CREDIT_C5_G0 * CPU Address:h54F Bits [5:0]: Bits [7:6]: * * W5 - Credit register. (Default 5'h8) Reserved Data Sheet 11.9.16.7 QOSC39- CREDIT_C6_G0 * CPU Address:h550 Bits [5:0]: Bits [7:6]: * * W6 - Credit register. (Default 5'h8) Reserved 11.9.16.8 QOSC3A- CREDIT_C7_G0 * CPU Address:h551 Bits [5:0]: Bits [7:6]: * * W7 - Credit register. (Default 5'h10) Reserved QOSC33 through QOSC3Arepresents the set of WFQ parameters (see section 7.5) for Gigabit port 0. The granularity of the numbers is 1, and their sum must be 64. QOSC33 corresponds to W0, and QOSC3A corresponds to W7. 11.9.17 Classes WFQ Credit Port G1 * Access by CPU only 11.9.17.1 QOSC3B - CREDIT_C0_G1 * CPU Address:h552 Bits [5:0]: Bits [7:6]: * * * W0 - Credit register for WFQ. (Default 6'h04) Priority type. Define one of the four QoS mode of operation for port 1 (Default 2'00) See table below: Queue P7 P6 P5 P4 P3 P2 P1 P0 Option 1 Bit [7:6] = 2'B00 Option 2 Bit [7:6] = 2'B01 Option 3 Bit [7:6] = 2'B10 Option 4 Bit [7:6] = 2'B11 Credit for WFQ - Bit [5:0] DELAY BOUND SP SP WFQ W7 W6 W5 W4 W3 W2 DELAY BOUND WFQ BE BE W1 W0 96 Zarlink Semiconductor Inc. Data Sheet 11.9.17.2 QOSC3C - CREDIT_C1_G1 * CPU Address:h54B Bits [7]: * Flow control allow during WFQ scheme. (Default 1'b1) * 0 = Not support QoS when the Source port Flow control status is on. * 1= Always support QoS) MVTX2804 Bits [6]: * Flow control BE Queue only. (Default 1'b1) * 0= DO NOT send any frames if the XOFF is on. * 1= the P7-P2 frames can be sent even the XOFF is ON Bits [5:0] * W1 - Credit register. (Default 4'h04) Fc_allow Fc_be_only Lost_ok Ingressfor src fc status 0 1 0 1 0 1 Go to BE Queue if (Src FC or Des FC on) otherwise Normal Go to BE Queue if (Dest FC on) otherwise Normal (WFQ only) Go to BE Queue if (Src FC on) otherwise BAD (WFQ only) Always Normal Go to BE Queue if (Src FC on) Always Normal Egress- for dest fc_status 0 0 1 1 X X 0 0 0 0 1 1 11.9.17.3 QOSC3D - CREDIT_C2_G1 * CPU Address:h553 Bits [5:0]: Bits [7:6]: * * W2 - Credit register. (Default 4'h04) Reserved 11.9.17.4 QOSC3E - CREDIT_C3_G1 * CPU Address:h554 Bits [5:0]: Bits [7:6]: * * W3 - Credit register. (Default 4'h04) Reserved 11.9.17.5 QOSC3F - CREDIT_C4_G1 * CPU Address:h555 Bits [5:0]: Bits [7:6]: * * W4 - Credit register. (Default 4'h04) Reserved Zarlink Semiconductor Inc. 97 MVTX2804 11.9.17.6 QOSC40 - CREDIT_C5_G1 * CPU Address:h556 Bits [5:0]: Bits [7:6]: * * W5 - Credit register. (Default 5'h8) Reserved Data Sheet 11.9.17.7 QOSC41- CREDIT_C6_G1 * CPU Address:h557 Bits [5:0]: Bits [7:6]: * * W6 - Credit register. (Default 5'h8) Reserved 11.9.17.8 QOSC42- CREDIT_C7_G1 * CPU Address:h558 Bits [5:0]: Bits [7:6]: * * W7 - Credit register. (Default 5'h10) Reserved QOSC3B through QOSC42 represents the set of WFQ parameters (see section 7.5) for Gigabit port 1. The granularity of the numbers is 1, and their sum must be 64. QOSC3B corresponds to W0, and QOSC42 corresponds to W7 11.9.18 Classes WFQ Credit Port G2 * Access by CPU only 11.9.18.1 QOSC43 - CREDIT_C0_G2 * CPU Address:h55A Bits [5:0]: Bits [7:6]: * * * W0 - Credit register for WFQ. (Default 6'h04) Priority type. Define one of the four QoS mode of operation for port 2 (Default 2'00) See table below: Queue Option 1 Bit [7:6] = 2'B00 Option 2 Bit [7:6] = 2'B01 Option 3 Bit [7:6] = 2'B10 Option 4 Bit [7:6] = 2'B11 Credit for WFQ - Bit [5:0] P7 P6 P5 P4 P3 P2 P1 BE BE DELAY BOUND SP SP WFQ W7 W6 W5 W4 W3 W2 DELAY BOUND WFQ W1 W0 98 Zarlink Semiconductor Inc. Data Sheet 11.9.18.2 QOSC44 - CREDIT_C1_G2 * CPU Address:h55B Bits [7]: * Flow control allow during WFQ scheme. (Default 1'b1) * 0 = Not support QoS when the Source port Flow control status is on. * 1= Always support QoS) MVTX2804 Bits [6]: * Flow control BE Queue only. (Default 1'b1) * 0= DO NOT send any frames if the XOFF is on. * 1= the P7-P2 frames can be sent even the XOFF is ON Bits [5:0] * W1 - Credit register. (Default 4'h04) Fc_allow Fc_be_only Lost_ok Ingressfor src fc status 0 1 0 1 0 1 Go to BE Queue if (Src FC or Des FC on) otherwise Normal Go to BE Queue if (Dest FC on) otherwise Normal (WFQ only) Go to BE Queue if (Src FC on) otherwise BAD (WFQ only) Always Normal Go to BE Queue if (Src FC on) Always Normal Egress- for dest fc_status 0 0 1 1 X X 0 0 0 0 1 1 11.9.18.3 QOSC45 - CREDIT_C2_G2 * CPU Address:h55C Bits [5:0]: Bits [7:6]: * * W2 - Credit register. (Default 4'h04) Reserved 11.9.18.4 QOSC46 - CREDIT_C3_G2 * CPU Address:h55D Bits [5:0]: Bits [7:6]: * * W3 - Credit register. (Default 4'h04) Reserved 11.9.18.5 QOSC47 - CREDIT_C4_G2 * CPU Address:h55E Bits [5:0]: Bits [7:6]: * * W4 - Credit register. (Default 4'h04) Reserved Zarlink Semiconductor Inc. 99 MVTX2804 11.9.18.6 QOSC48 - CREDIT_C5_G2 * CPU Address:h55F Bits [5:0]: Bits [7:6]: * * W5 - Credit register. (Default 5'h8) Reserved Data Sheet 11.9.18.7 QOSC49- CREDIT_C6_G2 * CPU Address:h560 Bits [5:0]: Bits [7:6]: * * W6 - Credit register. (Default 5'h8) Reserved 11.9.18.8 QOSC4A- CREDIT_C7_G2 * CPU Address:h561 Bits [5:0]: Bits [7:6]: * * W7 - Credit register. (Default 5'h10) Reserved QOSC43 through QOSC4Arepresents the set of WFQ parameters (see section 7.5) for Gigabit port 2. The granularity of the numbers is 1, and their sum must be 64. QOSC43 corresponds to W0, and QOSC4A corresponds to W7. 11.9.19 Classes WFQ Credit Port G3 * Access by CPU only 11.9.19.1 QOSC4B - CREDIT_C0_G3 * CPU Address:h562 Bits [5:0]: Bits [7:6]: * * * W0 - Credit register for WFQ. (Default 6'h04) Priority type. Define one of the four QoS mode of operation for port 3 (Default 2'00) See table below: Queue Option 1 Bit [7:6] = 2'B00 Option 2 Bit [7:6] = 2'B01 Option 3 Bit [7:6] = 2'B10 Option 4 Bit [7:6] = 2'B11 Credit for WFQ - Bit [5:0] P7 P6 P5 P4 P3 P2 P1 BE BE P0 DELAY BOUND SP SP WFQ W7 W6 W5 W4 W3 W2 DELAY BOUND WFQ W1 W0 100 Zarlink Semiconductor Inc. Data Sheet 11.9.19.2 QOSC4 - CREDIT_C1_G3 * CPU Address:h563 Bits [7]: * Flow control allow during WFQ scheme. (Default 1'b1) * 0 = Not support QoS when the Source port Flow control status is on. * 1= Always support QoS) MVTX2804 Bits [6]: * Flow control BE Queue only. (Default 1'b1) * 0= DO NOT send any frames if the XOFF is on. * 1= the P7-P2 frames can be sent even the XOFF is ON Bits [5:0] * W1 - Credit register. (Default 4'h04) Fc_allow Fc_be_only Lost_ok Ingressfor src fc status 0 1 0 1 0 1 Go to BE Queue if (Src FC or Des FC on) otherwise Normal Go to BE Queue if (Dest FC on) otherwise Normal (WFQ only) Go to BE Queue if (Src FC on) otherwise BAD (WFQ only) Always Normal Go to BE Queue if (Src FC on) Always Normal Egress- for dest fc_status 0 0 1 1 X X 0 0 0 0 1 1 11.9.19.3 QOSC4D - CREDIT_C2_G3 * CPU Address:h564 Bits [5:0]: Bits [7:6]: * * W2 - Credit register. (Default 4'h04) Reserved 11.9.19.4 QOSC4E - CREDIT_C3_G3 * CPU Address:h565 Bits [5:0]: Bits [7:6]: * * W3 - Credit register. (Default 4'h04) Reserved 11.9.19.5 QOSC4F - CREDIT_C4_G3 * CPU Address:h566 Bits [5:0]: Bits [7:6]: * * W4 - Credit register. (Default 4'h04) Reserved Zarlink Semiconductor Inc. 101 MVTX2804 11.9.19.6 QOSC50 - CREDIT_C5_G3 * CPU Address:h567 Bits [5:0]: Bits [7:6]: * * W5 - Credit register. (Default 5'h8) Reserved Data Sheet 11.9.19.7 QOSC51- CREDIT_C6_G3 * CPU Address:h568 Bits [5:0]: Bits [7:6]: * * W6 - Credit register. (Default 5'h8) Reserved 11.9.19.8 QOSC52- CREDIT_C7_G3 * CPU Address:h569 Bits [5:0]: Bits [7:6]: * * W7 - Credit register. (Default 5'h10) Reserved QOSC4B through QOSC52 represents the set of WFQ parameters (see section 7.5) for Gigabit port 3. The granularity of the numbers is 1, and their sum must be 64. QOSC4B corresponds to W0, and QOSC52 corresponds to W7. 11.9.20 Classes WFQ Credit Port G4 * Access by CPU only 11.9.20.1 QOSC53 - CREDIT_C0_G4 * CPU Address:h56A Bits [5:0]: Bits [7:6]: * * * W0 - Credit register for WFQ. (Default 6'h04) Priority type. Define one of the four QoS mode of operation for port 4 (Default 2'00) See table below: Queue Option 1 Bit [7:6] = 2'B00 Option 2 Bit [7:6] = 2'B01 Option 3 Bit [7:6] = 2'B10 Option 4 Bit [7:6] = 2'B11 Credit for WFQ - Bit [5:0] P7 P6 P5 P4 P3 P2 P1 BE BE P0 DELAY BOUND SP SP WFQ W7 W6 W5 W4 W3 W2 DELAY BOUND WFQ W1 W0 102 Zarlink Semiconductor Inc. Data Sheet 11.9.20.2 QOSC54 - CREDIT_C1_G4 * CPU Address:h56B Bits [7]: * Flow control allow during WFQ scheme. (Default 1'b1) * 0 = Not support QoS when the Source port Flow control status is on. * 1= Always support QoS) MVTX2804 Bits [6]: * Flow control BE Queue only. (Default 1'b1) * 0= DO NOT send any frames if the XOFF is on. * 1= the P7-P2 frames can be sent even the XOFF is ON Bits [5:0] * W1 -Credit register. (Default 4'h04) Fc_allow Fc_be_only Lost_ok Ingress- for src fc status 0 1 0 1 0 1 Go to BE Queue if (Src FC or Des FC on) otherwise Normal Go to BE Queue if (Dest FC on) otherwise Normal (WFQ only) Go to BE Queue if (Src FC on) otherwise BAD (WFQ only) Always Normal Go to BE Queue if (Src FC on) Always Normal Egress- for dest fc_status 0 0 1 1 X X 0 0 0 0 1 1 11.9.20.3 QOSC55 - CREDIT_C2_G4 * CPU Address:h56C Bits [5:0]: Bits [7:6]: * * W2 - Credit register. (Default 4'h04) Reserved 11.9.20.4 QOSC56 - CREDIT_C3_G4 * CPU Address:h56D Bits [5:0]: Bits [7:6]: * * W3 - Credit register. (Default 4'h04) Reserved 11.9.20.5 QOSC57 - CREDIT_C4_G4 * CPU Address:h56E Bits [5:0]: Bits [7:6]: * * W4 - Credit register. (Default 4'h04) Reserved Zarlink Semiconductor Inc. 103 MVTX2804 11.9.20.6 QOSC58 - CREDIT_C5_G4 * CPU Address:h56F Bits [5:0]: Bits [7:6]: * * W5 - Credit register. (Default 5'h8) Reserved Data Sheet 11.9.20.7 QOSC59- CREDIT_C6_G4 * CPU Address:h570 Bits [5:0]: Bits [7:6]: * * W6 - Credit register. (Default 5'h8) Reserved 11.9.20.8 QOSC5A- CREDIT_C7_G4 * CPU Address:h571 Bits [5:0]: Bits [7:6]: * * W7 - Credit register. (Default 5'h10) Reserved QOSC53 through QOSC5A represents the set of WFQ parameters (see section 7.5) for Gigabit port 4. The granularity of the numbers is 1, and their sum must be 64. QOSC53 corresponds to W0, and QOSC5A corresponds to W7. 11.9.21 Classes WFQ Credit Port G5 * Access by CPU only 11.9.21.1 QOSC5B - CREDIT_C0_G5 * CPU Address:h572 Bits [5:0]: Bits [7:6]: * * * W0 - Credit register for WFQ. (Default 6'h04) Priority type. Define one of the four QoS mode of operation for port 5 (Default 2'00) See table below: Queue Option 1 Bit [7:6] = 2'B00 Option 2 Bit [7:6] = 2'B01 Option 3 Bit [7:6] = 2'B10 Option 4 Bit [7:6] = 2'B11 Credit for WFQ - Bit [5:0] P7 P6 P5 P4 P3 P2 P1 BE BE P0 DELAY BOUND SP SP WFQ W7 W6 W5 W4 W3 W2 DELAY BOUND WFQ W1 W0 104 Zarlink Semiconductor Inc. Data Sheet 11.9.21.2 QOSC5C - CREDIT_C1_G5 * CPU Address:h573 Bits [7]: * Flow control allow during WFQ scheme. (Default 1'b1) * 0 = Not support QoS when the Source port Flow control status is on. * 1= Always support QoS) MVTX2804 Bits [6]: * Flow control BE Queue only. (Default 1'b1) * 0= DO NOT send any frames if the XOFF is on. * 1= the P7-P2 frames can be sent even the XOFF is ON Bits [5:0] * W1 - Credit register. (Default 4'h04) Fc_allow Fc_be_only Lost_ok Ingress- for src fc status 0 1 0 1 0 1 Go to BE Queue if (Src FC or Des FC on) otherwise Normal Go to BE Queue if (Dest FC on) otherwise Normal (WFQ only) Go to BE Queue if (Src FC on) otherwise BAD (WFQ only) Always Normal Go to BE Queue if (Src FC on) Always Normal Egress- for dest fc_status 0 0 1 1 X X 0 0 0 0 1 1 11.9.21.3 QOSC5D - CREDIT_C2_G5 * CPU Address:h574 Bits [5:0]: Bits [7:6]: * * W2 - Credit register. (Default 4'h04) Reserved 11.9.21.4 QOSC5E - CREDIT_C3_G5 * CPU Address:h575 Bits [5:0]: Bits [7:6]: * * W3 - Credit register. (Default 4'h04) Reserved 11.9.21.5 QOSC5F - CREDIT_C4_G5 * CPU Address:h576 Bits [5:0]: Bits [7:6]: * * W4 - Credit register. (Default 4'h04) Reserved Zarlink Semiconductor Inc. 105 MVTX2804 11.9.21.6 QOSC60 - CREDIT_C5_G5 * CPU Address:h577 Bits [5:0]: Bits [7:6]: * * W5 - Credit register. (Default 5'h8) Reserved Data Sheet 11.9.21.7 QOSC61- CREDIT_C6_G5 * CPU Address:h578 Bits [5:0]: Bits [7:6]: * * W6 - Credit register. (Default 5'h8) Reserved 11.9.21.8 QOSC62- CREDIT_C7_G5 * CPU Address:h579 Bits [5:0]: Bits [7:6]: * * W7 - Credit register. (Default 5'h10) Reserved QOSC5B through QOSC62 represents the set of WFQ parameters (see section 7.5) for Gigabit port 5. The granularity of the numbers is 1, and their sum must be 64. QOSC5B corresponds to W0, and QOSC62 corresponds to W7. 11.9.22 Classes WFQ Credit Port G6 * Access by CPU only 11.9.22.1 QOSC63 - CREDIT_C0_G6 * CPU Address:h57A Bits [5:0]: Bits [7:6]: * * * W0 - Credit register for WFQ. (Default 6'h04) Priority type. Define one of the four QoS mode of operation for port 6 (Default 2'00) See table below: Queue Option 1 Bit [7:6] = 2'B00 Option 2 Bit [7:6] = 2'B01 Option 3 Bit [7:6] = 2'B10 Option 4 Bit [7:6] = 2'B11 Credit for WFQ - Bit [5:0] P7 P6 P5 P4 P3 P2 P1 BE BE P0 DELAY BOUND SP SP WFQ W7 W6 W5 W4 W3 W2 DELAY BOUND WFQ W1 W0 106 Zarlink Semiconductor Inc. Data Sheet 11.9.22.2 QOSC64 - CREDIT_C1_G6 * CPU Address:h57B Bits [7]: * Flow control allow during WFQ scheme. (Default 1'b1) * 0 = Not support QoS when the Source port Flow control status is on. * 1= Always support QoS) MVTX2804 Bits [6]: * Flow control BE Queue only. (Default 1'b1) * 0= DO NOT send any frames if the XOFF is on. * 1= the P7-P2 frames can be sent even the XOFF is ON Bits [5:0] * W1 - Credit register. (Default 4'h04) Fc_allow Fc_be_only Lost_ok Ingressfor src fc status 0 1 0 1 0 1 Go to BE Queue if (Src FC or Des FC on) otherwise Normal Go to BE Queue if (Dest FC on) otherwise Normal (WFQ only) Go to BE Queue if (Src FC on) otherwise BAD (WFQ only) Always Normal Go to BE Queue if (Src FC on) Always Normal Egress- for dest fc_status 0 0 1 1 X X 0 0 0 0 1 1 11.9.22.3 QOSC65 - CREDIT_C2_G6 * CPU Address:h57C Bits [5:0]: Bits [7:6]: * * W2 - Credit register. (Default 4'h04) Reserved 11.9.22.4 QOSC66 - CREDIT_C3_G6 * CPU Address:h57D Bits [5:0]: Bits [7:6]: * * W3 - Credit register. (Default 4'h04) Reserved 11.9.22.5 QOSC67 - CREDIT_C4_G6 * CPU Address:h57E Bits [5:0]: Bits [7:6]: * * W4 - Credit register. (Default 4'h04) Reserved Zarlink Semiconductor Inc. 107 MVTX2804 11.9.22.6 QOSC68 - CREDIT_C5_G6 * CPU Address:h57F Bits [5:0]: Bits [7:6]: * * W5 - Credit register. (Default 5'h8) Reserved Data Sheet 11.9.22.7 QOSC69- CREDIT_C6_G6 * CPU Address:h580 Bits [5:0]: Bits [7:6]: * * W6 - Credit register. (Default 5'h8) Reserved 11.9.22.8 QOSC6A- CREDIT_C7_G6 * CPU Address:h581 Bits [5:0]: Bits [7:6]: * * W7 - Credit register. (Default 5'h10) Reserved QOSC63 through QOSC6A represents the set of WFQ parameters (see section 7.5) for Gigabit port 6. The granularity of the numbers is 1, and their sum must be 64. QOSC63 corresponds to W0, and QOSC6A corresponds to W7. 11.9.23 Classes WFQ Credit Port G7 * Access by CPU only 11.9.23.1 QOSC6B - CREDIT_C0_G7 * CPU Address:h582 Bits [5:0]: Bits [7:6]: * * * W0 - Credit register for WFQ. (Default 6'h04) Priority type. Define one of the four QoS mode of operation for port 7 (Default 2'00) See table below: Queue Option 1 Bit [7:6] = 2'B00 Option 2 Bit [7:6] = 2'B01 Option 3 Bit [7:6] = 2'B10 Option 4 Bit [7:6] = 2'B11 Credit for WFQ - Bit [5:0] P7 P6 P5 P4 P3 P2 P1 BE BE P0 DELAY BOUND SP SP WFQ W7 W6 W5 W4 W3 W2 DELAY BOUND WFQ W1 W0 108 Zarlink Semiconductor Inc. Data Sheet 11.9.23.2 QOSC6C - CREDIT_C1_G7 * CPU Address:h583 Bits [7]: * Flow control allow during WFQ scheme. (Default 1'b1) * 0 = Not support QoS when the Source port Flow control status is on. * 1= Always support QoS) MVTX2804 Bits [6]: * Flow control BE Queue only. (Default 1'b1) * 0= DO NOT send any frames if the XOFF is on. * 1= the P7-P2 frames can be sent even the XOFF is ON Bits [5:0] * W1 - Credit register. (Default 4'h04) Fc_allow Fc_be_only Lost_ok Ingress- for src fc status 0 1 0 1 0 1 Go to BE Queue if (Src FC or Des FC on) otherwise Normal Go to BE Queue if (Dest FC on) otherwise Normal (WFQ only) Go to BE Queue if (Src FC on) otherwise BAD (WFQ only) Always Normal Go to BE Queue if (Src FC on) Always Normal Egress- for dest fc_status 0 0 1 1 X X 0 0 0 0 1 1 11.9.23.3 QOSC6D - CREDIT_C2_G7 * CPU Address:h584 Bits [5:0]: Bits [7:6]: * * W2 - Credit register. (Default 4'h04) Reserved 11.9.23.4 QOSC6E - CREDIT_C3_G7 * CPU Address:h585 Bits [5:0]: Bits [7:6]: * * W3 - Credit register. (Default 4'h04) Reserved Zarlink Semiconductor Inc. 109 MVTX2804 11.9.23.5 QOSC6F - CREDIT_C4_G7 * CPU Address:h586 Bits [5:0]: Bits [7:6]: * * W4 - Credit register. (Default 4'h04) Reserved Data Sheet 11.9.23.6 QOSC70 - CREDIT_C5_G7 * CPU Address:h587 Bits [5:0]: Bits [7:6]: * * W5 - Credit register. (Default 5'h8) Reserved 11.9.23.7 QOSC71- CREDIT_C6_G7 * CPU Address:h588 Bits [5:0]: Bits [7:6]: * * W6 - Credit register. (Default 5'h8) Reserved 11.9.23.8 QOSC72- CREDIT_C7_G7 * CPU Address:h589 Bits [5:0]: Bits [7:6]: * * W7 - Credit register. (Default 5'h10) Reserved QOSC6B through QOSC72 represents the set of WFQ parameters (see section 7.5) for Gigabit port 7. The granularity of the numbers is 1, and their sum must be 64. QOSC6B corresponds to W0, and QOSC72 corresponds to W7. 11.9.24 Class 6 Shaper Control Port G0 * Accessed by CPU only 11.9.24.1 QOSC73 - TOKEN_RATE_G0 * CPU Address:h58A Bits [7:0]: * Bytes allow to transmit every frame time (0.512usec) when regulated by Shaper logic. (Default: 8'h08) 11.9.24.2 QOSC74 - TOKEN_LIMIT_G0 * CPU Address:h58B Bits [7:0]: * Bytes allow to continue transmit out when regulated by Shaper logic. (16byte/unit) (Default: 8'hC0) QOSC73 and QOSC74 correspond to parameters from section 7.6 on the shaper for EF traffic. QOSC73 is an integer less than 64 (average rate), with granularity 1. QOSC74 is the programmed maximum value of the counter (maximum burst size). This value is expressed in multiples of 16. QOSC73 and QOSC74 apply to Gigabit port 0. Register QOSC39-CREDIT_C6_G0 programs the peak rate. See QoS application note for more information. 110 Zarlink Semiconductor Inc. Data Sheet 11.9.25 Class 6 Shaper Control Port G1 * Accessed by CPU only MVTX2804 11.9.25.1 QOSC75 - TOKEN_RATE_G1 * CPU Address:h58C Bits [7:0]: * Bytes allow to transmit every frame time (0.512usec) when regulated by Shaper logic. (Default: 8'h08) 11.9.25.2 QOSC76 - TOKEN_LIMIT_G1 * CPU Address:h58D Bits [7:0]: * Bytes allow to continue transmit out when regulated by Shaper logic. (16byte/unit) (Default: 8'hC0) QOSC75 and QOSC76 correspond to parameters from section 7.6 on the shaper for EF traffic. QOSC75 is an integer less than 64 (average rate), with granularity 1. QOSC76 is the programmed maximum value of the counter (maximum burst size). This value is expressed in multiples of 16. QOSC75 and QOSC76 apply to Gigabit port 0. Register QOSC41-CREDIT_C6_G1 programs the peak rate. See QoS application note for more information. 11.9.26 Class 6 Shaper Control Port G2 * Accessed by CPU only 11.9.26.1 QOSC77 - TOKEN_RATE_G2 * CPU Address:h58E Bits [7:0]: * Bytes allow to transmit every frame time (0.512usec) when regulated by Shaper logic. (Default: 8'h08) 11.9.26.2 QOSC78 - TOKEN_LIMIT_G2 * CPU Address:h58F Bits [7:0]: * Bytes allow to continue transmit out when regulated by Shaper logic. (16byte/unit) (Default: 8'hC0) QOSC77 and QOSC78 correspond to parameters from section 7.6 on the shaper for EF traffic. QOSC77 is an integer less than 64 (average rate), with granularity 1. QOSC78 is the programmed maximum value of the counter (maximum burst size). This value is expressed in multiples of 16. QOSC77 and QOSC78 apply to Gigabit port 2. QOSC49-CREDIT_C6_G2 programs the peak rate. See QoS application note for more information. 11.9.27 Class 6 Shaper Control Port G3 * Accessed by CPU only 11.9.27.1 QOSC79 - TOKEN_RATE_G3 * CPU Address:h590 Bits [7:0]: * Bytes allow to transmit every frame time (0.512usec) when regulated by Shaper logic. (Default: 8'h08) Zarlink Semiconductor Inc. 111 MVTX2804 11.9.27.2 QOSC7A - TOKEN_LIMIT_G3 * CPU Address:h591 Bits [7:0]: * Bytes allow to continue transmit out when regulated by Shaper logic. (16byte/unit) (Default: 8'hC0) Data Sheet QOSC79 and QOSC7A correspond to parameters from section 7.6 on the shaper for EF traffic. QOSC79 is an integer less than 64 (average rate), with granularity 1. QOSC7A is the programmed maximum value of the counter (maximum burst size). This value is expressed in multiples of 16. QOSC79 and QOSC7A apply to Gigabit port 3. QOSC51-CREDIT_C6_G3 programs the peak rate. See QoS application note for more information. 11.9.28 Class 6 Shaper Control Port G4 * Accessed by CPU only 11.9.28.1 QOSC7B - TOKEN_RATE_G4 * CPU Address:h592 Bits [7:0]: * Bytes allow to transmit every frame time (0.512usec) when regulated by Shaper logic. (Default: 8'h08) 11.9.28.2 QOSC7C - TOKEN_LIMIT_G4 * CPU Address:h593 Bits [7:0]: * Bytes allow to continue transmit out when regulated by Shaper logic. (16byte/unit) (Default: 8'hC0) QOSC7B and QOSC7C correspond to parameters from section 7.6 on the shaper for EF traffic. QOSC7B is an integer less than 64, with granularity 1 (average rate). QOSC7C is the programmed maximum value of the counter (maximum burst size). This value is expressed in multiples of 16. QOSC7B and QOSC7C apply to Gigabit port 4. QOSC59-CREDIT_C6_G4 programs the peak rate. See QoS application note for more information. 11.9.29 Class 6 Shaper Control Port G5 * Accessed by CPU only 11.9.29.1 QOSC7D - TOKEN_RATE_G5 * CPU Address:h594 Bits [7:0]: * Bytes allow to transmit every frame time (0.512usec) when regulated by Shaper logic. (Default: 8'h08) 11.9.29.2 QOSC7E - TOKEN_LIMIT_G5 * CPU Address:h595 Bits [7:0]: * Bytes allow to continue transmit out when regulated by Shaper logic. (16byte/unit) (Default: 8'hC0) QOSC7D and QOSC7E correspond to parameters from section 7.6 on the shaper for EF traffic. QOSC7D is an integer less than 64 (average rate), with granularity 1. QOSC7E is the programmed maximum value of the counter C1 (maximum burst size). This value is expressed in multiples of 16. QOSC7D and QOSC7E apply to Gigabit port 5. QOSC60-CREDIT_C6_G5 programs the peak rate. See QoS application note for more information. 112 Zarlink Semiconductor Inc. Data Sheet 11.9.30 Class 6 Shaper Control Port G6 * Accessed by CPU only MVTX2804 11.9.30.1 QOSC7F - TOKEN_RATE_G6 * CPU Address:h596 Bits [7:0]: * Bytes allow to transmit every frame time (0.512usec) when regulated by Shaper logic. (Default: 8'h08) 11.9.30.2 QOSC80 - TOKEN_LIMIT_G6 * CPU Address:h597 Bits [7:0]: * Bytes allow to continue transmit out when regulated by Shaper logic. (16byte/unit) (Default: 8'hC0) QOSC7F and QOSC80 correspond to parameters from section 7.6 on the shaper for EF traffic. QOSC7F is an integer less than 64 (average rate), with granularity 1. QOSC80 is the programmed maximum value of the counter C1 (maximum burst size). This value is expressed in multiples of 16. QOSC7F and QOSC80 apply to Gigabit port 6. QOSC69-CREDIT_C6_G6 programs the peak rate. See QoS application note for more information. 11.9.31 Class 6 Shaper Control Port G7 * Accessed by CPU only 11.9.31.1 QOSC81 - TOKEN_RATE_G7 * CPU Address:h598 Bits [7:0]: * Bytes allow to transmit every frame time (0.512usec) when regulated by Shaper logic. (Default: 8'h08) 11.9.31.2 QOSC82 - TOKEN_LIMIT_G7 * CPU Address:h599 Bits [7:0]: * Bytes allow to continue transmit out when regulated by Shaper logic. (16byte/unit) (Default: 8'hC0) QOSC81 and QOSC82 correspond to parameters from section 7.6 on the shaper for EF traffic. QOSC81 is an integer less than 64 (average rate), with granularity 1. QOSC82 is the programmed maximum value of the counter C1 (maximum burst size). This value is expressed in multiples of 16. QOSC81 and QOSC82 apply to Gigabit port 7. QOSC6F-CREDIT_C6_G7 programs the peak rate. See QoS application note for more information. 11.9.32 RDRC0 - WRED Rate Control 0 * * I2C Address:h085, CPU Address:h59A Accessed by CPU, Serial Interface and I2C (R/W) 7 X Rate 43 Y Rate 0 Zarlink Semiconductor Inc. 113 MVTX2804 Bits [7:4]: Bits[3:0]: * * Corresponds to the percentage X% in Chapter 7. Used for random early drop. Granularity 6.25%. (Default: 4'h8) Corresponds to the percentage Y% in Chapter 7. Used for random early drop. Granularity 6.25%.(Default: 4'hE) Data Sheet 114 Zarlink Semiconductor Inc. Data Sheet 11.9.33 RDRC1 - WRED Rate Control 1 * * I2C Address:h086, CPU Address:h59B Accessed by CPU, Serial Interface and I2C (R/W) 7 Z Rate 43 B Rate 0 MVTX2804 Bits [7:4]: Bits[3:0]: * * Corresponds to the percentage Z% in Chapter 7. Used for random early drop. Granularity 6.25%.%. (Default: 4'h6) Corresponds to the best effort frame drop percentage B%, when shared pool is all in use and destination port best effort queue reaches UCC. Used for random early drop. Granularity 6.25%.%. (Default: 4'h8) 11.10 Group 6 Address 11.10.1 MISC Group 11.10.1.1 MII_OP0 - MII REGISTER OPTION 0 * * I2C Address:h0B1, CPU Address:h600 Accessed by CPU, serial interface and I2C (R/W) 7 Hfc Bit [7]: 6 1prst 5 NP 4 Vendor Spc. Reg Addr 0 * Half duplex flow control (Do not use half duplex mode) 0 = Half duplex flow control always enable 1 = Half duplex flow control by negotiation Bit[6]: Bit [5] * Link partner reset auto-negotiate disable * Next page enable 1: enable 0: disable Bit[4:0]: * Vendor specified link status register address (null value means don't use it) (Default 00) 11.10.1.2 MII_OP1 - MII REGISTER OPTION 1 * * I2C Address:0B2, CPU Address:h601 Accessed by CPU, serial interface and I2C (R/W) 7 Speed bit location Bits[3:0]: Bits [7:4]: * * 4 3 Duplex bit location 0 Duplex bit location in vendor specified register Speed bit location in vendor specified register (Default 00) Zarlink Semiconductor Inc. 115 MVTX2804 11.10.1.3 FEN - FEATURE REGISTER * * I2C Address:h0B3, CPU Address:h602 Accessed by CPU, serial interface and I2C (R/W) 7 DML Bits [0]: * 6 MII 5 Rp 4 IP Mul 3 V-Sp 2 DS 1 0 SC Data Sheet Statistic Counter Enable (Default 0) * 0 - Disable * 1 - Enable * When statistic counter is enable, an interrupt control frame is generated to the CPU, every time a counter wraps around. This feature requires an external CPU. Reserved Support DS EF Code. (Default 0) * 0 - Disable * 1 - Enable (all ports) Bits[1]: Bit [2]: * * * Bit [3]: * When 101110 is detected in DS field (TOS[7:2]), the frame priority is set for 110 and drop is set for 0. Enable VLAN spanning tree support (Default 0) * 0 - Disable * 1 - Enable * When VLAN spanning tree is enable the register ECR1Pn are not used to program the port spanning tree status. The port spanning tree status is programmed in the VLAN status field. Disable IP Multicast Support (Default 1) * 0 - Enable IP Multicast Support * 1 - Disable IP Multicast Support Bit [4]: * * When enable, IGMP packets are identified by search engine and are passed to the CPU for processing. IP multicast packets are forwarded to the IP multicast group members according to the VLAN port mapping table. Enable report of new MAC and VLAN (Default 0) * 0 - Disable report to CPU * 1 - Enable report to CPU Bit [5]: * * When disable: new VLAN port association report, new MAC address report and aging report are disable for all ports. When enable, register SE_OPEMODE is used to enable/disable selectively each function. 0: Enable MII Management State Machine (Default 0) 1: Disable MII Management State Machine 0: Enable using MCT Link List structure 1: Disable using MCT Link List structure Bit [6]: Bit [7]: * * * * 11.10.1.4 MIIC0 - MII COMMAND REGISTER 0 * * * CPU Address:h603 Accessed by CPU and serial interface only (R/W) Bit [7:0] MII Data [7:0] 116 Zarlink Semiconductor Inc. Data Sheet MVTX2804 Note: Before programming MII command: set FEN[6], check MIIC3, making sure no RDY, and no VALID; then program MII command. 11.10.1.5 MIIC1 - MII COMMAND REGISTER 1 * CPU Address:h604 * Accessed by CPU and serial interface only (R/W) * Bit [7:0] MII Data [15:8] Note: Before programming MII command: set FEN[6], check MIIC3, making sure no RDY and no VALID; then program MII command. 11.10.1.6 MIIC2 - MII COMMAND REGISTER 2 * * CPU Address:h605 Accessed by CPU and serial interface only (R/W) 7 6 MII OP Bits [4:0]: Bit [6:5] 5 4 Register address 0 REG_AD - Register PHY Address OP - Operation code "10" for read command and "01" for write command Note: Before programming MII command: set FEN[6], check MIIC3, making sure no RDY and no VALID; then program MII command. 11.10.1.7 MIIC3 - MII COMMAND REGISTER 3 * * CPU Address:h606 Accessed by CPU and serial interface only (R/W) 7 Rdy Bits [4:0]: Bit [6] Bit [7] 6 Valid 5 4 PHY address 0 PHY_AD - 5 Bit PHY Address VALID - Data Valid from PHY (Read Only) RDY - Data is returned from PHY (Ready Only) Note: Before programming MII command: set FEN[6], check MIIC3, making sure no RDY and no VALID; then program MII command. 11.10.1.8 MIID0 - MII DATA REGISTER 0 * * * CPU Address:h607 Accessed by CPU and serial interface only (RO) Bit [7:0] MII Data [7:0] 11.10.1.9 MIID1 - MII DATA REGISTER 0 * * * CPU Address:h608 Accessed by CPU and serial interface only (RO) Bit [7:0] MII Data [15:8] Zarlink Semiconductor Inc. 117 MVTX2804 11.10.1.10LED MODE - LED CONTROL * * I2C Address:h0B4; CPU Address:h609 Accessed by CPU, serial interface and I2C (R/W) 7 lpbk Bit[1:0] 6 5 Out Pattern 4 3 2 Clock rate 1 0 Data Sheet Hold Time * Sample hold time(Default 2'b00) 2'b00- 8 msec 2'b01- 16 msec 2'b10- 32 msec 2'b11- 64 msec Bit[3:2] * LED clock speed (serial mode) (Default 2'b10) 2'b00- sclk/1282'b01- sclk/256 2'b10- sclk/10242'b11- sclk/2048 * LED clock speed (parallel mode) (Default 2'b10) 2'b00- sclk/10242'b01- sclk/4096 2'b10- sclk/20482'b11- sclk/8192 Bit[5:4] LED indicator out pattern (Default 2'b11) 2'b00- Normal output, LED signals go straight out, no logical combination 2'b01- 4 bi-color LED mode 2'b10- 3 bi-color LED mode 2'b11- programmable mode 1. Normal mode: LED_BYTEOUT_[7]:Collision (COL) LED_BYTEOUT_[6]:Full duplex (FDX) LED_BYTEOUT_[5]:Speed[1] (SP1) LED_BYTEOUT_[4]:Speed[0] (SP0) LED_BYTEOUT_[3]:Link (LNK) LED_BYTEOUT_[2]:Rx (RXD) LED_BYTEOUT_[1]:Tx (TXD) LED_BYTEOUT_[0]:Flow Control (FC) 118 Zarlink Semiconductor Inc. Data Sheet 2. 4 bi-color LED mode LED_BYTEOUT_[7]:COL LED_BYTEOUT_[6]:1000FDX LED_BYTEOUT_[5]:1000HDX LED_BYTEOUT_[4]:100FDX LED_BYTEOUT_[3]:100HDX LED_BYTEOUT_[2]:10FDX LED_BYTEOUT_[1]:10HDX LED_BYTEOUT_[0]:ACT Note: All output qualified by Link signal 3. 3 bi-color LED mode: LED_BYTEOUT_[7]:COL LED_BYTEOUT_[6]:LNK LED_BYTEOUT_[5]:FC LED_BYTEOUT_[4]:SPD1000 LED_BYTEOUT_[3]:SPD100 LED_BYTEOUT_[2]:FDX LED_BYTEOUT_[1]:HDX LED_BYTEOUT_[0]:ACT Note: All output qualified by Link signal 4. Programmable mode: LED_BYTEOUT_[7]:Link LED_BYTEOUT_[6:0]:Defined by the LEDSIG6 ~ LEDSIG0 programmable registers. Note: All output qualified by Link signal Bit[6]: Bit[7]: * * Reserved. Must be '0' MVTX2804 Enable internal loop back. When this bit is set to '1' all ports work in internal loop back mode. For normal operation must be '0'. 11.10.2 CHECKSUM - EEPROM Checksum * * I2C Address h0C5, CPU Address:h60B Accessed by CPU, serial interface and I2C (R/W) Bit[7:0]: (Default 00) Zarlink Semiconductor Inc. 119 MVTX2804 11.10.3 LED User 11.10.3.1 LEDUSER0 * * I2C Address h0BB, CPU Address:h60C Accessed by CPU, serial interface and I2C (R/W) 7 LED USER0 Bit[7:0]: (Default 00) Content will send out by LED serial logic 0 Data Sheet 11.10.3.2 LEDUSER1 * * I2C Address h0BC, CPU Address:h60D Accessed by CPU, serial interface and I2C (R/W) 7 LED USER1 Bit[7:0]: (Default 00) Content will send out by LED serial logic 0 11.10.3.3 LEDUSER2/LEDSIG2 * I2C Address h0BD, CPU Address:h60E * Accessed by CPU, serial interface and I2C (R/W) In serial mode: 7 LED USER2 Bit[7:0]: (Default 00) Content will be sent out by LED serial shift logic In parallel mode: this register is used for programming the LED pin - led_byteout_[2] 7 COL Bit [3:0]: FDX SP1 4 SP0 3 COL FDX SP1 0 SP0 0 (Default 4'H0) Signal polarity: 0: not invert polarity (high true) 1: invert polarity Bit [7:4] (Default 4'H8) Signal Select: 0: not select 1: select the corresponding bit When bits get selected, the led_byteout_[2] = AND (all selected bits) 120 Zarlink Semiconductor Inc. Data Sheet 11.10.3.4 LEDUSER3/LEDSIG3 * I2C Address:h0BE, CPU Address:h60F * Access by CPU, serial interface (R/W) In serial mode: 7 LED USER3 Bit [7:0]: (Default 8'H33) Content will be sent out by LED serial shift logic. 0 MVTX2804 In parallel mode: this register is used for programming the LED pin - led_byteout_[3] 7 COL Bit [3:0]: FDX SP1 SP0 COL FDX SP1 0 SP0 (Default 4'H3) Signal polarity: 0: not invert polarity (high true) 1: invert polarity Bit [7:4] (Default 4'H3) Signal Select: 0: not select 1: select the corresponding bit When bits get selected, the led_byteout_[3] = AND (all selected bits) 11.10.3.5 LEDUSER4/LEDSIG4 * * I2C Address:h0BF, CPU Address:h610 Access by CPU, serial interface (R/W) 7 LED USER4 Bit [7:0] (Default 8'H32) Content will be sent out by LED serial shift logic. In parallel mode: this register is used for programming the LED pin - led_byteout_[4] 7 COL Bit [3:0]: FDX SP1 4 SP0 3 COL FDX SP1 0 SP0 0 (Default 4'H2) Signal polarity: 0: not invert polarity (high true) 1: invert polarity Zarlink Semiconductor Inc. 121 MVTX2804 Bit [7:4] (Default 4'H3) Signal Select: 0: not select 1: select the corresponding bit When bits get selected, the led_byteout_[4] = AND (all selected bits) Data Sheet 11.10.3.6 LEDUSER5/LEDSIG5 * * I2C Address:h0C0, CPU Address:h611 Access by CPU, serial interface (R/W) 7 LED USER5 Bit [7:0] (Default 8'H20) Content will be sent out by LED serial shift logic. 0 In parallel mode: this register is used for programming the LED pin - led_byteout_[5] 7 COL Bit [3:0] FDX SP1 4 SP0 3 COL FDX SP1 0 SP0 (Default 4'H0) Signal polarity: 0: not invert polarity (high true) 1: invert polarity Bit [7:4] (Default 4'H2) Signal Select: 0: not select 1: select the corresponding bit When bits get selected, the led_byteout_[5] = AND (all selected bits) 11.10.3.7 LEDUSER6/LEDSIG6 * * I2C Address:h0C1, CPU Address:h612 Access by CPU, serial interface (R/W) 7 LED USER6 Bit [7:0] (Default 8'H40) Content will be sent out by LED serial shift logic. In parallel mode: this register is used for programming the LED pin - led_byteout_[6] 7 COL FDX SP1 4 SP0 3 COL FDX SP1 0 SP0 0 122 Zarlink Semiconductor Inc. Data Sheet Bit [3:0] (Default 4'B0000) Signal polarity: 0: not invert polarity (high true) 1: invert polarity Bit [7:4] (Default 4'b0100) Signal Select: 0: not select 1: select the corresponding bit When bits get selected, the led_byteout_[6] = AND (all selected bits), or the polarity of led_byteout_[6] is controlled by LEDSIG1_0[3] MVTX2804 11.10.3.8 LEDUSER7/LEDSIG1_0 * * I2C Address:h0C2, CPU Address:h613 Access by CPU, serial interface (R/W) 7 LED USER7 Bit [7:0] (Default 8'H61) Content will be sent out by LED serial shift logic. In parallel mode: this register is used for programming the LED pin - led_byteout_[2] 7 GP Bit [7] RX TX 4 FC 3 P6 RX TX 0 FC 0 (Default 1'B0) * Global output polarity: this bit controls the output polarity of all led_byteout_ and led_port_sel pins. 0: no invert polarity - (led_byteout_[7:0] are high activated, led_port_sel[9:0] are low activated) 1: invert polarity - (led_byteout_[7:0] are low activated, led_port_sel[9:0] are high activated) Bit [6:4] (Default 3'B110) Signal Select: 0: not select 1: select the corresponding bit When bits get selected, the led_byteout_[6] = OR (all selected bits) Bit[3] (Default 1'B0) Polarity control of led_byteout_[6] 0: not invert 1: invert Zarlink Semiconductor Inc. 123 MVTX2804 Bit [2:0] (Default 3'b001) Signal Select: 0: not select 1: select the corresponding bit When bits get selected, the led_byteout_[0] = OR (all selected bits) Data Sheet 11.10.4 MIINP0 - MII Next Page Data Register 0 * * I2C Address:h0C3, CPU Address:h614 Access by CPU and serial interface only (R/W) Bit [7:0] MII next page Data [7:0] 11.10.5 MIINP1 - MII Next Page Data Register 1 * I2C Address:h0C4, CPU Address:h615 Access by CPU and serial interface only (R/W) Bit [7:0] MII next page Data [15:8] 11.11 11.12 11.12.1 Group F Address CPU Access Group 11.12.1.1 GCR-GLOBAL CONTROL REGISTER * * CPU Address: hF00 Accessed by CPU and serial interface. (R/W) 7 5 4 Init Bit [0]: Bit[1]: Bit[2]: 3 Reset 2 Bist 1 SR 0 SC Store configuration (Default = 0) Write '1' followed by '0' to store configuration into external EEPROM Store configuration and reset (Default = 0) Write '1' to store configuration into external EEPROM and reset chip Start BIST (Default = 0) Write '1' followed by '0' to start the device's built-in self-test. The result is found in the DCR register. Soft Reset (Default = 0) Write '1' to reset the chip Initialization Done (Default = 0) This bit is meaningless when CPU is not installed. In managed mode, CPU write this bit with "1" to indicate initialization is completed and ready to forward packets. 1 - initialization is done 0 - initialization is not completed. Bit[3]: Bit[4]: 124 Zarlink Semiconductor Inc. Data Sheet Bit[7] Interrupt Polarity (Default = 0) 1 - interrupt active high 0 - interrupt active low MVTX2804 11.12.1.2 DCR-DEVICE STATUS AND SIGNATURE REGISTER * * CPU Address: hF01 Accessed by CPU and serial interface. (RO) 7 Revision Bit [0]: Bit[1]: Bit[2]: Bit[3]: Bit[5:4]: 6 5 Signature 4 3 RE 2 BinP 1 BR 0 BW 1 - Busy writing configuration to I2C 0 - Not Busy writing configuration to I2C 1 - Busy reading configuration from I2C 0 - Not Busy reading configuration from I2C 1 - BIST in progress 0 - BIST not running 1 - RAM Error 0 - RAM OK Device Signature 00 - 4 Ports Device, non-management mode 01 - 8 Ports Device, non-management mode 10 - 4 Ports Device, management mode possible (need to install CPU) 11 - 8 Ports Device, management mode possible (need to install CPU) Revision Bit [7:6]: 11.12.1.3 DCR01-GIGA PORT STATUS * * CPU Address: hF02 Accessed by CPU and serial interface. (RO) 7 CIC Bit [1:0]: Giga port 0 strap option - 00 - 100Mb MII mode - 01 - 2G mode - 10 - GMII - 11 - PCS Giga port 1 strap option - 00 - 100Mb MII mode - 01 - Reserved - 10 - GMII - 11 - PCS Chip initialization completed. Note: DCR01[7], DCR23[7], DCR45[7] and DCR67[7] have the same function. 6 43 2 GIGA1 1 0 GIGA0 Bit[3:2] Bit [7] Zarlink Semiconductor Inc. 125 MVTX2804 11.12.1.4 DCR23-GIGA PORT STATUS * * CPU Address: hF03 Accessed by CPU and serial interface. (RO) 7 CIC Bit [1:0]: Data Sheet 6 43 2 GIGA3 1 0 GIGA2 Giga port 2 strap option- 00 - 100Mb MII mode - 00 - 100Mb MII mode - 01 - Reserved - 10 - GMII - 11 - PCS Giga port 3 strap option - 00 - 100Mb MII mode - 01 - 2G mode - 10 - GMII - 11 - PCS Chip initialization completed Bit[3:2] Bit [7] 11.12.1.5 DCR45-GIGA PORT STATUS * * CPU Address: hF04 Accessed by CPU and serial interface. (RO) 7 CIC 6 43 GIGA5 21 0 GIGA4 Bit [1:0]: Giga port 4 strap option - 00 - 100Mb MII mode - 01 - Reserved - 10 - GMII - 11 - PCS Giga port 5 strap option - 00 - 100Mb MII mode - 01 - 2G mode - 10 - GMII - 11 - PCS Chip initialization completed Bit[3:2] Bit [7] 126 Zarlink Semiconductor Inc. Data Sheet 11.12.1.6 DCR67-GIGA PORT STATUS * * CPU Address: hF05 Accessed by CPU and serial interface. (RO) 7 CIC Bit [1:0]: Giga port 6 strap option - 00 - 100Mb MII mode - 01 - 2G mode - 10 - GMII - 11 - PCS Giga port 7 strap option - 00 - 100Mb MII mode - 01 - Reserved - 10 - GMII - 11 - PCS Chip initialization completed MVTX2804 6 43 2 GIGA7 1 GIGA6 0 Bit[3:2] Bit [7] 11.12.1.7 DPST - DEVICE PORT STATUS REGISTER * * CPU Address:hF06 Accessed by CPU and serial interface (R/W) Bit[2:0]: Read back index register. This is used for selecting what to read back from DTST. (Default 00) - 3'B000 - Port 0 Operating mode and Negotiation status - 3'B001 - Port 1 Operating mode and Negotiation status - 3'B010 - Port 2 Operating mode and Negotiation status - 3'B011 - Port 3 Operating mode and Negotiation status - 3'B100 - Port 4 Operating mode and Negotiation status - 3'B101 - Port 5 Operating mode and Negotiation status - 3'B110 - Port 6 Operating mode and Negotiation status - 3'B111 - Port 7 Operating mode and Negotiation status Zarlink Semiconductor Inc. 127 MVTX2804 11.12.2 DTST - Data Read Back Register * * CPU Address: hF07 Accessed by CPU and serial interface (RO) 7 MD 6 InfoDet 5 SigDet 4 Giga 3 lnkdn 2 FE 1 Fdpx 0 Fc_en Data Sheet This register provides various internal information as selected in DPST bit[2:0] Bit[0]: Bit[1]: Bit[2]: Bit[3]: Bit[4]: Bit[5]: Bit[6]: Bit[7]: Flow control enabled Full duplex port Fast ethernet port (if not giga) Link is down GIGA port Signal detect (when PCS interface mode) Pipe signal detected (pipe mode only) Module detected (for hot swap purpose) 128 Zarlink Semiconductor Inc. Data Sheet 12.0 12.1 1 MVTX2804 BGA and Ball Signal Description BGA Views (Top-View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arlink Semiconductor Inc. 129 MVTX2804 12.2 1 A B D D E F G H J K L M N P R T U V W Y AA AB AC AD AE AF AG AH AJ AK 2 Data Sheet Power and Ground Distribution 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 AVD NC9 SCA LB_D LB_D LB_D LB_D LB_D LB_D LB_D LB_D LB_D LB_D LB_D LB_D S_CL LB_D LB_A LB_A LB_A LB_A B_A[ B_A[ B_A[ B_A[ B_OE B_D[ B_D[ NC4 NC3 D N EN [0] [4] [5] [10] [16] [19] [26] [31] [32] [36] [40] [45] K [60] [3] [7] [11] [15] 16] 12] 7] 2] # 27] 26] DEV_ LA_D NC7 LB_D LB_D LB_D LB_D LB_D LB_D LB_D LB_C LB_D LB_D LB_D LB_D LB_D LB_D LB_D LB_A LB_A LB_A B_A[ B_A[ B_A[ B_A[ B_W B_D[ DEV_ NC5 B_D[ CF[0] [0] [1] [3] [6] [12] [17] [20] [28] S0# [33] [37] [41] [47] [54] [58] [62] [6] [10] [13] 17] 13] 8] 3] E# 30] CFG[ 25] LA_D LA_C LA_D NC6 LB_D LB_D LB_D LB_D LB_D LB_D LB_R LB_D LB_D LB_D LB_D LB_D LB_D LB_D LB_A LB_A LB_A B_A[ B_A[ B_A[ B_A[ B_A[ B_D[ AVD B_CL B_D[ [1] LK [3] [2] [8] [15] [18] [21] [29] W# [34] [39] [43] [48] [52] [57] [61] [4] [8] [12] 18] 14] 11] 5] 4] 28] D K 22] LA_D LA_D LA_D NC8 LB_C LB_D LB_D LB_D LB_D LB_D LB_D LB_D LB_D LB_D LB_D LB_D LB_D LB_D LB_A LB_A LB_A LB_A B_A[ B_A[ B_AD NC2 B_D[ B_D[ B_D[ B_D[ [2] [5] [9] LK [9] [13] [23] [22] [24] [25] [35] [42] [44] [50] [51] [55] [63] [14] [18] [16] [19] 9] 10] SC# 29] 24] 18] 21] LA_D LA_D LA_D LA_D AGN LB_D LB_D LB_D LB_D LB_D LB_C LB_D LB_D LB_D LB_D LB_D LB_D LB_A LB_A LB_A LB_A B_A[ B_A[ B_D[ AGN B_D[ B_D[ B_D[ B_D[ B_D[ [8] [7] [6] [4] D [7] [14] [11] [27] [30] S1# [38] [46] [49] [53] [56] [59] [5] [9] [17] [20] 15] 6] 31] D 17] 23] 19] 16] 14] LA_D LA_D LA_D LA_D LA_D VSS VSS [10] [11] [12] [13] [14] LA_D LA_D LA_D LA_D LA_D VDD [15] [16] [19] [18] [17] LA_D LA_D LA_D LA_D LA_D [20] [21] [22] [29] [24] LA_D LA_D LA_D LA_D LA_D VDD [23] [25] [26] [27] [31] LA_D LA_D LA_C LA_D LA_D VDD [28] [30] S0# [37] [33] LA_C LA_R LA_D LA_D LA_D S1# W# [32] [46] [41] LA_D LA_D LA_D LA_D LA_D VD33 [34] [35] [36] [53] [48] LA_D LA_D LA_D LA_D LA_D VD33 [38] [40] [42] [61] [56] LA_D LA_D LA_D LA_A LA_D VD33 [43] [44] [45] [4] [39] LA_D LA_D LA_D LA_D LA_D VSS [49] [50] [51] [52] [47] LA_D LA_D LA_D LA_D LA_A VSS [58] [57] [55] [54] [7] LA_D LA_D LA_D LA_D LA_A VD33 [63] [62] [60] [59] [11] LA_A LA_A LA_A LA_A LA_A VD33 [6] [5] [3] [14] [18] LA_A LA_A LA_A LA_A G0_T VD33 [10] [9] [8] [20] XD[1] LA_A LA_A LA_A G0_C G0_T [15] [13] [12] RS/L XD[4] LA_A LA_A LA_A GRE G0_T VDD [19] [17] [16] FC[0] XD[7] MIITX G0_T G0_T G0_T G0_T VDD CK[0] XD[2] XD[0] XCLK X ER G0_R G0_T G0_T G0_R G0_R XCLK XD[5] XD[3] XD[2] XD[6] G0_R G0_T G0_C G0_T G0_R VSS XD[0] X EN OL XD[6] X DV G0_R G0_R G0_R G0_R G1_T VSS VDD XD[5] XD[4] XD[3] XD[1] XD[0] VDD VDD VD33 VD33 VD33 VSS VSS VD33 VD33 VD33 VDD VDD VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDD VDD VD33 VD33 VD33 VSS VSS VD33 VD33 VD33 VDD VDD VSS VSS NC1 B_D[ B_D[ B_D[ B_D[ 9] 10] 11] 12] VDD B_D[ B_D[ B_D[ B_D[ B_D[ 20] 4] 3] 6] 7] B_D[ B_D[ P_IN B_D[ B_D[ 15] 8] T# 1] 2] VDD B_D[ P_A[ P_A[ P_W P_RD 13] 1] 2] E# # VDD B_D[ P_D[ P_D[ P_D[ P_D[ 5] 15] 11] 12] 13] P_CS P_D[ P_D[ P_D[ P_D[ # 14] 7] 8] 10] VD33 P_A[ B_D[ P_D[ P_D[ P_D[ 0] 0] 3] 4] 5] VD33 P_D[ P_D[ P_D[ P_D[ P_D[ 6] 9] 0] 1] 2] VD33 T_D[ T_D[ T_D[ T_D[ T_D[ 15] 11] 12] 13] 14] VSS T_D[ T_D[ T_D[ T_D[ T_D[ 10] 5] 7] 8] 9] VSS T_D[ T_D[ T_D[ T_D[ T_D[ 6] 4] 2] 1] 0] VD33 S_RS T_D[ TMO TMO RES T# 3] DE[1] DE[0] OUT# VD33 G7_R G7_R LESY LE_C LE_D XD[7] X ER NO# LK0 O VD33 G7_R G7_R G7_R G7_R G7_R XD[3] XD[1] X DV XD[6] XD[5] G7_T G7_T G7_R G7_R G7_R XD[6] X EN XD[4] XD[2] XD[0] VDD G7_T G7_T G7_C G7_R MIITX XD[0] XD[3] OL XCLK CK[7] VDD G6_R G7_T G7_T G7_T G7_T XD[7] X ER XD[7] XD[5] XD[4] G6_R G6_R G7_T G7_T G7_C XD[2] XD[4] XD[2] XD[1] RS/L VDD G6_R G6_R G7_T GRE G6_R XD[0] X ER XCLK FC[7] X DV VSS VSS G6_T G6_R G6_R G6_R G6_R XD[7] XD[6] XD[5] XD[3] XD[1] G0_R G0_R GRE G1_R G1_R G1_R G2_T G2_T G2_R G2_R G2_R G3_T G3_T G3_C G3_R G3_R IND_ G3_R G3_R G4_T G4_R G4_R G5_T G5_T G5_T G5_R G6_R G6_T G6_C G6_T XD[7] X ER FC[1] XD[2] XD[5] XD[7] XD[0] XD[7] XD[2] XD[4] XD[5] XD[1] XD[6] OL XD[3] XD[6] CM XD[4] X ER XD[3] XD[1] XD[4] XD[2] XD[4] X ER XD[5] XCLK XD[6] OL X ER G1_T G1_T G1C G1_T G2_T G1_R G2_T G2_T G2_R G2_R G2_R G2_R G3_T G3_R G3_R G3_R GRE M_M G4_T G4_R G4_R G4_R G5_C G5_T MIITX G5_R G6_T G6_T G6_T G6_T XD[1] XCLK RS/L XD[7] XCLK XD[4] XD[4] XD[3] XD[3] XCLK XD[7] X ER X EN XD[0] XD[5] XD[7] FC[4] DIO XD[1] XD[5] XD[6] XD[7] RS/L XD[5] CK[5] XD[1] XD[3] XD[4] X EN XD[5] G1_T G1_T MIITX G1_R G1_R G2C MIITX G2_T G2_R G2_R G3_T G3_T G3_T G3_R G3_R G3_R G4_T G4_T G4_T G4_T G4_R G4_R G4_R G5_T G5_T G5_R G5_R G6_T G6_T G6PT XD[2] XD[3] CK[1] XD[0] XCLK RS/L CK[2] X EN XD[1] X DV XCLK XD[3] XD[5] XCLK XD[2] X DV XCLK XD[4] XD[6] X ER XCLK X DV X ER XD[3] X EN XD[3] XD[6] XD[1] XD[2] CLK G1_T G1_T G1_T G1_C G1_R GRE G2_T G2_T G2_R G2_R GRE G3_T MIITX G3_T G3_R M_M G4_T G4_T G4_T G4_R G4_C GRE G5_T G5_T G5_R G5_C G5_R G5_R G6_C G6_T XD[5] XD[4] X ER OL XD[6] FC[2] XD[2] XD[6] XD[0] XD[6] FC[3] XD[2] CK[3] X ER XD[1] DC XD[0] XD[5] XD[7] XD[0] OL FC[5] XD[0] XD[6] XD[0] OL XD[4] X ER RS/L XD[0] G1_T G1_T G1_R G1_R G1_R G1_R G2_T G2_T G2_T G2_C G3_C G3_T G3_T G3_T CM_ G4C G4_T MIITX G4_T G4_R G4_R G5_T G5_T G5_T G5_R G5_R G5_R G5_R MIITX GRE XD[6] X EN XD[1] XD[3] X DV X ER XD[1] XD[5] X ER OL RS/L XD[0] XD[4] XD[7] CLK RS/L XD[2] CK[4] X EN XD[2] XD[3] XCLK XD[1] XD[7] XD[2] XCLK XD[7] X DV CK[6] FC[6] 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 130 Zarlink Semiconductor Inc. Data Sheet 12.3 Ball-Signal Descriptions MVTX2804 All pins are CMOS type; all Input pins are 5 Volt tolerance, and all output pins are 3.3 CMOS drive. 12.3.1 Ball Signal Description in Managed Mode Ball No(s) Symbol I/O Description CPU Bus Interface K27, L27, K30, K29, K28, L30, N27, L29, L28, N26, M30, M29, M28, N30, N29, N28 J28, J27, M26 J29 J30 L26 H28 Frame Buffer Interface U1, U2, N4, U3, U4, T1, T2, N5, T3, T4, M4, R4, R3, R2, R1, M5, R5, L4, P3, P2, P1, N3, L5, N2, P5, N1, K4, M3, M2, M1, K5, L3, J5, K2, H4, K1, J4, J3, J2, H5, J1, H3, H2, H1, G3, G4, G5, G2, G1, F5, F4, F3, F2, F1, D3, E1, E2, E3, D2., E4, C3, D1, C1, B2 AA1, V5, AA2, AA3, Y1, V4, Y2, Y3, U5, W1, W2, W3, T5, V1, V2, P4, V3 W4 C2 K3 L1 L2 LA_D[63:0] I/O-TS with pull up Frame Bank A- Data Bit [63:0] P_DATA[15:0] I/O-TS with pull up Processor Bus Data Bit [15:0] P_A[2:0] P_WE# P_RD# P_CS# P_INT# Input Input with weak internal pull up Input with weak internal pull up Input with weak internal pull up Output Processor Bus Address Bit [2:0] CPU Bus-Write Enable CPU Bus-Read Enable Chip Select CPU Interrupt LA_A[19:3] Output Frame Bank A - Address Bit [19:3] LA_A[20] LA_CLK LA_CS0# LA_CS1# LA_RW# Output with pull up Output Output with pull up Output with pull up Output with pull up Frame Bank A - Address Bit [20] Frame Bank A Clock Input Frame Bank A Low Portion Chip Selection Frame Bank A High Portion Chip Selection Frame Bank A Read/Write Zarlink Semiconductor Inc. 131 MVTX2804 Ball No(s) CPU Bus Interface D18, B18, C18, A17, E17, B17, C17, E16, D17, B16, E15, C16, D16, D15, E14, C15, B15, E13, A15, D14, C14, D13, B14, A14, C13, E12, B13, A13, D12, C12, B12, A12, A11, E10, C10, B10, E9, A10, D11, D10, D8, D9, C9, B9, A9, C8, B8, A8, C7, E7, D7, B7, E8, A7, D6, C6, E6, B6, A6, A5, B5, C5, B4,A4 LB_D[63:0] I/O-TS with pullup Symbol I/O Description Data Sheet Frame Bank B- Data Bit [63:0] Ball No(s) D22, D20, E20, D21, A21, D19, B21, C21, A20, B20, E19, C20, A19, B19, E18, C19, A18 E21 D5 B11 E11 C11 Switch Database Interface E24,B27, D27, C27, A27, A28, B30, D28, E27, C30, D30, G26, E28, D29, E26, E29, H26, E30, J26, F30, F29, F28, F27, H27, G30, G29, K26, G27, G28, H30, H29, M27 C22, B22, A22, E22, C23, B23, A23, C24, D24, D23, B24, A24, E23, C25, C26, B25, A25 C29 D25 B26 A26 MII Management Interface Symbol LB_A[19:3] Output I/O Description Frame Bank B - Address Bit [19:3] LB_A[20] LB_CLK LB_CS0# LB_CS1# LB_RW# Output with pull up Output Output with pull up Output with pull up Output with pull up Frame Bank B - Address Bit [20] Frame Bank B Clock Input Frame Bank B Low Portion Chip Selection Frame Bank B High Portion Chip Selection Frame Bank B Read/Write B_D[31:0] I/O-TS with pull up Switch Database Domain - Data Bit [31:0] B_A[18:2] Output Switch Database Address (512K) - Address Bit [18:2] B_CLK B_ADSC# B_WE# B_OE# Output Output with pull up Output with pull up Output with pull up Switch Database Clock Input Switch Database Address Status Control Switch Database Write Chip Select Switch Database Read Chip Select 132 Zarlink Semiconductor Inc. Data Sheet Ball No(s) AJ16 AG18 Symbol M_MDC M_MDIO Output I/O-TS with pull up I/O MVTX2804 Description MII Management Data Clock (common for all MII Ports [7:0]) MII Management Data I/O (common for all MII Ports -[7:0])) 2.5Mhz Giga Reference Clock GMII / MII Interface (193) Gigabit Ethernet Access Port AD29, AK30, AJ22, AG17, AJ11, AJ6, AF3,AA4 AK15 AF17 GREF_CLK [7:0] Input w/ pull up CM_CLK IND/CM Input w/ pull up Input w/ pull up Common Clock shared by port G[7:0] 1: select GREF_CLK[7:0] as clock 0: select CM_CLK as clock for all ports Input w/ pull up AA30, AK29, AG25, AK18, AJ13, AH7, AH3, AB1 V26, W29, W30, Y28, W26, Y29, W27, Y30, AB26, AE27, AE28, AC27, AE29, AC26, AE30, AD26 AK27, AH27, AF26, AJ27, AH26, AK25, AG26, AJ25 MII TX CLK[7:0] Input w/ pull up G7_RXD[7:0] Input w/ pull up G[7:0] port - Receive Data Bit [7:0] G6_RXD[7:0] G5_RXD[7:0] G4_RXD[7:0] AG22, AG21, AG20, AF22, AK21, AK20, AF21, AJ20 AG16, AF16, AG15, AF18, AF15, AH15, AJ15, AG14 AG11, AJ10, AF11, AF10, AG9, AF9, AH9, AJ9 AF6, AJ5, AF5, AG6, AK4, AF4, AK3, AH4 AF1, AC5, AE1, AE2, AE3, AC4, AE4, AD1 W28, AD30, AK28, AH22, AH16, AH10, AK5, AD5 V27, AD27, AJ28, AH23, AF19, AG12, AK6, AF2 AC30, AJ29, AG23, AK16, AK11, AH6, AG3, Y4 G[7:0]_RX_DV G[7:0]_RX_ER G[7:0]_CRS/LINK Input w/ pull down Input w/ pull up Input w/ pull down G[7:0]port - Receive Data Valid G[7:0]port - Receive Error G[7:0]port - Carrier Sense G3_RXD[7:0] G2_RXD[7:0] G1_RXD[7:0] G0_RXD[7:0] Zarlink Semiconductor Inc. 133 MVTX2804 Ball No(s) AA28, AF29, AJ26, AJ21, AF14, AK10, AJ4, AD3 AA29, AF27, AK26, AH21, AH14, AG10, AH5, AC1 AB28, Y26, AB29, AB30, AA27, AC28, AC29, AA26 AE26, AF28, AG30, AG28, AG27, AH29, AH28, AJ30 AK24, AJ24, AG24, AF24, AH24, AF23, AK23, AJ23 AJ19, AH19, AJ18, AH18, AF20, AK17, AG19, AJ17 AK14, AF13, AH13, AK13, AH12, AJ12, AF12, AK12 AF8, AJ8, AK8, AG7, AG8, AJ7, AK7, AF7 AG4, AK1, AJ1, AJ2, AH2, AH1, AG1, AE5 AA5, AD4, AC2, Y5, AC3, AB2, W5, AB3 Y27, AG29, AH25, AK19, AG13, AH8, AK2, AD2 AB27, AF30, AF25, AH20, AJ14, AK9, AJ3, AB5 AD28, AH30, AK22, AH17, AH11, AG5, AG2, AB4 AD29, AK30, AJ22, AG17, AJ11, AJ6, AF3,AA4 AK15 AF17 G[7:0]_TX_EN G[7:0]_TX_ER Output w/ pull up Output w/ pull up Symbol G[7:0]_COL I/O Input w/ pull up Description Data Sheet G[7:0]port - Collision Detected G[7:0]_RXCLK Input w/ pull up G[7:0]port - Receive Clock G7_TXD[7:0] Output G[7:0]port - Transmit Data Bit [7:0] G6_TXD[7:0] G5_TXD[7:0] G4_TXD[7:0] G3_TXD[7:0] G2_TXD[7:0] G1_TXD[7:0] G0_TXD[7:0] G[7:0]port - Transmit Data Enable G[7:0]port - Transmit Error G[7:0]_ TXCLK Output G[7:0]port - Gigabit Transmit Clock PMA Interface (193) Gigabit Ethernet Access Port (PCS) GREF_CLK [7:0] Input w/ pull up Gigabit Reference Clock CM_CLK IND/CM Input w/ pull up Input w/ pull up Common Clock shared by port G[7:0] I: select GREF_CLK[7:0] as clock 0: select CM_CLK as clock for all port 134 Zarlink Semiconductor Inc. Data Sheet Ball No(s) V26, W29, W30, Y28, W26, Y29, W27, Y30 AB26, AE27, AE28, AC27, AE29, AC26, AE30, AD26 AK27, AH27, AF26, AJ27, AH26, AK25, AG26, AJ25 G4_RXD[7:0] AG22, AG21, AG20, AF22, AK21, AK20, AF21, AJ20 AG16, AF16, AG15, AF18, AF15, AH15, AJ15, AG14 AG11, AJ10, AF11, AF10, AG9, AF9, AH9, AJ9 AF6, AJ5, AF5, AG6, AK4, AF4, AK3, AH4 AF1, AC5, AE1, AE2, AE3, AC4, AE4, AD1 W28, AD30, AK28, AH22, AH16, AH10, AK5, AD5 V27, AD27, AJ28, AH23, AF19, AG12, AK6, AF2 AA28, AF29, AJ26, AJ21, AF14, AK10, AJ4, AD3 AA29, AF27, AK26, AH21, AH14, AG10, AH5, AC1 GP[7:0]_RX_D[8] Input w/ pull down Symbol G7_RXD[7:0] I/O Input w/ pull up MVTX2804 Description G[7:0]port - PMA Receive Data Bit [7:0] G6_RXD[7:0] G5_RXD[7:0] G3_RXD[7:0] G2_RXD[7:0] G1_RXD[7:0] G0_RXD[7:0] G[7:0]port - PMA Receive Data Bit [8] G[7:0]port - PMA Receive Data Bit [9] G[7:0]port - PMA Receive Clock 1 GP[7:0]_RX_D[9] Input w/ pull up GP[7:0]_ RXCLK 1 Input w/ pull up GP[7:0]_RXCLK0 Input w/ pull up G[7:0]port - PMA Receive Clock 0 Zarlink Semiconductor Inc. 135 MVTX2804 Ball No(s) AB28, Y26, AB29, AB30, AA27, AC28, AC29, AA26 AE26, AF28, AG30, AG28, AG27, AH29, AH28, AJ30 AK24, AJ24, AG24, AF24, AH24, AF23, AK23, AJ23 AJ19, AH19, AJ18, AH18, AF20, AK17, AG19, AJ17 AK14, AF13, AH13, AK13, AH12, AJ12, AF12, AK12 AF8, AJ8, AK8, AG7, AG8, AJ7, AK7, AF7 AG4, AK1, AJ1, AJ2, AH2, AH1, AG1, AE5 AA5, AD4, AC2, Y5, AC3, AB2, W5, AB3 Y27, AG29, AH25, AK19, AG13, AH8, AK2, AD2 AB27, AF30, AF25, AH20, AJ14, AK9, AJ3, AB5 AD28, AH30, AK22, AH17, AH11, AG5, AG2, AB4 Test Facility (3) U29 T_MODE0 I/O-TS with pull up GP[7:0]_TXD[8] GP[7:0]_TXD[9] Output w/ pull up Output w/ pull up Symbol G7_TXD[7:0] Output I/O Description Data Sheet G[7:0]port - PMA Transmit Data Bit [7:0] G6_TXD[7:0] G5_TXD[7:0] G4_TXD[7:0] G3_TXD[7:0] G2_TXD[7:0] G1_TXD[7:0] G0_TXD[7:0] G[7:0]port - PMA Transmit Data Bit [8] G[7:0]port - PMA Transmit Data Bit [9] G[7:0]port - PMA Gigabit Transmit Clock G[7:0]_ TXCLK Output Test - Set upon Reset, and provides NAND Tree test output during test mode Use external Pull up for normal operation Test - Set upon Reset, and provides NAND Tree test output during test mode Use external Pull up for normal operation Enable test mode For normal operation leave it open U28 T_MODE1 I/O-TS with pull up A3 SCAN_EN Input w/ pull down LED Interface (serial and parallel) 136 Zarlink Semiconductor Inc. Data Sheet Ball No(s) R28, T26, R27, T27, U27, T28, T29, T30 Symbol T_D[7:0]/ LE_PD[7:0] P26, P30, P29, P28, P27, R26, R30, R29 T_D[15:8]/ LE_PT[7:0] Output Output I/O MVTX2804 Description While resetting, T_D[7,0] are in input mode and are used as strapping pins. Internal pullup LE_PD - Parallel Led data [7:0] While resetting, T_D[15:8] are in input mode and are used as strapping pins. Internal pullup LED_PR[7:0] - Parallel Led port sel [7:0] V29 LE_CLK0/ LE_PT[8] Output LE_CLK0 - LED Serial Interface Output Clock LE_PT[8] - Parallel Led port sel [8] V30 LED_BLINK/ Output LE_DO/ LE_PT[9] While resetting, LED-BLINK is in input mode and is used as strapping pin. 1: No Blink, 0: Blink. Internal pullup. LE_DO - LED Serial Data Output Stream LE_PT[9] - Parallel Led port sel [9] V28 LED_PM/ LE_SYNCO# Output w/ pull up While resetting, LED_PM is in input mode and is used as strapping pin. Internal pull up. 1: Enable parallel interface, 0: enable serial interface. LE_SYNCO# - LED Output Data Stream Envelop System Clock, Power, and Ground Pins A16 U26 U30 B1 B28 AE7, AE9, F10, F21, F22, F9, G25, G6, J25, J6, K25, K6, AA25, AA6, AB25, AB6, AD25, AE10, AE21, AE22 S_CLK S_RST# RESOUT# DEV_CFG[0] DEV_CFG[1]I VDD Input Input - ST Output Input w/ pull down Input w/ pull down Power core System Clock at 133 MHz Reset Input Reset PHY Not used Not used +2.5 Volt DC Supply Zarlink Semiconductor Inc. 137 MVTX2804 Ball No(s) V14, V15, V16, V17, V18, F16, F24, F25, F6, F7, N13, N14, N15, N16, N17, N18, P13, P14, P15, P16, P17, P18, R13, R14, R15, R16, R17, R18, R25, R6, T13, T14, T15, T16, T17, T18, T25, T6, U13, U14, U15, U16, U17, U18, V13, AD6, AE15, AE16, AE24, AE25, AE6, F15 A1, C28 E5, E25 AE12, AE13, AE14, AE17, AE18, AE19, F12, F13, F14, F17, F18, F19, M25, M6, N25, N6, P25, P6, U25, U6, V25, V6, W25, W6 AD2,AB5 Symbol VSS Ground I/O Ground Description Data Sheet AVDD AVSS VDD33 Power Ground Power I/O Analog +2.5 Volt DC Supply Analog Ground +3.3 Volt DC Supply Bootstrap Pins (Default= pull up, 1= pull up 0= pull down) G0_TX_EN G0_TX_ER Default: PCS Giga0 Mode: G0_TXEN G0_TXER 0 0 MII 0 1 Rsvd 1 0 GMII 1 1 PCS Giga1 Mode: G1_TXEN G1_TXER 0 0 MII 0 1 Rsvd 1 0 GMII 1 1 PCS Giga2 Mode: G2_TXEN G2_TXER 0 0 MII 0 1 Rsvd 1 0 GMII 1 1 PCS Giga3 Mode: G3_TXEN G3_TXER 0 0 MII 0 1 Rsvd 1 0 GMII 1 1 PCS AK2,AJ3 G1_TX_EN G1_TXER Default: PCS AH8,AK9 G2_TX_EN G2_TX_ER Default: PCS AG13,AJ14 G3_TX_EN G3_TX_ER Default: PCS 138 Zarlink Semiconductor Inc. Data Sheet Ball No(s) AK19,AH20 Symbol G4_TX_EN G4_TX_ER I/O Default: PCS MVTX2804 Description Giga4 Mode: G4_TXEN G4_TXER 0 0 MII 0 1 Rsvd 1 0 GMII 1 1 PCS Giga5 Mode: G5_TXEN G5_TXER 0 0 MII 0 1 Rsvd 1 0 GMII 1 1 PCS Giga6 Mode: G6_TXEN G6_TXER 0 0 0 1 1 0 1 1 Giga7 Mode: G7_TXEN G7_TXER 0 0 0 1 1 0 1 1 Giga link active status 0 - active low 1 - active high Power saving 0 - No power saving 1 - Power saving Stop MAC clock if no MAC activity. Reserved - Must be pulled-down Hot plug port module detection enable 0 - module detection enable 1 - module detection disable Reserved - Must be pulled-down SRAM memory size 0 - 512K SRAM 1 - 256K SRAM CPU Port mode 0 - 8 bit cpu data bus 1 - 16 bit cpu data bus FDB memory depth 1- one memory layer 0 - two memory layers AH25,AF25 G5_TX_EN G5_TX_ER Default: PCS AG29,AF30 G6_TX_EN G6_TX_ER Default: PCS MII Rsvd GMII PCS Y27,AB27 G7_TX_EN G7_TX_ER Default: PCS MII Rsvd GMII PCS After reset T_d[15:0] are used by the LED interface T30 T_d[0] 1 T29 T_d[1] 1 T28 U27 T_d[2] T_d[3] Must be pulled-down 1 T27 R27 T_d[4] T_d[5] Must be pulled-down 1 T26 T_d[6] 1 R28 T_d[7] 1 Zarlink Semiconductor Inc. 139 MVTX2804 Ball No(s) W4, E21 Symbol La_a[20], Lb_a[20] 1 I/O Description Data Sheet FDB memory size 11 - 2M per bank = 4M total 10 - 1M per bank = 2M total 0x - 512K per bank = 1M total EEPROM installed 0 - EEPROM is installed 1 - EEPROM is not installed MCT Aging enable 0 - MCT aging disable 1 - MCT aging enable FCB handle aging enable 0 - FCB handle aging disable 1 - FCB handle aging enable Timeout reset enable 0 - timeout reset disable 1 - timeout reset enable Issue reset if any state machine did not go back to idle for 5sec. Reserved CPU installed 0 - CPU installed 1 - CPU is not installed External RAM test 0 - Perform the infinite loop of ZBT RAM BIST. Debug test only 1 - Regular operation. ZBT RAM la_clk turning 3'b000 - control by reg. LCLKCR[2:0] 3'b001 - delay by method # 0 3'b010 - delay by method # 1 3'b011 - delay by method # 2 3'b100 - delay by method # 3 3'b101 - delay by method # 4 3'b110 - delay by method # 5 3'b111 - delay by method # 6 USE METHOD 6 FOR NORMAL OPERATION. External pull up not required R29 T_d[8] 1 R30 T_d[9] 1 R26 T_d[10] 1 P27 T_d[11] 1 P28, P29 P30 T_d[13:12] T_d[14] 1 1 P26 T_d[15] 1 After reset P_d[8:0] are used by the CPU bus interface N30, N29, N28 P_d[2:0] 111 140 Zarlink Semiconductor Inc. Data Sheet Ball No(s) M30, M29, M28 Symbol P_d[5:3] 111 I/O MVTX2804 Description ZBT RAM lb_clk turning 3'b000 - control by reg. LCLKCR[6:4] 3'b001 - delay by method # 0 3'b010 - delay by method # 1 3'b011 - delay by method # 2 3'b100 - delay by method # 3 3'b101 - delay by method # 4 3'b110 - delay by method # 5 3'b111 - delay by method # 6 USE METHOD 6 FOR NORMAL OPERATION. External pull up not required L29, L28, N26 P_d[8:6] 111 SBRAM b_clk turning 3'b000 - control by BCLKCR[2:0] 3'b001 - delay by method # 0 3'b010 - delay by method # 1 3'b011 - delay by method # 2 3'b100 - delay by method # 3 3'b101 - delay by method # 4 3'b110 - delay by method # 5 3'b111 - delay by method # 6 USE METHOD 6 FOR NORMAL OPERATION. External pull up not required Notes #= Input = In-ST = Output = Out-OD= I/O-TS = I/O-OD = Active low signal Input signal Input signal with Schmitt-Trigger Output signal (Tri-State driver) Output signal with Open-Drain driver Input & Output signal with Tri-State driver Input & Output signal with Open-Drain driver Zarlink Semiconductor Inc. 141 MVTX2804 12.3.2 Ball - Signal Description in Unmanaged Mode Ball No(s) K27, L27, K30, K29, K28 L30 Symbol P_DATA[15:11] P_DATA[10] I/O I/O-TS with pull up I/O - TS with pull up Description Data Sheet Not used - leave unconnected Trunk enable in unmanaged mode External pull up or unconnected disable trunk group 0 and 1 External pull down - enable trunk group 0 and 1 See register TRUNK0_MODE for port selection and trunk enable. N27 P_DATA[9] I/O - TS with pull up Trunk enable in unmanaged mode External pull up or unconnected disable trunk group 2 and 3 External pull down - enable trunk group 2 and 3 See register TRUNK1_MODE for port selection and trunk enable L29, L28, N26, M30, M29, M28, N30, N29, N28 J28 H28 P_DATA[8:0] P_A[2] P_INT# I/O - TS with pull up Input Output with internal weak pullup Output I/O-TS with pull up Input with weak internal pull up Input with weak internal pull up Output with pull up I/O-TS with pull up Bootstrap function - See bootstrap section Not used - leave unconnected Not used - leave unconnected I2C Interface (0) Note: In unmanaged mode, Use I2C and Serial control interface to configure the system J27 M26 Serial Control Interface J29 L26 J30 Frame Buffer Interface U1, U2, N4, U3, U4,T1,T2, N5, T3, T4, M4, R4, R3, R2, R1, M5, R5, L4, P3, P2, P1, N3,L5, N2, P5, N1, K4, M3, M2, M1, K5, L3, J5, K2, H4, K1, J4, J3, J2, H5, J1, H3, H2, H1, G3, G4, G5, G2, G1, F5, F4, F3, F2, F1, D3, E1,E2,E3, D2., E4, C3, D1, C1, B2 LA_D[63:0] Frame Bank A- Data Bit [63:0] PS_STROBE PS_DO PS_DI (AUTOFD) Serial Strobe Pin Serial Data Input Serial Data Output (AutoFD) SCL SDA I2C Data Clock I2C Data I/O 142 Zarlink Semiconductor Inc. Data Sheet Ball No(s) AA1, V5, AA2, AA3, Y1, V4, Y2, Y3, U5, W1, W2, W3, T5, V1, V2, P4, V3 W4 C2 K3 L1 L2 D18, B18, C18, A17, E17, B17, C17, E16, D17, B16, E15, C16, D16, D15, E14, C15, B15, E13, A15, D14, C14, D13, B14, A14, C13, E12, B13, A13, D12, C12, B12, A12, A11, E10, C10, B10, E9, A10, D11, D10, D8, D9, C9, B9, A9, C8, B8, A8, C7, E7, D7, B7, E8, A7, D6, C6, E6, B6, A6, A5, B5, C5, B4,A4 D22, D20, E20, D21, A21, D19, B21, C21, A20, B20, E19, C20, A19, B19, E18, C19, A18 E21 D5 B11 E11 C11 Switch Database Interface E24,B27, D27, C27, A27, A28, B30, D28, E27, C30, D30, G26, E28, D29, E26, E29, H26, E30, J26, F30, F29, F28, F27, H27, G30, G29, K26, G27, G28, H30, H29, M27 C22, B22, A22, E22, C23, B23, A23, C24, D24, D23, B24, A24, E23, C25, C26, B25, A25 C29 B_D[31:0] Output with pull up Symbol LA_A[19:3] Output I/O MVTX2804 Description Frame Bank A - Address Bit [19:3] LA_A[20] LA_CLK LA_CS0# LA_CS1# LA_RW# LB_D[63:0] Output with pull up Output Output with pull up Output with pull up Output with pull up I/O-TS with pull up Frame Bank A - Address Bit [20] Frame Bank A Clock Input Frame Bank A Low Portion Chip Selection Frame Bank A High Portion Chip Selection Frame Bank A Read/Write Frame Bank B- Data Bit [63:0] LB_A[19:3] Output Frame Bank B - Address Bit [19:3] LB_A[20] LB_CLK LB_CS0# LB_CS1# LB_RW# Output with pull up Output Output with pull up Output with pull up Output with pull up Frame Bank B - Address Bit [20] Frame Bank B Clock Input Frame Bank B Low Portion Chip Selection Frame Bank B High Portion Chip Selection Frame Bank B Read/Write Switch Database Domain - Data Bit [31:0] B_A[18:2] Output Switch Database Address (512K) - Address Bit [18:2] B_CLK Output Switch Database Clock Input Zarlink Semiconductor Inc. 143 MVTX2804 Ball No(s) D25 B26 A26 MII Management Interface AJ16 AG18 M_MDC M_MDIO Output I/O-TS with pull up Symbol B_ADSC# B_WE# B_OE# I/O Output with pull up Output with pull up Output with pull up Description Data Sheet Switch Database Address Status Control Switch Database Write Chip Select Switch Database Read Chip Select MII Management Data Clock (common for all MII Ports [7:0]) MII Management Data I/O (common for all MII Ports -[7:0])) 2.5Mhz Ball No(s) AD29, AK30, AJ22, AG17, AJ11, AJ6, AF3,AA4 AK15 AF17 Symbol GREF_CLK [7:0] I/O Input w/ pull up Description Gigabit Reference Clock GMII / MII Interface (193) Gigabit Ethernet Access Port CM_CLK IND/CM Input w/ pull up Input w/ pull up Common Clock shared by port G[7:0] 1: select GREF_CLK[7:0] as clock 0: select CM_CLK as clock for all ports AA30, AK29, AG25, AK18, AJ13, AH7, AH3, AB1 MII TX CLK[7:0] Input w/ pull up 144 Zarlink Semiconductor Inc. Data Sheet Ball No(s) V26, W29, W30, Y28, W26, Y29, W27, Y30 AB26, AE27, AE28, AC27, AE29, AC26, AE30, AD26 AK27, AH27, AF26, AJ27, AH26, AK25, AG26, AJ25 AG22, AG21, AG20, AF22, AK21, AK20, AF21, AJ20 AG16, AF16, AG15, AF18, AF15, AH15, AJ15, AG14 AG11, AJ10, AF11, AF10, AG9, AF9, AH9, AJ9 AF6, AJ5, AF5, AG6, AK4, AF4, AK3, AH4 AF1, AC5, AE1, AE2, AE3, AC4, AE4, AD1 W28, AD30, AK28, AH22, AH16, AH10, AK5, AD5 V27, AD27, AJ28, AH23, AF19, AG12, AK6, AF2 AC30, AJ29, AG23, AK16, AK11, AH6, AG3, Y4 AA28, AF29, AJ26, AJ21, AF14, AK10, AJ4, AD3 AA29, AF27, AK26, AH21, AH14, AG10, AH5, AC1 G[7:0]_RX_DV G[7:0]_RX_ER G[7:0]_CRS/LINK Input w/ pull down Input w/ pull up Input w/ pull down Symbol G7_RXD[7:0] G6_RXD[7:0] G5_RXD[7:0] G4_RXD[7:0] G3_RXD[7:0] G2_RXD[7:0] G1_RXD[7:0] G0_RXD[7:0] I/O Input w/ pull up MVTX2804 Description G[7:0] port - Receive Data Bit [7:0] G[7:0]port - Receive Data Valid G[7:0]port - Receive Error G[7:0]port - Carrier Sense G[7:0]_COL G[7:0]_RXCLK Input w/ pull up Input w/ pull up G[7:0]port - Collision Detected G[7:0]port - Receive Clock Zarlink Semiconductor Inc. 145 MVTX2804 Ball No(s) AB28, Y26, AB29, AB30, AA27, AC28, AC29, AA26 AE26, AF28, AG30, AG28, AG27, AH29, AH28, AJ30 AK24, AJ24, AG24, AF24, AH24, AF23, AK23, AJ23 AJ19, AH19, AJ18, AH18, AF20, AK17, AG19, AJ17 AK14, AF13, AH13, AK13, AH12, AJ12, AF12, AK12 AF8, AJ8, AK8, AG7, AG8, AJ7, AK7, AF7 AG4, AK1, AJ1, AJ2, AH2, AH1, AG1, AE5 AA5, AD4, AC2, Y5, AC3, AB2, W5, AB3 Y27, AG29, AH25, AK19, AG13, AH8, AK2, AD2 AB27, AF30, AF25, AH20, AJ14, AK9, AJ3, AB5 AD28, AH30, AK22, AH17, AH11, AG5, AG2, AB4 AD29, AK30, AJ22, AG17, AJ11, AJ6, AF3,AA4 AK15 AF17 G[7:0]_TX_EN G[7:0]_TX_ER Output w/ pull up Output w/ pull up Symbol G7_TXD[7:0] G6_TXD[7:0] G5_TXD[7:0] G4_TXD[7:0] G3_TXD[7:0] G2_TXD[7:0] G1_TXD[7:0] G0_TXD[7:0] Output I/O Description Data Sheet G[7:0]port - Transmit Data Bit [7:0] G[7:0]port - Transmit Data Enable G[7:0]port - Transmit Error G[7:0]_ TXCLK Output G[7:0]port - Gigabit Transmit Clock PMA Interface (193) Gigabit Ethernet Access Port (PCS) GREF_CLK [7:0] Input w/ pull up Gigabit Reference Clock CM_CLK IND/CM Input w/ pull up Input w/ pull up Common Clock shared by port G[7:0] 1: select GREF_CLK[7:0] as clock 0: select CM_CLK as clock for all port 146 Zarlink Semiconductor Inc. Data Sheet Ball No(s) V26, W29, W30, Y28, W26, Y29, W27, Y30 AB26, AE27, AE28, AC27, AE29, AC26, AE30, AD26 AK27, AH27, AF26, AJ27, AH26, AK25, AG26, AJ25 AG22, AG21, AG20, AF22, AK21, AK20, AF21, AJ20 AG16, AF16, AG15, AF18, AF15, AH15, AJ15, AG14 AG11, AJ10, AF11, AF10, AG9, AF9, AH9, AJ9 AF6, AJ5, AF5, AG6, AK4, AF4, AK3, AH4 AF1, AC5, AE1, AE2, AE3, AC4, AE4, AD1 W28, AD30, AK28, AH22, AH16, AH10, AK5, AD5 V27, AD27, AJ28, AH23, AF19, AG12, AK6, AF2 AA28, AF29, AJ26, AJ21, AF14, AK10, AJ4, AD3 AA29, AF27, AK26, AH21, AH14, AG10, AH5, AC1 G[7:0]_RX_D[8] G[7:0]_RX_D[9] G[7:0]_RXCLK1 G[7:0]_RXCLK0 Input w/ pull down Input w/ pull up Input w/ pull up Input w/ pull up Symbol G7_RXD[7:0] G6_RXD[7:0] G5_RXD[7:0] G4_RXD[7:0] G3_RXD[7:0] G2_RXD[7:0] G1_RXD[7:0] G0_RXD[7:0] I/O Input w/ pull up MVTX2804 Description G[7:0]port - PMA Receive Data Bit [7:0] G[7:0]port - PMA Receive Data Bit [8] G[7:0]port - PMA Receive Data Bit [9] G[7:0]port - PMA Receive Clock 1 G[7:0]port - PMA Receive Clock 0 Zarlink Semiconductor Inc. 147 MVTX2804 Ball No(s) AB28, Y26, AB29, AB30, AA27, AC28, AC29, AA26 AE26, AF28, AG30, AG28, AG27, AH29, AH28, AJ30 AK24, AJ24, AG24, AF24, AH24, AF23, AK23, AJ23 AJ19, AH19, AJ18, AH18, AF20, AK17, AG19, AJ17 AK14, AF13, AH13, AK13, AH12, AJ12, AF12, AK12 AF8, AJ8, AK8, AG7, AG8, AJ7, AK7, AF7 AG4, AK1, AJ1, AJ2, AH2, AH1, AG1, AE5 AA5, AD4, AC2, Y5, AC3, AB2, W5, AB3 Y27, AG29, AH25, AK19, AG13, AH8, AK2, AD2 AB27, AF30, AF25, AH20, AJ14, AK9, AJ3, AB5 AD28, AH30, AK22, AH17, AH11, AG5, AG2, AB4 Test Facility (3) U29 T_MODE0 I/O-TS with pull up G[7:0]_TXD[8] G[7:0]_TX_D[9] Output w/ pull up Output w/ pull up Symbol G7_TXD[7:0] G6_TXD[7:0] G5_TXD[7:0] G4_TXD[7:0] G3_TXD[7:0] G2_TXD[7:0] G1_TXD[7:0] G0_TXD[7:0] Output I/O Description Data Sheet G[7:0]port - PMA Transmit Data Bit [7:0] G[7:0]port - PMA Transmit Data Bit [8] G[7:0]port - PMA Transmit Data Bit [9] G[7:0]port - PMA Gigabit Transmit Clock G[7:0]_ TXCLK Output Test - Set upon Reset, and provides NAND Tree test output during test mode Use external Pull up for normal operation U28 T_MODE1 I/O-TS with pull up Test - Set upon Reset, and provides NAND Tree test output during test mode Use external Pull up for normal operation A3 SCAN_EN Input w/ pull down Enable test mode For normal operation leave it open 148 Zarlink Semiconductor Inc. Data Sheet Ball No(s) R28, T26, R27, T27, U27, T28, T29, T30 Symbol T_D[7:0]/ LE_PD[7:0] Output I/O MVTX2804 Description While resetting, T_D[7,0] are in input mode and are used as strapping pins. Internal pullup LE_PD - Parallel Led data [7:0] While resetting, T_D[15:8] are in input mode and are used as strapping pins. Internal pullup LED_PR[7:0] - Parallel Led port sel [7:0] LE_CLK0 - LED Serial Interface Output Clock LE_PT[8] - Parallel Led port sel [8] While resetting, LED-BLINK is in input mode and is used as strapping pin. 1: No Blink, 0: Blink. Internal pullup. LE_DO - LED Serial Data Output Stream LE_PT[9] - Parallel Led port sel [9] While resetting, LED_PM is in input mode and is used as strapping pin. Internal pull up. 1: Enable parallel interface, 0: enable serial interface. LE_SYNCO# - LED Output Data Stream Envelop System Clock at 133 MHz Reset Input Reset PHY Not used Not used +2.5 Volt DC Supply LED Interface (serial and parallel) P26, P30, P29, P28, P27, R26, R30, R29 T_D[15:8]/ LE_PT[7:0] Output V29 LE_CLK0/ LE_PT[8] Output V30 LED_BLINK/ LE_DO/ LE_PT[9] Output V28 LED_PM/ LE_SYNCO# Output w/ pull up System Clock, Power, and Ground Pins A16 U26 U30 B1 B28 AE7, AE9, F10, F21, F22, F9, G25, G6, J25, J6, K25, K6, AA25, AA6, AB25, AB6, AD25, AE10, AE21, AE22 S_CLK S_RST# RESOUT# DEV_CFG[0] DEV_CFG[1] VDD Input Input - ST Output Input w/ pull down Input w/ pull down Power core Zarlink Semiconductor Inc. 149 MVTX2804 Ball No(s) V14, V15, V16, V17, V18, F16, F24, F25, F6, F7, N13, N14, N15, N16, N17, N18, P13, P14, P15, P16, P17, P18, R13, R14, R15, R16, R17, R18, R25, R6, T13, T14, T15, T16, T17, T18, T25, T6, U13, U14, U15, U16, U17, U18, V13, AD6, AE15, AE16, AE24, AE25, AE6, F15 A1, C28 E5, E25 AE12, AE13, AE14, AE17, AE18, AE19, F12, F13, F14, F17, F18, F19, M25, M6, N25, N6, P25, P6, U25, U6, V25, V6, W25, W6 AD2,AB5 Symbol VSS Ground I/O Ground Description Data Sheet AVDD AVSS VDD33 Power Ground Power I/O Analog +2.5 Volt DC Supply Analog Ground +3.3 Volt DC Supply Bootstrap Pins (Default= pull up, 1= pull up 0= pull down) G0_TX_EN G0_TX_ER Default: PCS Giga0 Mode: G0_TXEN G0_TXER 0 0 0 1 1 0 1 1 MII Rsvd GMII PCS AK2,AJ3 G1_TX_EN G1_TX_ER Default: PCS Giga1 Mode: G1_TXEN G1_TXER 0 0 MII 0 1 Rsvd 1 0 GMII 1 1 PCS Giga2 Mode: G2_TXEN G2_TXER 0 0 0 1 1 0 1 1 Giga3 Mode: G3_TXEN G3_TXER 0 0 0 1 1 0 1 1 AH8,AK9 G2_TX_EN G2_TX_ER Default: PCS MII Rsvd GMII PCS AG13,AJ14 G3_TX_EN G3_TX_ER Default: PCS MII Rsvd GMII PCS 150 Zarlink Semiconductor Inc. Data Sheet Ball No(s) Symbol I/O Default: PCS MVTX2804 Description Giga4 Mode: G4_TXEN G4_TXER 0 0 0 1 1 0 1 1 Giga5 Mode: G5_TXEN G5_TXER 0 0 0 1 1 0 1 1 Giga6 Mode: G6_TXEN G6_TXER 0 0 0 1 1 0 1 1 Giga7 Mode: G7_TXEN G7_TXER 0 0 0 1 1 0 1 1 Giga link active status 0 - active low 1 - active high Power saving 0 - No power saving 1 - Power saving Stop MAC clock if no MAC activity. Reserved - Must be pulled-down. Hot plug port module detection enable 0 - module detection enable 1 - module detection disable Reserved - Must be pulled-down. SRAM memory size 0 - 512K SRAM 1 - 256K SRAM CPU Port mode 0 - 8 bit cpu data bus 1 - 16 bit cpu data bus FDB memory depth 1- one memory layer 0 - two memory layers MII Rsvd GMII PCS Default: PCS MII Rsvd GMII PCS Default: PCS MII Rsvd GMII PCS Default: PCS MII Rsvd GMII PCS 1 1 Must be pulled-down. 1 Must be pulled-down. 1 1 1 Zarlink Semiconductor Inc. 151 Data Sheet Ball No(s) Symbol 11 I/O MVTX2804 Description FDB memory size 11 - 2M per bank = 4M total 10 - 1M per bank = 2M total 0x - 512K per bank = 1M total EEPROM installed 0 - EEPROM is installed 1 - EEPROM is not installed MCT Aging enable 0 - MCT aging disable 1 - MCT aging enable FCB handle aging enable 0 - FCB handle aging disable 1 - FCB handle aging enable Timeout reset enable 0 - timeout reset disable 1 - timeout reset enable Issue reset if any state machine did not go back to idle for 5sec. Reserved 1 CPU installed 0 - CPU installed. 1 - CPU is not installed. External RAM test 0 - Perform the infinite loop of ZBT RAM BIST. Debug test only 1 - Regular operation. ZBT RAM la_clk turning 3'b000 - control by reg. LCLKCR[2:0] 3'b001 - delay by method # 0 3'b010 - delay by method # 1 3'b011 - delay by method # 2 3'b100 - delay by method # 3 3'b101 - delay by method # 4 3'b110 - delay by method # 5 3'b111 - delay by method # 6 - USE THIS METHOD ZBT RAM lb_clk turning 3'b000 - control by reg. LCLKCR[6:4] 3'b001 - delay by method # 0 3'b010 - delay by method # 1 3'b011 - delay by method # 2 3'b100 - delay by method # 3 3'b101 - delay by method # 4 3'b110 - delay by method # 5 3'b111 - delay by method # 6 - USE THIS METHOD 1 1 1 P27 T_d[11] 1 P28,P29 P30 T_d[13:12] T_d[14] P26 T_d[15] 1 N30, N29, N28 P_d[2:0] 111 M30, M29, M28 P_d[5:3]1 Zarlink Semiconductor Inc. 152 Data Sheet Ball No(s) L29, L28, N26 Symbol P_d[8:6] 111 I/O MVTX2804 Description SBRAM b_clk turning 3'b000 - control by BCLKCR[2:0] 3'b001 - delay by method # 0 3'b010 - delay by method # 1 3'b011 - delay by method # 2 3'b100 - delay by method # 3 3'b101 - delay by method # 4 3'b110 - delay by method # 5 3'b111 - delay by method # 6- USE THIS METHOD Notes: #= Input = In-ST = Output = Out-OD= I/O-TS = I/O-OD = Active low signal Input signal Input signal with Schmitt-Trigger Output signal (Tri-State driver) Output signal with Open-Drain driver Input & Output signal with Tri-State driver Input & Output signal with Open-Drain driver Zarlink Semiconductor Inc. 153 MVTX2804 12.4 Ball Signal Name Signal Name AVCC DEV_CFG[0] LA_D[0] LA_CLK LA_D[1] LA_D[2] LA_D[3] LA_D[4] LA_D[5] LA_D[6] LA_D[7] LA_D[8] LA_D[9] LA_D[10] LA_D[11] LA_D[12] LA_D[13] LA_D[14] LA_D[15] LA_D[16] LA_D[17] LA_D[18] LA_D[19] LA_D[20] LA_D[21] LA_D[22] LA_D[23] LA_D[24] LA_D[25] LA_D[26] LA_D[27] LA_D[28] LA_D[29] LA_D[30] Ball No. M1 M2 M3 K4 N1 P5 N2 L5 N3 P1 P2 P3 L4 R5 M5 R1 R2 R3 R4 M4 T4 T3 N5 T2 T1 U4 U3 N4 U2 U1 V3 P4 V2 V1 Y2 Signal Name LA_D[34] LA_D[35] LA_D[36] LA_D[37] LA_D[38] LA_D[39] LA_D[40] LA_D[41] LA_D[42] LA_D[43] LA_D[44] LA_D[45] LA_D[46] LA_D[47] LA_D[48] LA_D[49] LA_D[50] LA_D[51] LA_D[52] LA_D[53] LA_D[54] LA_D[55] LA_D[56] LA_D[57] LA_D[58] LA_D[59] LA_D[60] LA_D[61] LA_D[62] LA_D[63] LA_A[3] LA_A[4] LA_A[5] LA_A[6] LA_A[13] Ball No. V4 Y1 V4 Y1 AA3 AA2 V5 AA1 W4 Y4 AA4 AB4 AB3 W5 AB2 AB1 AC3 Y5 AC2 AC1 AD3 AD4 AA5 AD2 AB5 AD1 AE4 AC4 AE3 AE2 AE1 AC5 AF1 AD5 AF2 Data Sheet Signal Name LA_A[14] LA_A[15] LA_A[14] LA_A[15] LA_A[16] LA_A[17] LA_A[18] LA_A[19] LA_A[20] G0_CRS/LNK GREF_CLK[0] G0_TXCLK G0_TXD[0] G0_TXD[1] G0_TXD[2] MII_TX_CLK[0] G0_TXD[3] G0_TXD[4] G0_TXD[5] G0_RXCLK G0_COL G0_TXD[6] G0_TXD[7] G0_TX_EN G0_TX_ER G0_RXD[0] G0_RXD[1] G0_RXD[2] G0_RXD[3] G0_RXD[4] G0_RXD[5] G0_RXD[6] G0_RXD[7] G0_RX_DV G0_RX_ER Ball No. A1 B1 B2 C2 C1 D1 C3 E4 D2 E3 E2 E1 D3 F1 F2 F3 F4 F5 G1 G2 G5 G4 G3 H1 H2 H3 J1 H5 J2 J3 J4 K1 H4 K2 154 Zarlink Semiconductor Inc. Data Sheet Ball No. J5 K3 L1 L2 L3 K5 AH2 AJ2 AJ1 AK1 AG4 AK2 AH3 AJ3 AH4 AK3 AF4 AK4 AH5 AJ4 AG6 AF5 AJ5 AF6 AK5 AK6 AJ6 AG5 AH6 AF7 AK7 AJ7 AG8 AG7 AH7 Signal Name LA_D[31] LA_CS0# LA_CS1# LA_RW# LA_D[32] LA_D[33] G1_TXD[3] G1_TXD[4] G1_TXD[5] G1_TXD[6] G1_TXD[7] G1_TX_EN MII_TX_CLK[1] G1_TX_ER G1_RXD[0] G1_RXD[1] G1_RXD[2] G1_RXD[3] G1_RXCLK G1_COL G1_RXD[4] G1_RXD[5] G1_RXD[6] G1_RXD[7] G1_RX_DV G1_RX_ER GREF_CLK[2] G2_TXCLK G2_CRS/LKINK G2_TXD[0] G2_TXD[1] G2_TXD[2] G2_TXD[3] G2_TXD[4] MII_TX_CLK[2] Ball No. AK8 AJ8 T5 W3 W2 W1 U5 Y3 AG10 AK10 AJ10 AG11 AH10 AG12 AK11 AJ11 AH11 AK12 AF12 AJ12 AH12 AK13 AJ13 AH13 AF13 AK14 AG13 AJ14 AH14 AF14 AG14 AK15 AF17 AJ15 AH15 Signal Name G2_TXD[5] G2_TXD[6] LA_A[7] LA_A[8] LA_A[9] LA_A[10] LA_A[11] LA_A[12] G2_RXCLK G2_COL G2_RXD[6] G2_RXD[7] G2_RX_DV G2_RX_ER G3_CRS/LINK GREF_CLK[3] G3_TXCLK G3_TXD[0] G3_TXD[1] G3_TXD[2] G3_TXD[3] G3_TXD[4] MII_TX_CLK[3] G3_TXD[5] G3_TXD[6] G3_TXD[7] G3_TX_EN G3_TX_ER G3_RXCLK G3_COL G3_RXD[0] CM_CLK IND_CM G3_RXD[1] G3_RXD[2] Ball No. AF15 AF18 AG15 AF16 AF3 AG2 AG3 AE5 AG1 AH1 AG19 AK17 AF20 AH18 AJ18 AK18 AH19 AJ19 AK19 AH20 AJ20 AF21 AK20 AH21 AJ21 AK21 AF22 AG20 AG21 AG22 AH22 AJ22 AK22 AH23 AG23 MVTX2804 Signal Name G3_RXD[3] G3_RXD[4] G3_RXD[5] G3_RXD[6] GREF_CLK[1] G1_TXCLK G1_CRS/LINK G1_TXD[0] G1_TXD[1] G1_TXD[2] G4_TXD[1] G4_TXD[2] G4_TXD[3] G4_TXD[4] G4_TXD[5] MII_TX_CLK[4] G4_TXD[6] G4_TXD[7] G4_TX_EN G4_TX_ER G4_RXD[0] G4_RXD[1] G4_RXF[2] G4_RXCLK G4_COL G4_RXD[3] Gr_RXD[4] G4_RXD[5] G4_RXD[6] G4_RXD[7] G4_RX_DV GREF_CLK[5] G5_TXCLK G4_RX_ER G5_CRS/LINK Zarlink Semiconductor Inc. 155 MVTX2804 Ball No. AJ23 AK23 AF23 AH24 AF24 AG24 AF8 AH8 AK9 AJ9 AH9 AF9 AG9 AF10 AF11 AJ26 AH26 AJ27 AF26 AH27 AK27 AK28 AJ28 AJ29 AK29 AK30 AH28 AH29 AG27 AG28 AH30 AG30 AF28 AE26 AG29 Signal Name G5_TXD[0] G5_TXD[1] G5_TXD[2] G5_TXD[3] G5_TXD[4] G5_TXD[5] G2_TXD[7] G2_TX_EN G2_TX_ER G2_RXD[0] G2_RXD[1] G2_RXD[2] G2_RXD[3] G2_RXD[4] G2_RXD[5] G5_COL G5_RXD[3] G5_RXD[4] G5_RXD[5] G5_RXD[6] G5_RXD[7] G5_RX_DV G5_RX_ER G6_CRS/LINK MII_TX_CLK[6] GREF_CLK[6] G6_TXD[1] G6_TXD[2] G6_TXD[3] G6_TXD[4] G6_TXCLK G6_TXD[5] G6_TXD[6] G6_TXD[7] G6_TX-EN Ball No. AF27 AF29 AF30 AD26 AE30 AC26 AE29 AC27 AG16 AH16 AF19 AJ16 AG18 AK16 AG17 AH17 AJ17 AA27 AB30 AB29 Y26 AB28 Y27 AB27 AA30 AA29 AA29 Y30 W27 Y29 W26 Y28 W30 W29 V26 Signal Name G6_RXCLK G6_COL G6_TX_ER G6_RXD[0] G6_RXD[1] G6_RXD[2] G6_RXD[3] G6_RXD[4] G3_RXD[7] G3_RX_DV G3_RX_ER M_MDC M_MDIO G4_CRS/LINK GREF_CLK[4] G4_TXCLK G4_TXD[0] G7_TXD[3] G7_TXD[4] G7_TXD[5] G7_TXD[6] G7_TXD[7] G7_TX_EN G7_TX_ER MII_TX_CLK[7] G7_RXCLK C7_COL G7_RXD[0] G7_RXD[1] G7_RXD{2] G7_RXD{3] G7_RXD{4] G7_RXD{5] G7_RXD{6] G7_RXD{7] Ball No. W28 V27 V30 V29 V28 U26 U30 U29 U28 T30 T29 AJ24 AK24 AG25 AH25 AF25 AJ25 AG26 AK25 AK26 P29 P30 P26 N28 N29 N30 M28 M29 M30 N26 L28 L29 N27 L30 K28 Data Sheet Signal Name G7_RX_DV G7_RX_ER LE_DO LE_CLK0 LE_SYNCO# S_RST# RESOUT# T_MODE{0} T_MODE{1] T_D[0] T_D[1] G5_TXD[6] G5_TXD[7] MII_TX_CLK[5] G5_TX_EN G5_TX_ER G5_RXD[0]] G5_RXD[1] G5_RXD[2] G5_RXCLK T_D[13] T_D[14] T_D[15] P_D[0] P_D[1] P_D[2] P_D[3] P_D[4] P_D[5] P_D[6] P_D[7] P_D[8] P_D[9] P_D[10] P_D[11] 156 Zarlink Semiconductor Inc. Data Sheet Ball No. K29 K30 L27 K27 M26 J27 J28 J29 J30 L26 H28 M27 H29 H30 AE28 AE27 AB26 AD30 AD29 AD27 AD28 AC30 AA26 AC29 AC28 E30 H26 E29 E26 D29 E28 G26 D30 C30 E27 Signal Name P_D[12] P_D[13] P_D[14] P_D[15] P_A[0] P_A[1] P_A[2] P_WE# P_RD# P_CS# P_INT# B_D[0] B_D[1] B_D[2] G6_RXD[5] G6_RXD[6] G6_RXD[7] G6_RX_DV GREF_CLK[7] G6_RX_ER G7_TXCLK G7_CRS/LINK G7_TXD[0] G7_TXD[1] G7_TXD[2] B_D[14] B_D[15] B_D[16] B_D[17] B_D[18] B_D[19] B_D[20] B_D[21] B_D[22] B_D[23] Ball No. C29 D28 B30 F26 D26 A30 A29 B29 E25 B28 C28 A28 A27 C27 D27 B27 T28 U27 T27 R27 T26 R28 R29 R30 R26 P27 P28 A23 B23 C23 E22 A22 B22 C22 E21 Signal Name B_CLK B_D[24] B_D[25] NC1 NC2 NC3 NC4 NC5 AGND DEV_CFG[1] AVDD B_D[26] B_D[27] B_D[28] B_D[29] B_D[30] T_D[2] T_D[3] T_D[4] T_D[5] T_D[6] T_D[7] T_D[8] T_D[9] T_D[10] T_D[11] T_D[12] B_A[12] B_A[13] B_A[14] B_A[15] B_A[16] B_A[17] B_A[18] LB_A[20] Ball No. D22 D20 E20 D21 A21 D19 B21 C21 A20 B20 E19 C20 A19 B19 E18 C19 A18 D18 G28 G27 K26 G29 G30 H27 F27 F28 F29 F30 J26 E14 C15 B15 E13 A15 D14 MVTX2804 Signal Name LB_A[19] LB_A[18] LB_A[17] LB_A[16] LB_A[15] LB_A[14] LB_A[13] LB_A[12] LB_A[11] LB_A[10] LB_A[9] LB_A[8] LB_A[7] LB_A[6] LB_A[5] LB_A[4] LB_A[3] LB_D[63] B_D[3] B_D[4] B_D[5] B_D[6] B_D[7] B_D[8] B_D[9] B_D[10] B_D[11] B_D[12] B_D[13] LB_D[49] LB_D[48] LB_D[47] LB_D[46] LB_D[45] LB_D[44] Zarlink Semiconductor Inc. 157 MVTX2804 Ball No. C14 D13 B14 A14 C13 E12 B13 A13 D12 C12 B12 A12 C11 E11 B11 A11 E10 C10 B10 E9 E24 D25 B26 A26 A25 B25 C26 C25 E23 A24 B24 D23 D24 C24 B7 Signal Name LB_D[43] LB_D[42] LB_D[41] LB_D[40] LB_D[39] LB_D[38] LB_D[37] LB_D[36] LB_D[35] LB_D[34] LB_D[33] LB_D[32] LB_RW# LB_CS1# LB_CS0# LB_D[31] LB_D[30] LB_D[29] LB_D[28] LB_D[27] B_D[31] B_ADSC# B_WE# B_OE# B_A[2] B_A[3] B_A[4] B_A[5] B_A[6] B_A[7] B_A[8] B_A[9] B_A[10] B_A[11] LB_D[12] Ball No. E8 A7 D6 C6 E6 B6 A6 A5 B5 C5 B4 D5 A4 A3 E5 C4 B3 D4 A2 AD6 AE15 AE16 AE24 B18 C18 A17 E17 B17 C17 E16 D17 A16 B16 E15 C16 Signal Name LB_D[11] LB_D[10] LB_D[9] LB_D[8] LB_D[7] LB_D[6] LB_D[5] LB_D[4] LB_D[3] LB_D[2] LB_D[1] LB_CLK LB_D[0] SCAN_EN AGND NC6 NC7 NC8 NC9 VSS VSS VSS VSS LB_D[62] LB_D[61] LB_D[60] LB_D[59] LB_D[58] LB_D[57] LB_D[56] LB_D[55] S_CLK LB_D[54] LB_D[53] LB_D[52] Ball No. D16 D15 P15 P16 P17 P18 R13 R14 R15 R16 R17 R18 R25 R26 T13 T14 T15 T16 T17 T18 T25 T6 U13 U14 U15 U16 A10 D11 D10 D8 D9 C9 B9 A9 C8 Data Sheet Signal Name LB_D[51] LB_D[50] VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS LB_D[26] LB_D[25] LB_D[24] LB_D[23] LB_D[22] LB_D[21] LB_D[20] LB_D[19] LB_D[18] 158 Zarlink Semiconductor Inc. Data Sheet Ball No. B8 A8 C7 E7 D7 AE7 AE9 F10 F21 F22 F9 G25 G6 J25 J6 K25 K6 AE12 AE13 AE14 AE17 AE18 AE19 F12 F13 F14 F17 F18 F19 AE25 AE6 F15 F16 F24 F25 Signal Name LB_D[17] LB_D[16] LB_D[15] LB_D[14] LB_D[13] VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VD33 VD33 VD33 VD33 VD33 VD33 VD33 VD33 VD33 VD33 VD33 VD33 VSS VSS VSS VSS VSS VSS Ball No. F6 F7 N13 N14 N15 N16 N17 N18 P13 P14 U17 U18 V13 V14 V15 V16 V17 V18 AA25 AA6 AB25 AB6 AD25 AE10 AE21 AE22 M25 M6 N25 N6 P25 U25 U6 V6 W25 Signal Name VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDD VDD VDD VDD VDD VDD VDD VDD VD33 VD33 VD33 VD33 VD33 VD33 VD33 VD33 VD33 Ball No. W6 MVTX2804 Signal Name VD33 Zarlink Semiconductor Inc. 159 MVTX2804 12.5 12.5.1 AC/DC Timing Absolute Maximum Ratings Data Sheet Storage Temperature-65C to +150C Operating Temperature-40C to +85C Supply Voltage VDD33 with Respect to VSS +3.0 V to +3.6 V Supply Voltage VDD with Respect to VSS +2.38 V to +2.75 V Voltage on Input Pins-0.5 V to (VDD33 + 3.3 V) Caution: Stress above those listed may damage the device. Exposure to the Absolute Maximum Ratings for extended periods may affect device reliability. Functionality at or above these limits is not implied. 12.5.2 DC Electrical Characteristics VDD33 = 3.0 V to 3.6 V (3.3v +/- 10%)TAMBIENT = -40C to +85C VDD = 2.5V +10% -5% 12.5.3 Recommended Operation Conditions Preliminary Symbol fosc IDD1 IDD2 VOH VOL VIH-TTL VIL-TTL IIH-5VT Parameter Description Frequency of Operation Supply Current - @ 133 MHz (3.3 V supply) Supply Current - @ 133 MHz (2.5 V supply) Output High Voltage (CMOS) Output Low Voltage (CMOS) Input High Voltage (TTL 5V tolerant) Input Low Voltage (TTL 5V tolerant) Input Leakage Current (0.1 V < VIN < VDD) (all pins except those with internal pull-up/pull-down resistors) Input Capacitance Output Capacitance I/O Capacitance Min Type 133 Max Unit MHz 720 1400 VDD33 0.5 930 1700 mA mA V 0.5 VDD33 x 70% VDD33 + 2.0 VDD33 x 30% 10 V V V A CIN COUT CI/O 5 5 7 pF pF pF 160 Zarlink Semiconductor Inc. Data Sheet 12.5.4 Typical CPU Timing Diagram for a CPU Write Cycle Description Write Cycle Write Set up Time Write Active Time Write Hold Time Write Recovery time Data Set Up time Data Hold time Symbol TWS TWA TWH TWR TDS TDH (SCLK=133Mhz) Min (ns) 10 15 2 22.5 10 2 Max (ns) MVTX2804 At least 2 SCLK At least 3 SCLK Table 6 - CPU Write Cycle P_ADDR ADDR0 ADDR1 P_CS# TWS P_WE# TWA at least 2 SCLKs TWH TWS TWR Recovery Time TWA at least 2 SCLKs TWH TDH DATA 1 TDH DATA to VTX2600 DATA 0 TDS Set up time Hold time TDS Figure 7 - Typical CPU Timing Diagram for a CPU Write Cycle Zarlink Semiconductor Inc. 161 MVTX2804 12.5.5 Typical CPU Timing Diagram for a CPU Read Cycle Data Sheet P_ADDR ADDR0 ADDR1 P_CS# TRS P_RD# TRA at least 2 SCLKs TRH TRS TRR Recovery Time at least 3 SCLKs TRA at least 2 SCLKs TRH DATA to CPU TDV Valid time DATA 0 DATA 1 TDI 2ns TDV Inactive time TDI Figure 8 - Typical CPU Timing Diagram for a CPU Read Cycle Description Read Cycle Read Set up Time Read Active Time Read Hold Time Read Recovery time Data Valid time Data Inactive time Symbol TRS TRA TRH TRR TDS TDI (SCLK=133Mhz) Min (ns) 10 15 2 22.5 10 2 At least 3 SCLK At least 2 SCLK Max (ns) Table 7 - CPU Read Cycle 162 Zarlink Semiconductor Inc. Data Sheet 12.6 12.6.1 Local Frame Buffer ZBT SRAM Memory Interface Local ZBT SRAM Memory Interface A MVTX2804 LA_CLK L1 L2 LA_D[63:0] Table 8 - Local Memory Interface - Input setup and hold timing LA_CLK L3-max L3-min LA_D[63:0] L4-max L4-min LA_A[20:3] L6-max L6-min LA_CS[1,0]# L9-max L9-min LA_RW# Figure 9 - Local Memory Interface - Output valid delay timing (SCLK= 133MHz) Symbol L1 L2 L3 L4 L6 L9 Parameter LA_D[63:0] input set-up time LA_D[63:0] input hold time LA_D[63:0] output valid delay LA_A[20:3] output valid delay LA_CS[1:0]# output valid delay LA_WE# output valid delay Min (ns) 2.5 1 3.0 3.0 3.0 3.0 5 5 5 5 1 2CL = 25pf 3CL = 30pf 4CL = 30pf 5CL = 25pf Max (ns) Note: Table 9 - AC Characteristics - Local frame buffer ZBT-SRAM Memory Interface A Zarlink Semiconductor Inc. 163 MVTX2804 12.6.2 Local ZBT SRAM Memory Interface B Data Sheet LB_CLK L1 L2 LB_D[63:0] Figure 10 - Local Memory Interface - Input setup and hold timing LB_CLK L3-max L3-min LB_D[63:0] L4-max L4-min LB_A[20:3] L6-max L6-min LB_CS[1,0]# L9-max L9-min LB_RW# Figure 11 - Local Memory Interface - Output valid delay timing (SCLK= 133MHz) Symbol L1 L2 L3 L4 L6 L9 Parameter LB_D[63:0] input set-up time LB_D[63:0] input hold time LB_D[63:0] output valid delay LB_A[20:3] output valid delay LB_CS[1:0]# output valid delay LB_WE# output valid delay Min (ns) 2.5 1 3.0 3.0 3.0 3.0 5 5 5 5 CL = 25pf CL = 30pf CL = 30pf CL = 25pf Max (ns) Note: Table 10 - AC Characteristics - Local frame buffer ZBT-SRAM Memory Interface B 12.7 12.7.1 Local Switch Database SBRAM Memory Interface Local SBRAM Memory Interface 164 Zarlink Semiconductor Inc. Data Sheet MVTX2804 B_CLK L1 L2 B_D[31:0] Figure 12 - Local Memory Interface - Input setup and hold timing B_CLK L3-max L3-min B_D[31:0] L4-max L4-min B_A[18:2] L6-max L6-min B_ADSC# L10-max L10-min B_WE# L11-max L11-min B_OE# Figure 13 - Local Memory Interface - Output valid delay timing (SCLK= 133MHz) Symbol L1 L2 L3 L4 L6 L10 L11 Parameter B_D[31:0] input set-up time B_D[31:0] input hold time B_D[31:0] output valid delay B_A[18:2] output valid delay B_ADSC# output valid delay B_WE# output valid delay B_OE# output valid delay Min (ns) 2.5 1 3.0 3.0 3.0 3.0 3.0 5 5 5 5 4 CL = 25pf CL = 30pf CL = 30pf CL = 25pf CL = 25pf Max (ns) Note: Table 11 - AC Characteristics - Local Switch Database SBRAM Memory Interface Zarlink Semiconductor Inc. 165 MVTX2804 12.8 12.8.1 AC Characteristics Media Independent Interface Data Sheet MII_TXCLK[7:0] M6-max M6-min G[7:0]_TXEN M7-max M7-min G[7:0] _TXD[3:0] Figure 14 - AC Characteristics - Media Independent Interface G[7:0]_RXCLK M2 G[7:0]_RXD[3:0] M3 G[7:0]_CRS_DV M4 M5 Figure 15 - AC Characteristics - Media Independent Interface (MII_TXCLK & G_RXCLK = 25MHz) Symbol M2 M3 M4 M5 M6 M7 Parameter G[7:0]_RXD[3:0] Input Setup Time G[7:0]_RXD[3:0] Input Hold Time G[7:0]_CRS_DV Input Setup Time G[7:0]_CRS_DV Input Hold Time G[7:0]_TXEN Output Delay Time G[7:0]_TXD[3:0] Output Delay Time Min (ns) 4 1 4 1 3 3 11 11 CL = 20 pF CL = 20 pF Max (ns) Note: Table 12 - AC Characteristics - Media Independent Interface 166 Zarlink Semiconductor Inc. Data Sheet 12.8.2 Gigabit Media Independent Interface MVTX2804 G[7:0]_TXCLK G12-max G12-min G[7:0]_TXD[7:0] [15:0] G13-max G13-min G[7:0]_TX_EN G14-max G14-min G[7:0]_TX_ER Figure 16 - AC Characteristics - GMII G[7:0]_RXCLK G1 G[7:0]_RXD[7:0] G3 G[7:0}_RX_DV G5 G6 G[7:0]_RX_ER G7 G[7:0]_RX_CRS G8 G4 G2 Figure 17 - AC Characteristics - Gigabit Media Independent Interface Zarlink Semiconductor Inc. 167 MVTX2804 (G_RCLK & G_REFCLK = 125MHz) Symbol Parameter G[7:0]_RXD[7:0] Input Setup Times G[7:0]_RXD[7:0] Input Hold Times G[7:0]_RX_DV Input Setup Times G[7:0]_RX_DV Input Hold Times G[7:0]_RX_ER Input Setup Times G[7:0]_RX_ER Input Hold Times G[7:0]_CRS Input Setup Times G[7:0]_CRS Input Hold Times G[7:0]_TXD[7:0] Output Delay Times G[7:0]_TX_EN Output Delay Times G[7:0]_TX_ER Output Delay Times Data Sheet Min (ns) Max (ns) Note: G1 G2 G3 G4 G5 G6 G7 G8 G12 G13 G14 2 1 2 1 2 1 2 1 1.5 2 1 5 5 5 CL = 20pf CL = 20pf CL = 20pf Table 13 - AC Characteristics - Gigabit Media Independent Interface 12.8.3 PCS Interface G[7:0]_TXCLK G30-max G30-min G[7:0]_TXD[9:0] [15:0] Figure 18 - AC Characteristics - PCS Interface Figure 19 - AC Characteristics - PCS Interface 168 Zarlink Semiconductor Inc. Data Sheet (G_RCLK & G_REFCLK = 125MHz) Symbol Parameter Min (ns) Max (ns) MVTX2804 Note: G21 G22 G23 G24 G25 G26 G30 G[7:0]_RXD[9:0] Input Setup Times ref to G_RXCLK G[7:0]_RXD[9:0] Input Hold Times ref to G_RXCLK G[7:0]_RXD[9:0] Input Setup Times ref to G_RXCLK1 G[7:0]_RXD[9:0] Input Hold Times ref to G_RXCLK1 G[7:0]_CRS Input Setup Times G[7:0]_CRS Input Hold Times G[7:0]_TXD[9:0] Output Delay Times 2 1 2 1 2 1 1 5 CL = 20pf Table 14 - AC Characteristics - PCS Interface 12.8.4 LED Interface LED_CLK LE5-max LE5-min LED_SYN LE6-max LE6-min LED_BIT Figure 20 - AC Characteristics - LED Interface Variable FREQ. Symbol Parameter Min (ns) Max (ns) Note: LE5 LE6 LED_SYN Output Valid Delay LED_BIT Output Valid Delay 1 1 7 7 CL = 30pf CL = 30pf Table 15 - AC Characteristics - LED Interface 12.8.5 MDIO Input Setup and Hold Timing MDC D1 D2 MDIO Figure 21 - MDIO Input Setup and Hold Timing Zarlink Semiconductor Inc. 169 MVTX2804 Data Sheet MDC D3-max D3-min MDIO Figure 22 - MDIO Output Delay Timing 1MHz Symbol Parameter Min (ns) Max (ns) Note: D1 D2 D3 MDIO input setup time MDIO input hold time MDIO output delay time 10 2 1 Table 16 - MDIO Timing 20 CL = 50pf 12.8.6 I2C Input Setup Timing SCL S1 S2 SDA Figure 23 - I2C Input Setup Timing SCL S3-max S3-min SDA Figure 24 - I2C Output Delay Timing 170 Zarlink Semiconductor Inc. Data Sheet 500KHz Symbol Parameter Min (ns) Max (ns) MVTX2804 Note: S1 S2 S3* SDA input setup time SDA input hold time SDA output delay time 20 1 1 20 CL = 30pf * Open Drain Output. Low to High transistor is controlled by external pullup resistor. Table 17 - I2C Timing 12.8.7 Serial Interface Setup Timing STROBE D1 D2 D4 D1 D2 D5 PS_DI Figure 25 - Serial Interface Setup Timing STROBE D3 -max D3 -min PS_DO Figure 26 - Serial Interface Output Delay Timing (SCLK =133 MHz) Symbol Parameter Min (ns) Max (ns) Note: D1 D2 D3 D4 D5 PS_DI setup time PS_DI hold time PS_DO output delay time Strobe low time Strobe high time 20 10 1 5s 5s Table 18 - Serial Interface Timing 50 CL = 100pf Zarlink Semiconductor Inc. 171 MVTX2804 Data Sheet 172 Zarlink Semiconductor Inc. E1 E MIN MAX A 2.20 2.46 A1 0.50 0.70 A2 1.17 REF 40.20 D 39.80 D1 34.50 REF E 40.20 39.80 E1 34.50 REF b 0.60 0.90 e 1.27 596 Conforms to JEDEC MS - 034 e D1 D A2 NOTE: b A1 A 1. CONTROLLING DIMENSIONS ARE IN MM 2. DIMENSION "b" IS MEASURED AT THE MAXIMUM SOLDER BALL DIAMETER 3. SEATING PLANE IS DEFINED BY THE SPHERICAL CROWNS OF THE SOLDER BALLS. 4. N IS THE NUMBER OF SOLDER BALLS 5. NOT TO SCALE. 6. SUBSTRATE THICKNESS IS 0.56 MM Package Code ISSUE ACN DATE APPRD. Previous package codes: For more information about all Zarlink products visit our Web Site at www.zarlink.com Information relating to products and services furnished herein by Zarlink Semiconductor Inc. trading as Zarlink Semiconductor or its subsidiaries (collectively "Zarlink") is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink's conditions of sale which are available on request. Purchase of Zarlink's I2C components conveys a licence under the Philips I2C Patent rights to use these components in an I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright 2002, Zarlink Semiconductor Inc. All Rights Reserved. TECHNICAL DOCUMENTATION - NOT FOR RESALE |
Price & Availability of MVTX2804
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |